BMW 228i Coupe, 428i Convertible, 428i xDrive Coupe, 435i Convertible, 435i Coupe, 428i Coupe, 435i xDrive Coupe, 640i Gran Coupe, 650i Gran Coupe, 650i xDrive Gran Coupe, M235i Coupe, Z4 sDrive28i Service and Warranty Information
Service and
Warranty
Information
2014
2 Series, 4 Series,
6 Series & Z4
The Ultimate
Driving Machine
®
Owner/Driver Information:
Name _____________________________________________________________________
Gran Coupe640i, 640i xDrive, 650i, 650i xDrive
Z4RoadsterZ4 sDrive28i, Z4 sDrive35i, Z4 sDrive35is
4 Series SULEV (PZEV)Coupe428i, 428i xDrive
Convertible428i, 428i xDrive
Introduction [for SULEV (PZEV)
only]
Certain 2014 428i models are certified to
California’s stringent Super Ultra Low Emission
Vehicle (SULEV) standards and also qualify as a
Partial Zero Emission Vehicle (PZEV) under the
California Air Resources Board Zero Emission
Vehicle program. In addition to very low tailpipe
and zero-evaporative emissions, this PZEV
certification includes a unique warranty when the
vehicle is registered in California and certain
other states, as indicated in the SULEV (PZEV)
section beginning on page 35. SULEV (PZEV)
models registered in Delaware, Oregon,
Pennsylvania and Washington are covered by the
California Emission Warranty beginning on
page 26.
The emission certification standard can be
verified on the Vehicle Emission Control
Information label located in the engine
compartment. A representative label is shown
below; the SULEV (PZEV) certification is stated
after the word “California.”
BMW Ultimate Service™
BMW Ultimate Service leads the industry in
providing owners with incredible value and peace
of mind. This service includes:
䉯 The BMW Maintenance Program: No cost
factory-recommended maintenance for
4 years/50,000 miles from the original
in-service date, whichever comes first.
䉯 BMW Roadside Assistance: No-cost 24/7
on-the-road assistance for 4 years/unlimited
miles from the original in-service date. Also
includes trip-interruption benefits as well as
trip routing services.
䉯 New Vehicle Limited Warranty: Limited
coverage for defects in materials and
workmanship for 4 years/50,000 miles from
the original in-service date, whichever comes
first. Repairs will only be made at authorized
BMW centers using Original BMW Parts.
1
The BMW Maintenance Program
The BMW Maintenance Program is a benefit
designed to help reduce the cost of ownership.
This program has been devised with the
following objectives: to maximize vehicle safety,
reliability, and resale value by minimizing
breakdowns resulting from wear, and minimizing
cost and inconvenience by computing
maintenance intervals based upon the specific
manner in which each individual vehicle is driven.
A 2014 2, 4, 6 Series and Z4 vehicle purchased
from an authorized BMW center in the United
States (including Puerto Rico) is covered by the
BMW Maintenance Program for 48 months or
50,000 miles, whichever occurs first. Coverage
begins on the date of first retail sale or the date
the vehicle is first placed into service as a sales
demonstrator, Aftersales Mobility Program (AMP)
Vehicle or BMW Group company vehicle,
whichever is earlier.
Any authorized BMW center in the United States
(including Puerto Rico) will perform the
scheduled and/or additional maintenance
services on your vehicle at no expense to you so
long as your vehicle qualifies for coverage under
the BMW Maintenance Program.
Coverage
The BMW Maintenance Program covers all
factory recommended maintenance, as
determined by the Condition Based Service
(CBS) system. Additional specific items that
need replacement due to normal wear and tear,
and that are not covered by the original New
Vehicle Limited Warranty - such as brake pads,
brake rotors, and wiper blade inserts - are
included, provided wear and tear exceeds BMW
wear limits. Any applicable adjustments required
due to normal operating conditions are also
included. See pages 8-10 of this booklet for
additional information.
Exclusions from coverage include the following:
䉯 Items reimbursable under your New Vehicle
Limited Warranty
䉯 Gasoline and gasoline additive
䉯 Windshield washer additive (except when in
conjunction with scheduled maintenance)
䉯 Tires, wheel alignment, tire balance and
rotation
䉯 Parking brake shoes/linings
䉯 Reset Tire Pressure Monitor
䉯 Wear and tear of soft trim items, such as:
seats, carpets, moldings, headliner, door
panels and all chrome trim
䉯 Damage, including consequential, which
results from negligence, improper operation of
the vehicle, wear and tear or deterioration due
to driving habits or conditions, improper repair,
environmental influences, flood, accident or
fire damage, road salt corrosion, alteration,
installation of non-genuine BMW accessories,
or use of improper, poor quality or
contaminated fuel
䉯 Altered or unreadable Vehicle Identification
Number (VIN) or odometer irregularities or
vehicles where the true mileage cannot be
determined
䉯 Maintenance or repair after the vehicle is
deemed a total loss
䉯 Maintenance or repairs performed by other
than an authorized BMW center within the
United States (including Puerto Rico)
䉯 “Topping off” low fluids (e.g., engine oil,
antifreeze, washer fluid, etc.) except when
done in conjunction with a scheduled
maintenance or other required maintenance
work (as outlined in the customized
maintenance checklist printout) that is
performed during an applicable Maintenance
Program period
䉯 Vehicles used in competitive events
䉯 Oil changes performed outside the
recommended maintenance intervals as
indicated by the Condition Based Service
2
Maintenance Upgrade Option
Please contact your authorized BMW center for
information regarding the purchase of optional
Maintenance Program Upgrades. Eligibility and
coverage exclusions may apply.
Intervals
Time intervals should be followed using the
maintenance intervals as indicated by the BMW
Condition Based Service.
Maintenance intervals on motor vehicles have
conventionally been specified based upon
accumulated mileage. However, driving
conditions have a major influence on routine
maintenance requirements; distance traveled is
only one of the significant factors. A vehicle
driven for 50,000 miles of short trips in the city
with numerous cold starts, prolonged periods of
idling, stop-and-go driving, and high engine
speeds during acceleration requires more
frequent maintenance intervals than a vehicle
driven for 50,000 miles for long distances at low
engine speeds primarily at operating
temperature.
The advanced technologies at BMW have led to
the development of the unique BMW Condition
Based Service (CBS) system which computes
the actual optimum maintenance requirements
based not only upon the accumulated mileage,
but taking into account important factors such as
high or low engine speeds, short or long trip
driving.
Condition Based Service (CBS)
CBS is a further development of the Service
Interval Indicator System.
The remaining times for selected maintenance
tasks as well as any legally prescribed dates are
displayed to you individually:
䉯 Engine oil
䉯 Brakes - front and rear separately
䉯 Brake fluid
䉯 Vehicle check
䉯 Required State Inspection(s)
CBS thus determines the current and future
maintenance requirements. This data can also be
read from the vehicle key by your BMW Service
Advisor and used to propose the optimum scope
of maintenance.
Disconnecting the battery during periods of
long-term storage will interrupt the
calculation of time-based services. BMW
recommends that you have all items requiring
time-based maintenance, such as brake fluid and
possibly also the engine oil and microfilter,
brought up to date by your authorized BMW
center. Also see the section on battery care on
page 11 of this Booklet.
3
Service Required Display
Info Display screen contents
4 Series; 2 Series similar
6 Series only
For certain maintenance operations, you can
view the respective distance remaining or due
date individually in the instrument cluster (Z4
only) or in the Control Display (2 Series, 4 Series
and 6 Series; also Z4 with optional iDrive; see
page 6).
Info Display screens in the instrument
cluster (Z4 only)
1. Push button 1 on the turn indicator lever up
or down repeatedly until the appropriate
symbol appears in the display, accompanied
by the words “SERVICE-INFO”.
2. Press button 2.
3. Use button 1 to scroll through the individual
service items.
Z4 only
The distance remaining until your next service
briefly appears when you switch on the ignition.
The Info Display immediately switches to its
compute mode when you press one of the
two buttons on the turn signal indicator lever.
4
Possible displays (Z4 only)
1. Button for selecting functions
2. Service requirements
3. Engine oil
4. State required safety inspection*/Roadworthiness test
5. Front brake pads
6. Rear brake pads
7. Brake fluid
*Note: The display icons for the state required safety and emissions inspection may be deactivated by
your authorized BMW center, if the state in which your BMW is registered does not require them.
The sequence of displayed service items may vary. The data for the next service appointment is shown
first.
5
Control Display screen contents
(vehicles with iDrive)
The current Status of Service items determined
by the CBS are shown in the Control Display.
You can also view additional information on the
service and maintenance requirements.
1. Open the start menu.
2. Press the controller to open the i-menu.
3. Select “Info sources” and press the
controller.
4. Select “Service Info” and press the controller.
5. If necessary, move the highlight marker. Turn
the controller until “Vehicle status” is
selected and press the controller.
Select the entry and press the controller.
To exit from the menu:
Select the
arrow and press the controller.
Symbols
No service is currently required.
The deadline for service or a state
inspection is approaching. Please contact
your authorized BMW center for an
appointment.
The service deadline has already passed.
6. If necessary, move the highlight marker. Turn
the controller until “Status” is selected and
press the controller.
A list of selected maintenance operations and, if
applicable, inspections required by law is
displayed.
You can request more detailed information on
every entry.
You can request more detailed information on
every entry.
Turn the controller to scroll through the list, then
confirm the selected entry.
Confirm to exit the list.
The current service status is automatically saved in
the vehicle’s key. The Service Advisor at your
authorized BMW center has a device called a key
reader. When your Service Advisor inserts your key
into the key reader, all pertinent vehicle and
servicing data will be available, and a customized
maintenance checklist is printed out based on the
specific operations called for by the Condition
Based Service.
6
Special Note – Maintenance Intervals
The maintenance requirements for your vehicle
are determined dynamically by the Condition
Based Service (CBS) system. The maintenance
items stated herein reflect the latest information
available at the time of the printing of this
Booklet, and are subject to change.
2014 6 Series and Z4 vehicles built prior to July
2013 utilized a different CBS “connected service
item” interval as detailed on page 10.
The completion of certain subsequent
maintenance items or services, as required to
properly maintain your vehicle, will be specified
at intervals computed by the BMW Condition
Based Service system as follows:
䉯 Oil Service: Engine oil should be changed with
the engine at operating temperature.
All 2014 model year 2, 4, 6 Series and Z4
vehicles are factory-filled with BMW High
Performance Synthetic oils. We recommend
BMW High Performance 5W-30 Synthetic Oil
(BMW part number 07 51 0 017 866) for regular
scheduled engine oil changes.
BMW recommends that you check your engine
oil level whenever you add fuel to your vehicle.
For information on checking your engine oil level,
refer to your vehicle’s Owner’s Manual.
If you need to add oil between oil changes and
BMW High Performance Synthetic Oil is
unavailable, for the purpose of topping up the
engine oil level only, BMW recommends use of
one of the below-listed synthetic oils:
䉯 Castrol Syntec European Formula SAE 0W-30
䉯 Castrol Edge with SPT SAE 5W-40
䉯 Mobil 1 SAE 0W-40
䉯 Pennzoil Platinum European Formula Ultra
SAE 5W-30
䉯 Valvoline SynPower SAE 5W-30
The choice of the right SAE grade is based on
the climatic conditions in the region in which you
normally drive your BMW. To best determine
which SAE grade is best suited for your vehicle,
contact an authorized BMW center.
If you are unable to obtain a recommended
synthetic oil from the list above, for the purpose
of topping up the engine oil level only, use only a
synthetic oil with an API rating of SM or higher.
The following maintenance services:
– Brake Fluid Service;
must be performed when required as indicated
by the following as applicable:
䉯 The specified CBS engine oil service counter
interval
䉯 The time interval (the first occurrence based
on the vehicle’s production date)
䉯 The stated mileage for a “non-connected”
maintenance service
Refer to pages8-10foradditional information.
Additionally,
– The engine coolant has a long-term rating and
does not need to be changed except for system
repairs.
– The automatic and manual transmissions, and
the all-wheel drive transfer cases installed in
BMW vehicles are factory filled with long-term
rated fluids. The transmission long-term rated
fluid does not need to be changed except when
necessary during repairs to the transmission.
The transfer case long-term rated fluid does
not need to be changed except when indicated
by the vehicle or when necessary during repairs
to the transfer case.
7
For your convenience, you may also wish to have
your authorized BMW center perform any
necessary operations to fulfill any state
inspection requirements in your area, concurrent
with the maintenance services specified above
during other repairs. Should you request more
frequent maintenance service, the cost of
these services will not be covered by the
Maintenance Program.
BMW has applied the most modern
technological advances not only to the design
and production of your vehicle, but also to
computing of the optimum maintenance interval
for your type of operations and driving style. Your
authorized BMW center has made a substantial
investment in unique BMW special service tools
to enable BMW factory trained service
technicians to perform quality repairs on your
BMW in minimal time, to help maximize your
satisfaction with your BMW, its longevity, and
resale value.
Quality Certification I
For a detailed list of items inspected, refer to the
Quality Certification I form provided to the Owner
at time of delivery. A copy of the form is on file at
the selling authorized BMW center.
and, when applicable, adjusting the engine idle.
We suggest having this work performed by your
authorized BMW center, perhaps while regular
maintenance is performed. Your authorized BMW
center can also recommend a gasoline additive
that will provide sufficient detergency.This
recommended unscheduled maintenance which
may be necessitated by use of inappropriate
fuels is not required in order to maintain the
emission warranty. It also is not covered by your
vehicle’s warranty because no defect in material
or workmanship or component failure is involved.
Maintenance Service Summary
The Condition Based Service (CBS) system will
determine the requirement for performing the
maintenance services described in this section,
ending on page 10. These services may be
required either individually or in conjunction with
other maintenance services.
Maintenance services are performed as outlined
in this section, based on intervals of either time,
mileage or after performing a specified number
of previous services. These intervals correspond
to the latest information available when this
Booklet was printed. Maintenance intervals are
subject to change with newer vehicles or may
also apply retroactively. Your authorized BMW
center will be able to advise and perform
maintenance services as required by the most
recent information that applies to your vehicle.
The maintenance services “connected to a
specific CBS engine oil service,” as outlined
below, apply to vehicles built as of July 2013.
6 Series and Z4 vehicles built prior to July 2013
utilized a different CBS “connected service item”
interval as detailed on page 10.
Fuel Quality – Gasoline (gasoline
engines only)
Only use fuels advertised to have adequate
detergency and low alcohol (such as ethanol)
content. Please refer to your owner’s manual for
important information on the fuel recommended
for use in your vehicle. Use of fuels with
insufficient detergent and/or excess alcohol can
cause driveability problems that necessitate
cleaning intake valves and fuel injection valves,
Standard operations
Maintenance work:
䉯 Verify Check Control messages.
䉯 Check indicator and warning lights.
䉯 Reset CBS display.
䉯 Inspect tires, adjust tire pressures and reset
Tire Pressure Monitor.
䉯 Check parking brake functionality while the
vehicle is being driven into the workshop.
8
Engine oil
Vehicle check
Maintenance work:
䉯 Change the engine oil and oil filter (as shown
in CBS). We recommend BMW High
Performance 5W-30 Synthetic Oil
P/N 07 51 0 017 866.
Maintenance services connected to a
specific engine oil service*
*These additional connected services will not be
shown in the vehicle’s CBS display.
Maintenance work:
䉯 After every 2nd Engine Oil Service: Ventilation
microfilter: replace ventilation microfilter.
䉯 After every 5th Engine Oil Service: Intake air
cleaner: replace air filter element (reduce
replacement interval in dusty operating
conditions).
Maintenance services that display in
CBS
Front brakes
Maintenance work:
䉯 Replace brake pads, clean brake pad contact
points in calipers.
䉯 Brake discs: Check surface and thickness,
replace as necessary.
Rear brakes
Maintenance work:
䉯 Replace brake pads, clean brake pad contact
points in calipers.
䉯 Brake discs: Check surface and thickness,
replace as necessary.
䉯 Parking brake: Repair or replace parking brake
shoes/linings only if a reduction in the brake’s
effectiveness is noted. When fitted, parking
brake shoes/linings are excluded from
coverage under the BMW Maintenance
Program.
Maintenance work:
䉯 Check operation of horn, headlight flasher and
Spark plugs (connected to specific
Engine Oil Service)
Maintenance work:
䉯 Replace spark plugs at the following intervals:
– All models except Z4 sDrive35i and
Z4 sDrive35is (see below): At every 6th Engine
Oil Service (approximately 60,000 miles).
– Z4 sDrive35i, Z4 sDrive35is: At every 4th
Engine Oil Service (approximately
40,000 miles).
Emission Control Maintenance
Schedule
The maintenance schedule as shown is required
for the proper functioning of the emission control
systems for optimum vehicle performance and
fuel economy.
Basic Engine
Engine oilAs specified by CBS
Engine oil filterAs specified by CBS
Connected maintenance services items
intervals for 2014 vehicles built as of July 2013:
Fuel System
Air filterReplace at every 5th
Air filter (Z4 only)As specified by CBS
Ignition System
Spark plugs
(All models except
Z4 sDrive35i and
Z4 sDrive35is; see
below)
Spark plugs
(Z4 sDrive35i,
Z4 sDrive35is)
Engine Oil Service
At every 6th Engine Oil
Service (approximately
60,000 miles)
At every 4th Engine Oil
Service (approximately
40,000 miles)
Emission Control
Components
Oxygen sensor120,000 miles
Oxygen sensor
(228i, M235i, 428i,
428i xDrive, 435i,
435i xDrive, 640i,
640i xDrive and
Z4 sDrive28i if eligible
for the California
Emissions Warranty)
Oxygen sensor
(SULEV (PZEV) only)
150,000 miles
150,000 miles
Oxygen Sensor Service: The oxygen sensor
deteriorates strictly on a mileage basis and must
therefore be replaced to maximize vehicle fuel
economy and minimize exhaust pollution.
Connected maintenance services items
intervals for 2014 6 Series and Z4 vehicles
built prior to July 2013:
Fuel System
Air filterReplace at every 3rd
Ventilation microfilterAt every brake fluid
Ignition System
Spark plugs
(6 Series and
Z4 sDrive28i)
Spark plugs
(Z4 sDrive35i,
Z4 sDrive35is)
Vehicle
Vehicle checkAt every 2nd Engine Oil
Engine Oil Service
service
At every 4th Engine Oil
Service
At every 3rd Engine Oil
Service
Service
10
12 Volt Battery Care
If your car is driven only for short distances of
less than 10 miles over a prolonged period of
time, without an occasional drive at highway
speeds, the engine’s charging system will not
maintain the battery. Insufficient use of the
vehicle could result in short term starting
problems and, in the long term, could damage
the battery.
In case the car is not operated for several weeks,
it is advisable to:
䉯 consider using a proper trickle charger,
following the charger manufacturer’s
instructions, to maintain the battery’s state of
charge; or
䉯 consult your authorized BMW center regarding
battery removal. Once removed, the battery
must be charged and stored in a cool, dry
place where it can be protected from freezing.
If the battery will be stored for over 3 months, it
must be recharged every 3 months, or else it
will become damaged and useless.
Please consult with your authorized BMW center
for further guidance and information.
During manufacture, metal exterior body parts
receive an additional corrosion protection coat.
Hood, trunk, doors and other body parts are
coated with PVC and sealed from the outside.
All floor panels receive a resilient coating of PVC
for maximum protection against damage due to
stones, etc.
Corrosion protection materials tested over many
years are applied to the surfaces of cavities and
to the entire underside of the vehicle during and
after assembly.
For additional information on the 12-year
unlimited mileage anti-corrosion warranty see
the Warranty Section of this Booklet (page 22).
Restoring corrosion protection
Please take care that anti-corrosion material is
replaced when your car is repaired after body or
chassis damage.
BMW will not accept any liability for repair of,
or damage caused by, any parts and
accessories not approved by BMW.
Underbody maintenance
Corrosion Protection
Extensive corrosion protection measures
implemented by BMW now make it possible to
offer a 12-year unlimited mileage anti-corrosion
warranty against rust perforation on your vehicle
provided that the vehicle is properly maintained.
Information on proper maintenance is available in
this Booklet and your vehicle’s Owner’s Manual.
The major degree of corrosion protection is due
to the electrophoretic dip painting process which
cathodically deposits paint particles on all body
parts, attracting paint particles into the minutest
cavities or seams. Body parts are designed to
provide optimum corrosion protection.
The underbody has to be cleaned at least once a
year, in Spring, with plain water in order to
remove mud, chemical sediments and other
deposits. If those materials are not removed,
corrosion (rust) will occur on metal components.
Your authorized BMW center can do this
anti-corrosion service for you.
Do not apply additional undercoating or
rust-proofing on or near the exhaust
manifold, exhaust pipes, catalytic converter or heat
shields. During driving, the substance used for
undercoating could overheat and cause a fire.
11
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.