Bodine AC, DC, BL Accessories Catalog

Model No.

Description

Model No.

Description

Accessories

Model No.

Description

Part No.

µF /VAC

Box-Type Metalized Film Capacitor (Plastic Case)

Part No.

µF /VAC

Part No.

µF /VAC

Round Metal Can-Type Capacitor

AC | DC | BL

A EB, C

K, L, M, N

“L” Brackets

A 0969 Kit for E, F and FX gearmotors (will not ﬁ t 48R-F or 48R-FX) B 0970 Kit for WX gearmotors C 0979 Kit for 34R and 34B motors D 0980 Kit for 34R-Z gearmotors E 0990 Kit for 24A motors F 5968 Kit for 30R and 33A motors; 30R-D, 24A-D, 22B-D, 24A-Z, 33A-Z and 22B-Z gearmotors

B E

Motor and Gearmotor Accessory Kits

D H

A 0967 Base plate kit for 3F gearmotors B 0977 IP-44 protection kit for 33A gearmotors and motors C 0978 IP-44 protection kit for 42A gearmotors and motors D 0984 Die cast terminal box kit for 34R, 42R, 48R, and 33A, 42A motors and gearmotors (DC: does not ﬁ t on 12 or 24VDC models) E 0985 Oversized die cast t-box kit. Fits capacitor for use with 42R-FX gearmotors. Also ﬁ ts 42R, 48R, 33A and 42A motors/gearmotors. — 1982 Die cast terminal box with terminal block for 30R motors and gearmotors — 1984 Die cast terminal box kit with terminal block for 34R, 42R, 48R, 33A and 42A motors/gmtrs. 90/130, 130V and 180VDC models only. — 5982 Die cast terminal box for 30R motors and gearmotors F 0992 Adaptor plate for mounting brakes or encoders for 33A/42A gearmotors/motors with accy. ready shaft extensions G 0993 Adaptor plate for mounting brakes or encoders for 22B/34B gearmotors/motors with accy. ready shaft extensions H 0995 3-hole adaptor plate for E, F, WX and FX gearmotors. Provides drop-in replacement for competitive gearmotors. I 0991 Die cast base kit for 42A motors and gearmotors J 0996 Base kit for 34R motors and gearmotors K 0960 Mounting Flange for 60P planetary gearmotors (U.S.) L 0961 Mounting Flange for 60P planetary gearmotors (Metric) M 0962 IP-66 Seal Kit for 60P planetary gearmotors (U.S.) N 0963 IP-66 Seal Kit for 60P planetary gearmotors (Metric) O 0958 Base Mount Kit for 5L/H Hollow Shaft Gearmotors

30°

45°

IF, G

Box-Type Capacitor

Metal Can-Type Capacitor

Capacitors

A, B

Select a run capacitor based on the speciﬁ cations found on pages 4-21 (29-33 for metric models) and in the tables below. The AC gearmotor or motor nameplate states the required capacitance of the run capacitor, but it is also critical to specify a capacitor that has the voltage ratings as shown in these tables. When using a run capacitor that is not supplied by Bodine Electric, please make sure the voltage rating is equal to or higher than the voltage rating speciﬁ ed on this page. Different motor sizes might require a different minimum voltage rating for the run capacitor.

Capacitors

49426812

49400045 49400046 49400047 49400048 49400050 49400051

0.9/250

1.0/250

1.2/250

1.3/250

1.5/250

1.6/250 49401049 0.4/440 49400091 1.3/440 49401047 2.3/250

Capacitor ﬁ ts inside terminal box kit model 0984. 2 Capacitor ﬁ ts inside oversized terminal box model number 0985.3 New capacitor part number effective 06/2016.

49401015 5.0/250 49401154 49401054 10.0/250 49401115 49401106 9.0/250 49401006 12.5/250 49401156 49401113 49401112 49401090

1, 3

4.0/250

7.5/370

6.0/450

15.0/250

20.0/250

27.5/250

30.0/250

49401123 49401068 49401107 49401075 49401057 20.0/350

49401124 25.0/370 49401145 49401147 49401148

3.75/370

5.0/400

12.5/370

15.0/350

45.0/250

40.0/250

10.0/450

Capacitor Mounting Clamps

A 54701013 Mounting clamp for round, metal can type capacitor model 49401124 B 54701029 Mounting clamp for round, metal can type capacitors: models 49401145, 49401147, and 49401148

CATALOG S

Bodine Electric Company

Item

Model No.

Description

Model No.

Description

Item

Model No.

Description

Item

Model No.

Description

Shaft Kits for type 3F/H, 5L/H and GB/H hollow shaft gearmotors

Shaft Accessories

AC | DC | BL

0910 Shaft kit for type 3F/H gearmotors, 1/2 inch diameter, single shaft 0920 Shaft kit for type 3F/H gearmotors, 1/2 inch diameter, double shaft 0912 Shaft kit for type 5L/H gearmotors, 5/8 inch diameter, single shaft 0922 Shaft kit for type 5L/H gearmotors, 5/8 inch diameter, double shaft 0917 Shaft kit for type GB/H gearmotors, 3/4 inch diameter, single shaft 0927 Shaft kit for type GB/H gearmotors, 3/4 inch diameter, double shaft 0928 Shaft Kit for type 5L/H gearmotors, 5/8 inch to 3/4-inch diameter, single shaft 0950 Cover kit for type 3F/H gearmotors 0951 Cover kit for type 5L/H and GB/H gearmotors 0955 Flange mount kit for 3F/H gearmotors 0956 Flange mount kit for 5L/H and GB/H gearmotors

Encoder Shaft Kit for type 22B4-60P planetary gearmotors

0964 Encoder Shaft Kit, 3/8 inch diameter

— 0888

— 0890

— 0893

— 0895 Switch Sealing Kit upgrades NEMA-12 brushless DC and PMDC enclosed controls to IP-44 rating.

A 3981 Cable Kit for stock 34B/FV INTEGRAmotors. Length: six feet (3 cables: power, logic and encoder).

B 3982

C 3983

D 3984

— 43300260

— 43300270

Analog Interface Board for use with model 0810, 0830, and 0850 controls. Allows control to accept a variable voltage or current signal from user’s host controller to automatically control motor speed. Inputs are optically isolated. Electronic Direction and Braking Board, F-B-R Kit, for use with model 0810, 0830, and 0850 controls. Allows user to change motor direction and to dynamically brake motor to a quick stop. Inputs are not optically isolated. This kit includes one F-B-R board, one cable and connector, mounting hardware, and two additional braking resistors. Local/Remote Switch for use with model 0810, 0830, and 0850 controls when used with accessory model 0888. Allows user to switch between automatic and manual operation.

Extension Cable for model 3910, 3911, 3921 and 3912 controls. Extends the cable between the motor and control by six feet. Both ends are equipped with circular connections for easy connection between model 3983 cable assembly or encased control and the motor. Length: six feet. Connection Cable Assembly for connecting model 3910, 3921 and 3911 chassis controls to stock 130 V motors. One end of the cable is equipped with a circular connector, the other end is equipped with quick disconnects for phase leads, and a molded connector for the commutation leads. Length: 6 feet. Analog Interface And Isolation Module for model 3910, 3911,3921 and 3912 controls. Provides Analog interface and isolates controls from system controller input signals which may be at different potentials. Speed Potentiometer Kit for use with FPM controls. Contains 10k Ohm potentiometer, hardware, wire and connector for manually regulating motor speed. Fuse and Speed Potentiometer Kit for use with model 3910 control. Contains potentiometer for manually regulating motor speed and various fuses to cover the range of motors and gearmotors which can be used with the control.

Cover kits type 3F/H (left), types 5L/H and GB/H (right)

Flange mount kits type 3F/H (left), types 5L/H and GB/H (right)

Encoder Shaft Kit

Control Accessories

BLDC | PMDC

A B

Metric “L” Brackets

A 0990 Metric Kit for 24A B 1968 Metric Kit for 33A motors, and type D and Z gearmotors C 1970 Metric Kit for type W gearmotors D 1969 Metric Kit for E, F and FX gearmotors (will not ﬁ t 48R-F or 48R-FX)

— — no “L” bracket kits are available for 34R and 34R-Z gearmotors

Metric Motor and Gearmotor Kits

E 1982 Metric die cast terminal box kit for 30R motors and gearmotors

E 1984

Metric die cast terminal kit with terminal block for 33A, 34R, 42A and 42R motors and gearmotors.

For 90/130, 130V and 180VDC models only.

EDC

Metric Accessories

CATALOG S

AC | DC