Page 1
BMW Parts and Accessories
Installation Instructions
5
3
1
R
4
2
F 39 0961 B
Basic hands-free retrofit kit for upgrading various mobile phones
(system without switch module)
BMW 5 Series Saloon (E
BMW 5 Series touring (E
without telephone preparation (SA640)
Technical and electrical knowledge required.
The installation time is 2 -3 hours but this may vary depending on the condition of the car and
the equipment in it.
Retrofit/Installation kit No. 84 64 0 025 805
39) LHD
39/2) LHD
84 64 0 025 806
84 64 0 025 807
84 64 0 025 808
84 64 0 025 809
84 64 0 025 866
84 64 0 025 867
84 64 0 025 868
84 64 0 025 869
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
Page 2
Contents
Section Page
1. Important information for the installation of the basic kit . . . . . . . . . . . . . . . . . . . . . 3
2. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. Installation and cabling diagram for basic wiring harness A in E39 cars. . . . . . . . . . 8
6. Installation and cabling diagram for basic wiring harness A
and power supply wiring harness B in E39/2 cars . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. To prepare the installation site for the microphone in cars without a sunroof. . . . . . 10
8. To prepare the installation site for the microphone in cars with a sunroof . . . . . . . . 11
9. To install the basic wiring harness A in E39 cars . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10. To install the basic wiring harness A and power supply wiring harness B
in E39/2 cars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12. Circuit diagram for the basic wiring harness A in E39 cars . . . . . . . . . . . . . . . . . . . 32
13. Circuit diagram for the basic wiring harness A in E39/2 cars . . . . . . . . . . . . . . . . . . 34
14. Circuit diagram for the power supply wiring harness B in E39/2 cars . . . . . . . . . . . 36
15. Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
Page 3
1. Important information for the installation of the basic kit
Only for use in the BMW dealer organisation.
The basic kit may only be installed by a specialist workshop that has the required special tools
and manuals (servicing, repair, diagnostics, etc.).
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
Additional cables/lines that you install must be secured with cable ties/textile adhesive tape.
If the specified PIN's and chambers are occupied, bridges, double crimps or twin-lead terminals
must be used.
Item numbers refer only to the overview drawings and to the texts next to the appropriate figure.
The hands-free kit is only active if the ignition key is turned to position 1 (terminal R) or
further (from ignition key position 1 the telephone ON signal is simulated on the radio).
The radio then sends the telephone signals to the on-board speakers.
"
The interior trim parts supplied in the trim colour black are also available in other trim
colours and can be ordered using the electronic parts catalogue (EPC).
"
These installation instructions are only valid for cars
- without an on-board monitor radio with a production date after 9/00 or
- with an on-board monitor radio with a production date after 10/01.
"
The power supply wiring harness B is only required for BMW 5 Series touring (E39/2)
LHD cars.
"
Subject to technical modifications
Tools and requirement required
MoDIC III or DIS Cable lamp
Set of Philips screwdrivers Sharp knife
Set of flat screwdrivers Set of drill bits 1 – 10 mm
1/4 inch socket set Drill
Set of Torx sockets Textile adhesive tape
Angle cutter Step drill, diameter 30 mm
Combination pliers
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/3
Page 4
2. Preparations
TIS
instruction
No.
Conduct a brief test (print out error memory) Disconnect the battery 12 00...
Remove the radio (cars without an on-board monitor radio only) 65 11 030
Remove the heater/air conditioning control 64 11 749
Remove the cover on the gearshift lever. 51 16 210
Remove the base of the centre console 51 16 200
Remove the driver’s seat 52 13 000
Remove the rear seat bench 52 24 005
Remove the rear seat backrest (cars without a split rear seat backrest only) 52 24 010
Remove the side pad on the left (cars with a split rear seat backrest only) Remove the front left door sill trim 51 47 000
Remove the rear left door sill trim 51 47 030
Remove the footwell trim on the driver’s side 51 45 030
Remove the side footwell trim on the left A pillar Remove the left A pillar trim (refer to instructions for head airbag) 51 43 201
Remove the left sun visor 51 16 080
Lower the front headlining slightly Remove the cover on cars with a glass slide/tilt sunroof 51 44 011
Remove the left boot / wheel arch trim. 51 47 101
Remove the CD changer (if fitted) 65 11 070
Remove the audio amplifier (if fitted) 65 12 070
Remove the navigation computer (if fitted) 65 90 510
Also on E39 cars
Remove the video module (if fitted) 65 50 510
Also on E39/2 cars
Remove the combination roller blind (if fitted) Remove the boot floor 51 47 101
Remove the spare wheel cover 51 47 131
Remove the spare wheel Remove the cover on the on-board monitor radio 65 52 520
Remove the tool holder Remove the right boot / wheel arch trim. 51 47 101
Remove the rear boot floor supports on both sides 65 11 055
Remove the front boot floor supports on both sides 65 11 055
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/4
Page 5
3. Parts list
0
5A
A
E 39
3
9
4
10 1312
5 7
B
11
1
6
2
8
F 39 0962 B
A Basic wiring harness
B Power supply wiring harness (E39/2 cars only)
1 Insulation-piercing connector (2-way)
2 5A fuse
3 Cable tie (15x)
4 FME connector
5 Template for microphone holder for E39 and E39/2 cars without a sunroof
6 Black microphone cover (only for cars without a sunroof)*
7 Black frame for hands-free kit (only for cars without a sunroof)*
8 Sub-frame for hands-free kit (only for cars without a sunroof)*
9 Front black roof liner trim panel (only for cars with a sunroof)*
10 Black microphone cover (only for cars with a sunroof)*
11 Hexagonal screw with collar
12 Washer, diameter 6.3 mm
13 Nut with collar (x2)
Parts marked with an asterisk (*) are supplied with the retrofit kit in black and may be ordered
separately in other trim colours using the electronic parts catalogue (EPC).
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/5
Page 6
4. Connection overview
0
A7
A6
A15
A8
A9
A10
1
F 39 0963 B
A11
A12
A13
A
A1
A14
A2
A5
A4
1
A3
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/6
Page 7
4. Connection overview
A1
A2
A3
A4
A5
A6
A7
A8
A9
Item Description
A Basic wiring harness
Coaxial socket casing FME - To coaxial plug casing FME on the required load holder
Black 12-pin plug connector -
Socket contact
Signal: Mute
Black 18-pin socket casing
Black 3-pin socket casing
Black 3-pin socket casing
Coaxial socket casing FME
Floating fuse
Signal: Terminal 30
Black 12-pin plug connector
A10
A11
Socket contact
Signal: Mute
Cable eyelet, 6 mm in diameter
Signal: Terminal 31
Cable
colour
-
with the hands-free kit or to the required adapter
Cars without an on-board monitor radio only:
To radio connection plug (after disconnecting the black
12-pin plug casing X13598 from the radio connection plug
Cars with an on-board monitor radio only:
Tie back (no longer required)
white/brown Cars without an on-board monitor radio and without
an existing mute cable on the radio connection plug
only:
To radio connection plug PIN10 , in the 8-pin plug casing
X18126
Cars without an on-board monitor radio and with an
existing mute cable on the radio connection plug
only:
Cut off, connect to the supply cable of the radio connection
plug PIN10 , white/brown cable, in the 8-pin plug casing
X18126 using a 2-way insulation-piercing connector (1)
Cars with an on-board monitor radio only:
Tie back (no longer required)
---
---
---
---
red To the standard wiring harness near the left tail light
---
white/brown Cars without an on-board monitor radio only:
brown in E39 cars to the earth post X10305
To the adapter cable required for the hands-free kit,
behind the rear module holder
To the microphone required for the hands-free kit, in the
headlining
To cable compensator in the boot on the left if the car is
fitted with a cable compensator (if not, insulate and tie back)
To the coaxial plug casing FME on the FME connector (4)
in the boot on the left (connection for telephone aerial); if
you are upgrading the car with a cable compensator, to
the cable compensator or to the required adapter
Cars without an on-board monitor radio only:
Tie back (no longer required)
Cars with an on-board monitor radio only:
To radio connection plug (after disconnecting the black
12-pin plug casing X13598 from the radio connection
plug)
Tie back (no longer required)
Cars with an on-board monitor radio and without an
existing mute cable on the radio connection plug
only:
To radio connection plug PIN10 , in the 8-pin plug casing
X18126
Cars with an on-board monitor radio and with an
existing mute cable on the radio connection plug
only:
Cut off, connect to the supply cable of the on-board
monitor radio connection plug PIN10 , white/brown
cable, in the 8-pin plug casing X18126 using a 2-way
insulation-piercing connector (1)
in E39/2 cars to the earth post X13016
Connection location in the car
----
)
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/7
Page 8
4. Connection overview
Item Description
A12
A13
A14
A15
White 12-pin plug casing
White 12-pin socket casing
Socket contact
Signal: TEL ON
Socket contact
Signal: TEL ON
Cable
colour
E39 cars only:
To the white 12-pin socket casing X322 , in the boot on
---
---
white/green Cars without an on-board monitor radio and without
white/green Cars without an on-board monitor radio only:
the left
E39/2 cars only:
To branch B1 , white 12-pin socket casing on the power
supply wiring harness B in the boot on the left
E39 cars only:
To the white 12-pin plug casing X322 , in the boot on the
left
E39/2 cars only:
Tie back (no longer required)
an existing TEL ON cable on the radio connection
plug only:
To radio connection plug PIN11 , in the 8-pin plug casing
X18126
Cars without an on-board monitor radio and with an
existing TEL ON cable on the radio connection plug
only:
Cut off, connect to the supply cable of the radio
connection plug PIN11 , white/green cable, in the 8-pin
plug casing X18126 using a 2-way insulation-piercing
connector (1)
Cars with an on-board monitor radio only:
Tie back (no longer required)
Tie back (no longer required)
Cars with an on-board monitor radio and without an
existing TEL ON cable on the radio connection plug
only:
To radio connection plug PIN11 , in the 8-pin plug casing
X18126
Cars with an on-board monitor radio and with an
existing TEL ON cable on the radio connection plug
only:
Cut off, connect to the supply cable of the on-board
monitor radio connection plug PIN11 , white/green cable,
in the 8-pin plug casing X18126 using a 2-way
insulation-piercing connector (1)
Connection location in the car
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/8
Page 9
4. Connection overview
Power supply wiring harness B for BMW 5 Series touring (E39/2) LHD cars
B4
B
B1
B1
B3
1
B2
Item Description
B Power supply wiring harness
White 12-pin socket casing
B2 Open cable end grey/red To the supply cable for the black 12-pin plug connector
B3 Black 2-pin socket casing
B4 Black 2-pin plug casing
Cable
colour
--- ----
BMW 5 Series touring (E39/2) cars only
---
---
---
To branch A12, on the basis wiring harness A in the boot
on the left
X322 PIN5, grey/red cable, in the boot on the left using
a 2-way insulation-piercing connector (1)
To the black 2-pin plug casing on plug connector X325,
in the boot on the right above the power distributor
To the black 2-pin socket casing on plug connector
X325, in the boot on the right above the power
distributor
Connection location in the car
F 39 0964 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/9
Page 10
5. Installation and cabling diagram for basic wiring harness A in E39 cars
A3
Punkt 1
0
A1
Punkt 1
A2+A3
A14
A4
A
A6+A7
A12+A13
A5
A15
The basic wiring harness A is to be installed along the audio and main wiring harness as shown
in the figure and secured using textile adhesive tape and cable ties.
Start the installation of the basic wiring harness A at point 1 (next to the handbrake lever)
with branches A1 to A4.
A8-A11
F 39 0965 B
Branch A1 to the footwell on the right
Branches A2, A3 and A14 to the installation site of the radio (insulate and tie back in cars with
an on-board monitor radio)
Branch A4 next to the gearshift lever on the left (under the oddments box in the centre console
at the front)
Branch A5 to the installation site of the microphone in the headlining at the front centre
Branch A6 to the installation site of the compensator in the boot on the left
Branch A7 to the installation site of the compensator in the boot on the left or to the connector
for the telephone aerial in the boot on the left
Branch A8 to the left tail light wiring harness
Branches A9, A10 and A15 to the on-board monitor radio in the boot on the left (insulate and
tie back in cars without an on-board monitor radio)
Branch A11 to earth post X10305 under the left tail light
Branch A12 to plug connector X322 in the boot on the left
Branch A13 to plug connector X322 in the boot on the left
Tie back any excess lengths.
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/10
Page 11
6. Installation and cabling diagram for basic wiring harness A and power supply
A3
Punkt 1
wiring harness B in E39/2 cars
0
B3
B4
A1
Punkt 1
B
A2+A3
A14
A5
A4
A9+A10
A6+A7
B1
A12+A13
A
The basic wiring harness A is to be installed along the audio and main wiring harness as shown
in the figure and secured using textile adhesive tape and cable ties.
Start the installation of the basic wiring harness A at point 1 (next to the handbrake lever)
with branches A1 to A4.
Branch A1 to the footwell on the right
Branches A2, A3 and A14 to the installation site of the radio (insulate and tie back in cars with
an on-board monitor radio)
Branch A4 next to the gearshift lever on the left (under the oddments box in the centre console
at the front)
Branch A5 to the installation site of the microphone in the headlining at the front centre
Branch A6 to the installation site of the compensator in the boot on the left
Branch A7 to the installation site of the compensator in the boot on the left or to the connector
for the telephone aerial in the boot on the left
Branch A8 to the left tail light wiring harness
Branches A9, A10 and A15 to the on-board monitor radio in the boot on the left (insulate and
tie back in cars without an on-board monitor radio)
Branch A11 to earth post X13016 under the left tail light
Branch A12 to branch B1 on the power supply wiring harness B in the boot on the left
Branch A13 - insulate and tie back
B2
A15
A8+A11
F 39 0966 B
Power supply wiring harness B
Branch B1 to branch A12 on the basic wiring harness A in the boot on the left
Branch B2 to plug connector X322 in the boot on the left
Branch B3 to plug connector X325 in the boot on the right above the power distributor
Branch B4 to plug connector X325 in the boot on the right above the power distributor
Tie back any excess lengths.
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/11
Page 12
7. To prepare the installation site for the microphone in cars without a sunroof
0
Take the required template out of the retrofit kit
and cut it out.
Then place the required template against the rear
22
external contour of the interior light (20) and affix it
to the headlining (21).
Cut out the required opening (22) with a sharp
knife.
As you cut out the material ensure that you
do not damage any cables/leads.
"
Remove the template again.
Push the hands-free kit sub-frame (8) through the
opening (20) into the headlining (21).
21
21
E39
20
F 39 0967 B
0
20
Insert the hands-free kit frame (7) into the opening
(20) and clip the hands-free kit sub-frame (8) to the
hands-free kit frame (7).
8
Secure the microphone trim (6) in the hands-free
kit frame (7).
7
.
6
F 39 0968 B
0
0
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/12
Page 13
8. To prepare the installation site for the microphone in cars with a sunroof
0
Take the existing front headlining trim off the
headlining and remove the switch (20) for the glass
tilt/slide sunroof.
Discard the existing front headlining trim and
replace it with the new front headlining trim (9).
Secure the microphone trim (10) and the switch
(20) for the glass tilt/slide sunroof in the new front
headlining trim (9).
Then fit the new front headlining trim (9) back into
the headlining.
9
10
20
F 39 0969 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/13
Page 14
9. To install the basic wiring harness A (E39 cars only)
0
The figure shows the installation space near
21
the handbrake lever.
"
A1-A4+A14
A
20
A4
A14
A
A2
A3
F 39 0971 B
20
A1
F 39 0972 B
20
22
21
Carefully cut out the opening (20) in the carpet (21)
in front of the handbrake lever (22).
Pull up the carpet at the rear (21) on the driver’s
side and lay branches A1 to A4 and A14 on the
basic wiring harness A forwards to the gearshift
lever under the centre console.
0
Lay branch A1, coaxial socket casing FME on the
basic wiring harness A under the centre console
(20) into the passenger’s footwell.
Lay branch A4, black 18-pin socket casing on the
basic wiring harness A, as shown in the figure,
under the centre console oddments box at the
front.
Connect branch A4 to the required adapter
cable for the hands-free kit.
0
In cars with an on-board monitor radio,
insulate and tie back branches A2, A3 and
A14.
"
Lay branch A2, black 12-pin plug casing, branch
A3, socket contact, white/brown cable, and
branch A14, socket contact, white/green cable, on
the basic wiring harness A to the installation site of
the radio.
"
A
F 39 0976 B
X13598
21
A2
20
20
A2
F 39 0973 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
0
Cars without an on-board monitor radio only
Disconnect the black 12-pin plug casing X13598
from the radio connection plug (20) and tie it back.
Connect branch A2, black 12-pin plug casing, to
the cleared slot (21) in the radio connection plug
(20).
If the car does not have a black 12-pin plug
casing X13598, branch A2 must be
connected direct.
"
EN/14
Page 15
9. To install the basic wiring harness A (E39 cars only)
0
This step only applies to cars without an
existing mute cable on the radio connection
X18126/PIN10
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
20
20
A3
A3
21
A
X18126
1
20
F 39 0974 B
20
F 39 0975 B
Connect branch A3, socket contact, white/brown
cable, to the free slot in the radio connection plug
(20) PIN10 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the radio connection plug (20).
Cut off the basic wiring harness A near branch A3.
Connect branch A3, white/brown cable, to the
supply cable of the radio connection plug (20)
PIN10, white/brown cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
"
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/15
Page 16
9. To install the basic wiring harness A (E39 cars only)
I
I
I
I
I
I
0
Cars without an on-board monitor radio only
20
20
X18126/PIN11
A14
A
A14
X18126
1
21
20
039 0001 B
20
039 0002 B
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Connect branch A14, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Cut off the basic wiring harness A near branch
A14.
Connect branch A14, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0
Applies to all E39 cars
21
A
20
A
The figure shows the area with the removed
driver’s seat.
"
Pull up the driver's side carpet at the rear (20) and
lay the basic wiring harness A as shown in the
figure and secure it with textile adhesive tape (21).
Lay branch A5, black 3-pin socket casing, along
21
the left door sill towards the front.
A5
F 39 0977 B
A5
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
F 39 0981 B
0
Thread branch A5, black 3-pin socket casing on
the basic wiring harness A near the left A pillar
through the instrument panel from below and
along the left A pillar upwards to the headlining
and secure it with textile adhesive tape.
!
As you lay branch A5 to the microphone
installation site, ensure that the cable is
properly routed in the cable duct to prevent
any impairment of the head airbag
function.
!
See instructions for head airbag."
"
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/16
Page 17
9. To install the basic wiring harness A (E39 cars only)
0
The figure shows the boot on the left."
A6
Thread the basic wiring harness A with branches
3
A7
20
A
A6 to A13 and A15, as shown in the figure, through
the passage grommet (20) along the standard
wiring harness to the boot and secure it with cable
ties (3).
A8
A11
A12
A13
A9
A10
A15
F 39 0978 B
0
Disconnect the white 12-pin plug connector X322.
X322S
4
A6
A7
A13
A12
A
X322B
F 39 0979 B
Insert branch A12, white 12-pin plug casing, and
branch A13, white 12-pin socket casing on the
basic wiring harness between the above
connectors.
Secure the new plug connectors A13+X322S and
A12+X322B, as shown in the figure.
0
Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them if necessary.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
F 39 0980 B
0
Cars without an on-board monitor radio only
Insulate branch A9, black 12-pin plug casing,
A
A10
A9
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
A15
F 39 0982 B
branch A10, socket contact, white/brown cable,
and branch A15, socket contact, white/green
cable, on the basic wiring harness A and tie them
back on the standard wiring harness.
Branches A9, A10 and A15 are no longer
required.
"
EN/17
Page 18
9. To install the basic wiring harness A (E39 cars only)
0
X13598
Cars with an on-board monitor radio only
20
20
A9
21
20
F 39 0983 B
X18126/PIN10
20
A10
Disconnect the black 12-pin plug casing X13598
from the on-board monitor radio connection plug
(20) and tie it back.
Connect branch A9, black 12-pin plug casing, into
the cleared slot (21) in the on-board monitor radio
connection plug (20).
If the car does not have a black 12-pin plug
casing X13598, branch A9 must be
connected direct.
0
This step only applies to cars without an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10 of
the 8-pin plug casing X18126.3
Connect branch A10, socket contact, white/brown
cable, to the free slot in the on-board monitor radio
connection plug (20) PIN10 on the 8-pin plug
casing X18126.
"
20
A10
1
21
F 39 0985 B
X18126
20
F 39 0986 B
0
This step only applies to cars with an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10
of the 8-pin plug casing X18126.3
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the on-board monitor radio connection plug (20).
Cut off the basic wiring harness A near branch
A10.
Connect branch A10, socket contact, white/brown
cable, to the supply cable of the on-board monitor
radio connection plug (20) PIN10, white/brown
cable, on the 8-pin plug casing X18126 using a
2-way insulation-piercing connector (1).
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/18
Page 19
9. To install the basic wiring harness A (E39 cars only)
0
Cars with an on-board monitor radio only
X18126/PIN11
20
20
A15
21
039 0003 B
A15
1
X18126
20
039 0004 B
20
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
Connect branch A15, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin
plug casing X18126.
Cut off the basic wiring harness A near branch
A15.
Connect branch A15, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0
Only required for cars without earth post
X10305 with a production date after 9/00
"
"
22
21
A
21
B
20
F 39 0992 B
Remove the left tail light.
Mark the drilling position (20) with a centre punch.
Dimension A= 19 mm
Dimension B = 17 mm
Remove the body paint and primer from the grey
area (21) in a diameter of 20 mm around the
position of the hole (20) on the front and rear of the
tail light unit (22).
The panel must be bare in the grey area (21), to
ensure that perfect contact is possible.
Risk of damage. Before drilling the hole
ensure that the cable and plug fastenings are
unclipped and the cables are removed from
the drilling area to prevent their being
damaged.
Drill the holes with a 6 mm drill bit.
Remove all the drill chips that are produced during
the drilling process using an extractor.
Then deburr the edges of the hole.
"
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/19
Page 20
9. To install the basic wiring harness A (E39 cars only)
0
Insert the hexagonal screw with collar (11) from the
rear into the hole (20) and secure it with a nut M6
(13).
20
If you fit the earth connection cable later, ensure
that you fit the washer (12) first and then branch
11
13
12
13
A11.
Then secure branch A11 (the cable outlet on the
terminal lug must point downwards) with the
second nut M6 (13).
5A
A11
2
F 39 0993 B
20
F 39 0994 B
After securing the parts, treat all of them with
the anti-corrosion measures set out in the
BMW standard.
0
"
The figure shows the final installation position
of the earth connection cable.
"
The cable loom (20) must point downwards.
0
Applies to all E39 cars
Remove the left tail light.
Mark the drilling position (20) with a centre punch.
A8
3
F 39 0984 B
The figure shows the left lamp holder, on cars
without a lamp holder proceed in exactly
the same way.
"
Insert the 5A fuse (2) into the fuse holder A8.
Secure the fuse holder A8 to the wiring harness
near the left tail light with a cable tie (3).
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/20
Page 21
10. To install the basic wiring harness A and power supply harness BE39/2 cars
only
0
The figure shows the installation space near
21
the handbrake lever.
"
A1-A4+A14
A
20
A
A4
A14
A2
A3
F 39 0971 B
20
A1
F 39 0972 B
20
22
21
Carefully cut out the opening (20) in the carpet (21)
in front of the handbrake lever (22).
Pull up the carpet at the rear (21) on the driver’s
side and lay branches A1 to A4 and A14 on the
basic wiring harness A forwards to the gearshift
lever under the centre console.
0
Lay branch A1, coaxial socket casing FME on the
basic wiring harness A under the centre console
(20) into the passenger’s footwell.
Lay branch A4, black 18-pin socket casing on the
basic wiring harness A, as shown in the figure,
under the centre console oddments box at the
front.
Connect branch A4 to the required adapter
cable for the hands-free kit.
0
In cars with an on-board monitor radio,
insulate and tie back branches A2, A3 and
A14.
"
Lay branch A2, black 12-pin plug casing, branch
A3, socket contact, white/brown cable, and
branch A14, socket contact, white/green cable, on
the basic wiring harness A to the installation site of
the radio.
"
A
F 39 0976 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/21
Page 22
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
Cars without an on-board monitor radio only
A2
20
20
X13598
21
A2
F 39 0973 B
X18126/PIN10
A3
20
20
Disconnect the black 12-pin plug casing X13598
from the radio connection plug (20) and tie it back.
Connect branch A2, black 12-pin plug casing, to
the cleared slot (21) in the radio connection plug
(20).
If the car does not have a black 12-pin plug
casing X13598, branch A2 must be
connected direct.
0
This step only applies to cars without an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
Connect branch A3, socket contact, white/brown
cable, to the free slot in the radio connection plug
(20) PIN10 on the 8-pin plug casing X18126.
"
"
20
A3
21
A
X18126
1
F 39 0974 B
20
F 39 0975 B
0
This step only applies to cars with an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the radio connection plug (20).
Cut off the basic wiring harness A near branch A3.
Connect branch A3, white/brown cable, to the
supply cable of the radio connection plug (20)
PIN10, white/brown cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
"
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/22
Page 23
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
I
I
I
I
I
I
0
Cars without an on-board monitor radio only
20
20
X18126/PIN11
A14
A
A14
X18126
1
21
20
039 0001 B
20
039 0002 B
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Connect branch A14, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.3
Cut off the basic wiring harness A near branch
A14.
Connect branch A14, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0
Applies to all E39/2 cars
21
A
20
A
The figure shows the area with the removed
driver’s seat.
"
Pull up the driver's side carpet at the rear (20) and
lay the basic wiring harness A as shown in the
figure and secure it with textile adhesive tape (21).
Lay branch A5, black 3-pin socket casing, along
21
the left door sill towards the front.
A5
F 39 0977 B
A5
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
F 39 0981 B
0
Thread branch A5, black 3-pin socket casing on
the basic wiring harness A near the left A pillar
through the instrument panel from below and
along the left A pillar upwards to the headlining
and secure it with textile adhesive tape.
!
As you lay branch A5 to the microphone
installation site, ensure that the cable is
properly routed in the cable duct to prevent
any impairment of the head airbag
function.
!
See instructions for head airbag."
"
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/23
Page 24
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
The figure shows the boot on the left."
A9
A8
A10
A11
A12
A15
A13
A7
A6
A7
A6
3
F 39 0997 B
4
Lay the basic wiring harness A, as shown in the
figure, with branches A6 to A13 and A15 along the
standard wiring harness and secure it with cable
ties (3).
0
Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
B
B1
A12
A
A13
F 39 0998 B
F 39 0999 B
0
Connect branch A12, white 12-pin plug casing
on the basic wiring harness A to branch B1, white
12-pin socket casing on the power supply wiring
harness B.
Tie back plug connector A12 + B1 on the standard
wiring harness.
0
Insulate branch A13, white 12-pin socket casing
and tie it back on the standard wiring harness (no
longer required).
F 39 1000 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/24
Page 25
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
Carefully cut open the sheathing of the audio
B2
wiring harness (20) for a length of 100 mm behind
the black plug connector X322.
Connect branch B2, open cable end, grey/red
1
20
cable, to the supply cable, grey/red cable, of the
black 12-pin plug connector X322 PIN5 using a
2-way insulation-piercing connector (1).
20
1
B
3
X322
20
B3
B4
X325
F 39 1001 B
0
Lay branch B3 and branch B4 on the power supply
wiring harness B along the standard wiring
harness (20) to the tied back black 2-pin plug
connector X325 above the power distributor in the
boot on the right.
Secure the power supply wiring harness B to the
standard wiring harness (20) using cable ties (3).
X325S
B
X325S
20
B3
B3
B
o
o
o
o
o
o
o
o
o
20
o
o
o
o
o
o
o
o
o
F 39 1002 B
0
Connect branch B3, black 2-pin socket casing
on the power supply wiring harness B to the black
2-pin plug casing X325S.
B4
Connect branch B4, black 2-pin plug casing on
the power supply wiring harness B to the black
2-pin socket casing X325B.
X325B
F 39 1003 B
0
Tie back plug connectors X325S+B3 and
X325B+B4 on the standard wiring harness (20)
with cable ties.
B4
When securing the connections, make sure
that the cable harnesses will not be damaged
X325B
during the subsequent assembly of the
car.
"
F 39 1004 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/25
Page 26
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
The figure shows the boot on the left."
X13016
X13598
A11
A
A9+A10+A15
F 39 1005 B
F 39 1044 B
Secure branch A11, cable eyelet with a diameter
of 6 mm, brown cable, to earth post X13016 under
the left tail light.
0
In cars without an on-board monitor radio,
insulate and tie back branches A9, A10 and
A15.
"
Lay branch A9, black 12-pin plug casing, branch
A10, socket contact, white/brown cable, and
branch A15, socket contact, white/green cable, on
the basic wiring harness A to the installation site of
the on-board monitor radio.
0
Cars with an on-board monitor radio only
Disconnect the black 12-pin plug casing X13598
from the radio connection plug (20) and tie it back.
21
20
X18126/PIN10
A10
A9
20
20
F 39 1009 B
20
F 39 1010 B
Connect branch A9, black 12-pin plug casing, into
the cleared slot (21) in the on-board monitor radio
connection plug (20).
If the car does not have a black 12-pin plug
casing X13598, branch A9 must be
connected direct.
0
"
This step only applies to cars without an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10
of the 8-pin plug casing X18126.3
Connect branch A10, socket contact, white/brown
cable, to the free slot in the on-board monitor radio
connection plug (20) PIN10 on the 8-pin plug
casing X18126.
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/26
Page 27
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
1
21
A10
X18126
20
This step only applies to cars with an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10 of the
8-pin plug casing X18126.3
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the on-board monitor radio connection plug (20).
X18126/PIN11
20
A15
20
F 39 1011 B
20
039 0005 B
Cut off the basic wiring harness A near branch
A10.
Connect branch A10, socket contact, white/brown
cable, to the supply cable of the on-board monitor
radio connection plug (20) PIN10, white/brown
cable, on the 8-pin plug casing X18126 using a
2-way insulation-piercing connector (1).
0
Cars with an on-board monitor radio only
This step only applies to cars without an
existing TEL ON cable on the on-board
monitor radio connection plug (20) PIN11
of the 8-pin plug casing X18126.
Connect branch A15, socket contact, white/green
cable, to the free slot in the on-board monitor radio
connection plug (20) PIN11 on the 8-pin plug
casing X18126.
0
"
1
21
A15
X18126
20
20
039 0006 B
This step only applies to cars with an
existing TEL ON cable on the one-board
monitor radio connection plug (20) PIN11
of the 8-pin plug casing X18126.3
Cut off the basic wiring harness A near branch
A15.
Connect branch A15, socket contact, white/green
cable, to the supply cable of the on-board monitor
radio connection plug (20) PIN11, white/green
cable, on the 8-pin plug casing X18126 using a
2-way insulation-piercing connector (1).
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/27
Page 28
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
Applies to all E39/2 cars
5A
2
Insert the 5A fuse (2) into the fuse holder A8.
Secure the fuse holder A8 to the wiring harness
near the left tail light with a cable tie (3).
A8
3
F 39 1006 B
0
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/28
Page 29
11. Concluding work
Do not assemble the car again until the required hands-free retrofit kit has been installed (see
separate installation instructions).
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/29
Page 30
12. Circuit diagram for the basic wiring harness A in E39 cars
1) 2)
SCHIRM
0.5
1
A1*
1
2
A5*
3
A4*
X002*
11
14
17
2
30
31
30
31
31
ANT
WS
0.5
RT
0.5
BR
0.5
WSGN
0.35
TELE ON
TELE ON
RT
0.35
BR
0.35
BR
0.35
1.0
BR
1.0
0.35
0.35
BR
WSGN
WSBR
ANT
10
TEL ON
MUTE
1
A7*
F 39 0970 B
X13016
X003*
10
X001*
VIWS
0.35
R
WSGN
0.35
WSBR
F1*
5A
10
30
15
18
58g
MUTE
0.35
0.35
0.35
RT
GRRT
WSBR
1.0
2
RT
1
RTGN
2.5
0.35
0.35
0.35
SWBR
SWWS
X18126
116
TEL ON
10
MUTE
12
TELNF-
TELNF+
N9
X13598
3 8
TELNF-
5
TELNF+
0.35
0.35
SWBR
SWWS
0.35
0.35
SWBR
SWWS
TELNF-
612
TELNF+
X13598
13
MIK-
4
MIK+
SCHIRM
0.35
SW
0.35
MIK-
MIK+
2
1
X18507
5
1
30
2
R
58g
0.75
2.5
1.5
GRRT
RTGN
VIWS
0.75
2.5
1.5
GRRT
RTGN
VIWS
58g
30
R
5
1
2
3
TACHO A
4
I BUS
8
TELM
9
NF+
10
NF-
11
TELE
X322B
A12*
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
0.75
0.75
1.0
1.0
0.5
SWWS
WSRTGE0.75
WSBR
SWWS
SWBR
WSGN
3
TACHO A
4
I BUS
8
TELM
9
NF+
10
NF-
11
TELE
A13*
1)
X322S
EN/30
Page 31
12. Circuit diagram for the basic wiring harness A in E39 cars
Legend
F1* Floating fuse holder near the left tail light
X001* Socket contact
X002* Black 18-pin plug casing
X003* Socket contact
A1* Console aerial connector
A4* Black 18-pin socket casing
A5* Black 3-pin socket casing; cable compensator
A7* Boot aerial connector
A12* White 12-pin plug casing
A13* White 12-pin socket casing
N9 Radio
X13016 Cable eyelet, 6 mm in diameter; earth
X13598 Black 12-pin plug casing
X18126 8-pin plug casing
X18507 Black 3-pin connection plug; microphone
1) To standard wiring harness
2) To hands-free system wiring harness
The components and X designations marked with an asterisk (*) are only valid for this circuit
diagram.
All the other components and X designations correspond to BMW after-sales circuit diagrams
Colour abbreviations
BL = Blue OR = Orange
BR = Brown OR = Orange
GE = Yellow SW = Black
GN = Green VI = Violet
GR = Grey WS = White
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/31
Page 32
13. Circuit diagram for the basic wiring harness A in E39/2 cars
SCHIRM
0.5
1
A1*
1
2
A5*
3
A4*
X002*
11
14
17
2
30
31
30
31
31
ANT
WS
0.5
RT
0.5
BR
0.5
WSGN
0.35
TELE ON
TELE ON
RT
0.35
BR
0.35
BR
0.35
1.0
BR
1.0
0.35
0.35
BR
WSGN
WSBR
ANT
TEL ON
MUTE
1
A7*
F 39 1045 B
X13016
10
X003*
10
X001*
VIWS
0.35
R
WSGN
0.35
WSBR
F1*
5A
10
15
18
3 8
5
30
58g
MUTE
TELNF-
TELNF+
0.35
0.35
0.35
RT
GRRT
WSBR
1.0
2
RT
1
RTGN
2.5
SWBR
0.35
SWWS
0.35
0.35
0.35
0.35
0.35
0.35
SWBR
SWWS
SWBR
SWWS
X18126X13598
11
TEL ON
106
MUTE
12
TELNF-
TELNF+
N9
TELNF-
612
TELNF+
X13598
13
MIK-
4
MIK+
SCHIRM
0.35
SW
0.35
MIK-
MIK+
2
1
X185073)
5
1
2
R
GRRT
0.75
58g
RTGN
2.5
30
VIWS
1.5
0.75
2.5
1.5
GRRT
RTGN
VIWS
58g
30
R
5
1
2
3
TACHO A
4
8
9
10
11
B1*
A12*
I BUS
TELM
NF+
NF-
TELE
1) 2)
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
SWWS
0.75
WSRTGE0.75
WSBR
0.75
SWWS
1.0
SWBR
1.0
WSGN
0.5
3
TACHO A
4
I BUS
8
TELM
9
NF+
10
NF-
11
TELE
A13*
EN/32
Page 33
13. Circuit diagram for the basic wiring harness A in E39/2 cars
Legend
F1* Floating fuse holder near the left tail light
X001* Socket contact
X002* Black 18-pin plug casing
X003* Socket contact
A1* Console aerial connector
A4* Black 18-pin socket casing
A5* Black 3-pin socket casing; cable compensator
A7* Boot aerial connector
A12* White 12-pin plug casing
A13* White 12-pin socket casing
N9 Radio
X322 Black, 12-pin plug connector; audio hi-fi
X13016 Cable eyelet, 6 mm in diameter; earth
X13598 Black 12-pin plug casing
X18126 8-pin plug casing
X18507 Black 3-pin connection plug; microphone
1) To power supply wiring harness B
2) To hands-free system wiring harness
3) To be tied back on the standard wiring harness
The components and X designations marked with an asterisk (*) are only valid for this circuit
diagram.
All the other components and X designations correspond to BMW after-sales circuit diagrams
Colour abbreviations
BL = Blue OR = Orange
BR = Brown OR = Orange
GE = Yellow SW = Black
GN = Green VI = Violet
GR = Grey WS = White
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/33
Page 34
14. Circuit diagram for the power supply wiring harness B in E39/2 cars
1
KL.30
2.5
RTGN
1)
X325B
2
KL.R
1.5
VIWS
KL.R
1.5
VIWS
2)
KL.30
2.5
RTGN
512
58G
0.75
GRRT
A12*
B1*B4*
2.5
RTGN
KL.30
1
1.5
VIWS
KL.R
B2*
2
B3*
X325S
1)
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
F 39 1007 B
EN/34
Page 35
14. Circuit diagram for the power supply wiring harness B in E39/2 cars
Legend
A12* White 12-pin plug casing
B1* White 12-pin socket casing
B2* Open cable end; connect cable to supply cable X322 PIN5using a 2-way
insulation-piercing connector (1)
B3* Black 2-pin socket casing
B4* Black 2-pin plug casing
X325B Black 2-pin socket casing
X325S Black 2-pin plug casing
1) To standard wiring harness
2) To basic wiring harness A
The components and X designations marked with an asterisk (*) are only valid for this circuit
diagram.
All the other components and X designations correspond to BMW after-sales circuit diagrams
Colour abbreviations
BL = Blue OR = Orange
BR = Brown OR = Orange
GE = Yellow SW = Black
GN = Green VI = Violet
GR = Grey WS = White
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/35
Page 36
15. Template
!
The original template is supplied in the parts kit."
0
E 39
F 39 1008 B
Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
EN/36
Loading...