Bogen FMH15T User Manual

FMH15T

Flange Mounted, 15W, Horn Loudspeaker

Installation Instructions

The FMH15T is designed to be mounted by its flange. Figure 1 shows the mounting hole locations.

Components

Bogen recommends using the SGHD8 Grille with the FMHAR8 Adapter Ring for proper mounting of the horn.The SGHD8 Grille will mount to the BBFM6 Flush Mount Enclosure or BBSM6 Surface Mount Enclosure. See

1. Make the electrical connections (see Figure 2). Connect the 70V or 25V “hot” lead to the #1 terminal and the system common lead to the #2 terminal. Follow this pattern on all similar speakers to ensure proper phasing; however, the speakers will work perfectly well if the connections are reversed.

Figure 3 on other side for mounting details.

Figure 1

2. Adjust the tap selector switch to the desired wattage using the chart below.

TAP SET 70V WATTS 25V WATTS

1 0.9 0.125

2 1.8 0.25

3 3.6 0.5

4 7.5 0.9

5 15 1.8

* Do not use these positions

* * * *

IMPORTANT

7.0

Figure 2

137-01A 0505

54-2

unications,

Inc

Assembly Instructions

1) Place gasket supplied with FMH15T onto FMHAR8 Adapter Ring over the studs. Then mount FMH15T to FMHAR8 Adapter Ring, sliding flange hole over adapter ring studs and secure with nuts supplied with adapter ring.

2) Slide FMH

15T/FMHAR8 assembly over studs in SGHD8

Grille and secure with nuts supplied with grille.

3) Mount BBSM6 or BBFM6 enclosure as necessary.

4) Use 4 white security screws and tool supplied with SGHD8 Grille to mount the speaker/grille assembly onto the enclosure.

Figure 3

The FMH15T is warranted to be free from defects in material or workmanship for two (2) years from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446,

The product will be returned to you freight prepaid.

USA. abuse, misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.

THE FOREGOING LIMITED W EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT

disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be liable for special, incidental or consequential damages (including, but not limited to, loss of profits, loss of data or loss of use damages) aris ing out of the manufacture, sale or supplying of products, even if Bogen has been advised of the possibility of such damages or losses. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call 201-934-

8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns require a Return Authorization number.

8/10/2004

ARRANTY

ALLOWABLE BY LAW.

IS BOGEN'S SOLE

This warranty does not extend to any of our products that have been subjected to

AND EXCLUSIVE W

Bogen's liability arising out of the manufacture, sale or supplying of products or their use or

ARRANTY

AND THE PURCHASER'S SOLE

AND

50 Spring Street, Ramsey, NJ 07446, U.S.A.

201-934-8500; Fax: 201-934-9832

www.bogen.com