BRM 3600
For use under U.S. Patent numbers 6159132, D459773, D438264
This page intentionally left blank
General Information
Safety
Before you undertake any exercise program,
please be sure to consult with your doc
Frequent strenuous exercise should be
approved by your doctor and proper use
of your product is essential. Excessive or incorrect
training may result to health injuries. Please read
this manual carefully before commencing the
assembly of your product or starting to exercise.
• Please keep all children away from this item
when in use. Do not allow children to climb or
play on them when they are not in use.
• Supervise teenagers while they use this unit.
• For your own safety, always ensure that there
is at least 3 feet of free space in all directions
around your product while you are exercising.
• Regularly check to see that all nuts, bolts and
fittings are securely tightened. Periodically
check all moving parts for obvious signs of
wear or damage.
•
Any adjustment devices that could interfere with
the user's movement on this unit should not be
left projecting.
• Clean only with a damp cloth, do not use
solvent cleaners. If you are in any doubt, do
not use your product; contact CUSTOMER
SUPPORT.
• Before use, always ensure that your product
is positioned on a solid, flat surface. If
necessary, use a rubber mat underneath to
reduce the possibility of slipping.
Always wear appropriate clothing and
•
footwear such as training shoes when
exercising. Do not wear loose clothing that
could become caught in moving parts during
exercise.
• Do not use this unit if it is not functioning
properly or if it is not fully assembled.
• Do not use this unit for commercial purposes.
This unit is for home use only.
• Before use, you must read and understand all
instructions & warnings stated in this Owner’s
Manual as well as posted on the equipment.
• It is the facility owner’s responsibility to properly
instruct users on the proper operation of the
equipment and to warn them of the potential
hazards.
• If at any time during exercise you feel faint, dizzy
or experience pain, stop and consult your
physician.
tor.
Assembling Tools
- Ruler with both metric and English measurements
- 2 x Adjustable Wrenches
- 1 x Philips (”Crosshead”) Screw Driver
Weight Limit
Your product is suitable for users weighing:
250 pounds or less.
Storage and Use
Your product is intended for use in clean
dry conditions. You should avoid storage in
excessively cold or damp places as this may
lead to corrosion and other related problems.
Warranty
Body Flex Sports warrants your product for
a period of 1 year for the frame and 90 days
on all parts if the item is used for the intended
purpose, properly maintained and not used
commercially. Any alterations or incorrect
assembly of the product will void this warranty.
Proof of purchase must be presented for any
warranty validation (no exceptions). This
warranty applies to the original purchaser only
and is not transferable.
This warranty does not cover abuse or defects
caused during use, storage or assembly.
During the warranty period, Body Flex Sports
reserves the right to:
a). provide replacement parts to the
purchaser in an effort to repair the item.
b). repair the product returned to our
warehouse (at the purchaser’s cost).
c). replace the product if neither of the two
previously mentioned actions effect repair.
This warranty does not cover normal wear and
tear on upholstery.
Questions
If you have any questions concerning the
assembly of your item or if any parts are
missing, please DO NOT RETURN THE
ITEM TO THE STORE OR CONTACT THE
RETAILER. Our dedicated customer service
staff can help you with any questions you may
have regarding the assembly of this unit and
can also mail you replacement parts.
Customer Support
Customer Support is open 9:00 a.m. to 5:00
p.m. (Pacific Time) Monday through Friday.
Please contact us by any of the following
means.
Body Flex Sports, Inc.
21717 Ferrero Parkway, Walnut, CA 91789
Telephone: (888) 266 - 6789
Fax: (909) 598 - 6707
Email: info@bodyflexsports.com
BRM 3600 Stride Cycle Page 1
Hardware & Tool List
Bolts
The following hardware is used to assemble your unit. Please take
PLEASE NOTE: some of these parts may have already been pre-assembled on your unit.
a moment to familiarize yourself with these items.
#2. Bolt (M8 x 15 mm)
[2 pieces]
#38. Bolt (M8 x 20 mm)
[4 pieces]
Washers
#4. Spring Washer
#42. Washer
[1 piece]
(for M8 bolt)
[4 pieces]
(for M10 bolt, T2.0 mm)
Nuts
#12. Bolt (M8 x 45 mm)
[4 pieces]
#57. Screw (M5 x 50mm)
#5. Washer
#47. Spring Washer (for bolt #18)
[1 piece]
(for M8 bolt)
[2 pieces]
[2 pieces]
#18. Left / Right Pedal Bolt
#63. Screw (M4 x 10mm)
#56. Arc-Washer (for M5 bolt)
[2 pieces]
[2 pieces]
#71. Washer
[7 pieces]
Pre-assemble 3 pieces
[1 piece]
(for M8 bolt)
#27. Carriage Bolt (M8 x 73 mm)
#65. Bolt (M8 x 30 mm)
#37. Arc-Washer
[4 pieces]
[2 pieces]
(for M8 bolt)
[8 pieces]
Tools
#72. Nylon Nut
[7 pieces]
Pre-assemble 3 pieces
(for M 8 bolt)
#46. Nylon Nut
[2 pieces]
(for bolt #18)
#49. Cap Nut
[4 pieces]
(for M8 carriage bolt)
Knobs
#7. Knob Bolt
[2 pieces]
(M8x36 mm)
#43. Knob (M10)
[1 piece]
#39. Spring Loaded Knob
[1 piece]
Caps
#3. Bolt Cap
(for M8 bolt)
[4 pieces]
#45. Bolt Cap
[2 pieces]
(for bolt #18)
Misc.
#66. Clamp Cover [1 piece]
BRM 3600 Stride Cycle Page 2
Parts Listing
38....................Bolt (M8x20 mm)
39. ................... Spring Loaded Knob
42. ................... Washer (for M10 bolt, 2.0 mm Thick)
43. ................... Knob (M10)
47. ................... Spring Washer (for bolt #18)
51. ................... Computer
The following parts list describes all of the parts illustrated on the
exploded diagram on the following page. Please note, most of
these parts are already pre-assembled on your unit.
Part # Description
1. ..................... Handle Bar Foam Grip
2. ..................... Bolt (M8 x 15 mm)
3. ..................... Bolt Cap (for M8 bolt)
4. ..................... Spring Washer (for M8 bolt)
5. ..................... Washer (for M8 bolt)
6. ..................... Bushing for Coupler Bar
7. ..................... Knob Bolt (M8x36 mm)
8. ..................... L/R Coupler Bar
9. ..................... Nylon Nut (for M10 bolt)
10. ................... Bolt Cap (for M10 bolt)
11. ................... Bushing
12. ................... Bolt (M8x45 mm)
13. ................... Pedal
14....................Pedal Tube
15....................Washer (for M10 bolt)
17....................Bolt (M10x50 mm)
18L..................Left Pedal Bolt
18R. ................Right Pedal Bolt
19....................Bushing for Pedal Connection Joint
20....................Pedal Connection Joint
22....................End Cap (rectangular 25x40 mm)
25....................Adjustable End Cap for Rear Stabilizer
26....................Rear Stabilizer
27....................Carriage Bolt (M8x73 mm)
28....................End Cap (round 28mm)
29L/29R...........Handle Bar
30....................Handle Bar Sleeve
31....................Spacer
32. ................... Bolt (M10x55 mm)
33....................Seat
34....................End Plug (square 38mm)
35....................Horizontal Seat Bar
36....................Seat Post
37....................Arc-Washer (for M8 bolt)
Part # Description
40. ................... Tension Wire
41. ................... U Bracket
44. ................... Seat Post Sleeve
45. ................... Bolt Cap (for bolt #18)
46. ................... Nylon Nut (for bolt #18)
48. ................... Main Frame
49. ................... Cap Nut (for M8 carriage bolt)
52. ................... Main Sensor Wire (upper)
53....................Pulse Sensor Wire (upper)
54....................Main Sensor Wire (middle)
55....................Tension Controller
56....................Arc-Washer (for M5 bolt)
57....................Screw (M5 x 50mm)
58....................Center Post
59....................End Cap (round 25 mm)
60....................Pulse Handle Bar Foam Grip
61....................Pulse Sensor
62....................Screw
63....................Screw (M4 x 10mm)
64....................Pulse Sensor Wire (lower)
65....................Bolt (M8x30 mm)
66....................Clamp Cover
67....................Main Sensor Wire (lower)
68....................End Cap for Front Stabilizer
69....................Front Stabilizer
70....................Pulse Handle Bar
71. ...................Washer (for M8 bolt)
72. ...................
Nylon Nut (for M8 bolt)
BRM 3600 Stride Cycle Page 3
Exploded Diagram
The following diagram is provided to help you familiarize yourself with the parts and
hardware that will be used during the assembly process. Please note that not all of the
parts and hardware you see here will be used while you are assembling the machine
because some of these items are already pre-installed. Please continue to the next
page to begin the assembly process and use this page only as a reference guide for
parts and hardware.
BRM 3600 Stride Cycle Page 4
Loading...