Bogen CSD2X2L User Manual
CEILING GRID
CEILING GRID
SUPPORT RAIL
CROSSBAR INCLUDED
(2 ft. X 4ft. CEILING GRID ONLY)
CEILING TILE
(CUT IN HALF, OR NO MORE
THAN 23-3/4")
2 ft. X 2ft.
TILE SPACE
2 ft. X 4ft.
TILE SPACE
Low-Impedance Drop-In
Ceiling Speaker
with Back Can
CSD2X2L
(
U
)
Bogen’s CSD2X2L(U) Drop-In Ceiling Speakers are 8- ohm,
full-range speakers that allow for fast and easy installation, which saves installation time, effort, and cost.
The CSD2X2L(U) is a 2' x 2' speaker that fits perfectly
into place in 2' x 2' ceiling grids – without needing to
cut ceiling tiles or requiring the use of tile support rails.
The CSD2X2L(U) can also be easily installed in 2' x 4'
ceiling grids – just make one cut to the ceiling tile, position the support rail (included), and drop the speaker
into place.
• Finely perforated grille over the entire front of speaker
• Fully enclosed, industrial grade steel construction
• Enclosed Back Can
• 8'' main cone with secondary high-frequency cone
• Low-Impedance: 8-ohm speaker, 15W max. power
• Seismic tether points
• Complies with Requirements of UL-2043
• Support Rail Crossbar (included)
• Available in Off-white and Bright White ("U" versions)
grille finish
CSD2X2L(U
)
CSD2X2L(U
)
Frequency Response . . . . . . . . . . 85 Hz - 20 kHz
SPL @ 1W / 1m . . . . . . . . . . . . . . . 94 dB
Maximum Power . . . . . . . . . . . . . . 15 watts @ 8-ohm
Dispersion @ 2 kHz
(6 dB down) . . . . . . . . . . . . . . . . . .100°
Cone Material & Surround . . . . . . Treated paper
Cones . . . . . . . . . . . . . . . . . . . . . . .
8" main cone with secondary
high frequency cone
Magnet Weight . . . . . . . . . . . . . . . .10 oz.
Connection . . . . . . . . . . . . . . . . . . . Via wire nuts (included in electrical box)
Dimensions . . . . . . . . . . . . . . . . . .23-13/16" W x 5" H x 23 -13/16" D
Product Weight . . . . . . . . . . . . . . .12 lb.
Plenum-Rated, complies with Requirements of Standard UL-2043.
The speaker shall be a Bogen Model CSD2X2L(U) Low-Impedance
Drop-In Ceiling Speaker, which shall be fully enclosed and
constructed of industrial grade steel. It shall be comprised of a
damped high-compliance factory-mounted 8" loudspeaker that shall
consist of an 8" treated paper main cone, a secondary high frequency
cone, and a 10 ounce magnet. The unit shall have an 8-ohm nominal
impedance with maximum power of 15 watts. Output shall be 94 dB
@ 1 watt /1 meter (min.). Frequency response shall be 85 Hz - 20
kHz (min.). The speaker shall have a non-reflective, Off-white or
Bright White ("U" versions) metal finish grille.
The speaker assembly will fit into 2' x 2' and 2' x 4' ceiling tiles.
For 2' x 2' installations, a support rail shall not be needed and no
cuts to the ceiling shall be necessary. For 2' x 4' installations, a single
cut to the ceiling tile and an included support rail shall be needed.
The speaker shall measure 23-13/16" W x 5" H x 23-13/16" D and
weigh 12 lb.
SPECIFICATIONS
Architect and Engineer Specifications
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel: 201-934-8500 • Fax: 201-934-9832
www.bogen.com
Specifications subject to change without notice.
© 2008 Bogen Communications, Inc.
54-9283-01A 0807
—
FINELY PERFORATED
METAL FINISH GRILLE
Low-Impedance Drop-In Ceiling Speaker CSD2X2L(U
)
SUPPORT RAIL
CROSSBAR INCLUDED
(FOR USE WITHIN 2' X 4' TILE SPACE ONLY)
SEISMIC
TETHER
POINTS (4X)
Lead Color
Red
+
—
Black
WIRE
NUTS
COVER
WIRE
NUTS
COVER
Loading...