MAGNECTIC BIKE
OWNER’S MANUAL
MAGNECTIC BIKE
IMPORTANT !
Please read all instructions carefully before using this product.
Retain this manual for future reference.
1
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine pages.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. The maximum weight capacity for this product is 110 kgs.
WARNING: Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.
2
OVERVIEW DRAWING
3
PARTS LIST
No.
Description Qty No.
Description Qty
001 Screw ST4.2×25 6 030 Round Knob M16 1
002 Pan Head Phillips Self Drilling
Screw ST4.2x25
8 031 Seat Post Bushing 1
003 Cover Cap 2 032 Seat Post Cover 1
004 Left Chain Cover 1 033 Hexagon Nut M10 2
005 Turntable 2 034 Eyebolt M6x36 2
006 Screw ST4.2×10 14 035 U Bracket 2
007 Right Chain Cover 1 036 Spring Ø6 2
008 Plastic stud 2 037 Nut M6 2
009 End Cap For Rear Stabilizer 2 038 Flywheel Ф250 1
010 Rear Stabilizer 1 039 Nylon Nut M8 3
011 Bolt M8x70 2 040 Eyebolt M8x85 1
012 Big Curve Washer Ø8 4 041 Big WasherФ8xФ20x2.0 4
013 Front Stabilizer 1 042 Bolt M8x20 1
014 End Cap For Front Stabilizer 2 043 Pressing 1
015 Cap Nut M8 2 044 Idle Wheel 1
016 Hexagon Nut 7/8" 1 045 WasherФ6xФ12x1.0 1
017 Washer Ø23xØ34.5x2.5 1 046 Bolt M6X10 1
018 Bearing Nut II 7/8" 1 047 Seat Cushion DD-982AT 1
019 ball bearing 2 048 Seat Sliding Tube 1
020 Bearing Cup 2 049 Nylon Nut M8 3
021 Bearing Nut I 15/16" 1 050 Seat Sliding Tube End Cap 2
022 Washer Ø24xØ40x3.0 1 051 Limit seat assembly 1
023 Belt Pulley with Crank Ø260 1 052 Seat Post 1
024 Belt PJ380 J6 1 053 WasherФ10xФ20x2.0 1
025 Right Pedal 1 054 Screw nut M10 1
026 Tension Cable L=1300mm 1 055 Handlebar Post Cover 1
027 Main Frame 1 056 Extension Sensor Wire
(L=1000mm)
1
028 Sensor with Wire L=1100m 1 057 Bolt M8x15 6
029 Screw ST2.9×12 2 058 Tension Control Knob 1
4
PARTS LIST
No.
Description Qty No.
Description Qty
059 Handlebar Post 1 067 Screw ST4.2×20 2
060 Bolt M5X10 4 068 Handlebar Foam Grip 2
061 Big Curve Washer Ø5 1 069 Bolt M8x70 2
062 Bolt M5X55 1 070 Screw ST2.9×16 1
063 Computer 1 071 Left Pedal 1
064 End Cap for Handlebar 2 072 WasherФ8xФ16x1.5 8
065 Handlebar 1
066 Hand Pulse Sensor with Wire
L=750mm
2
Loading...