Blue-White A-1614-3N, A-1614-4, A-1600T, A-1614-6, A-1614-7 Series Manual

R

Page 2

Thank You

Blue White Industries

[phone].

LEAVE THIS INSTRUCTION MANUAL WITH INSTALLED METER!

******** SPECIFICATIONS ********

MODEL NO: MAXIMUM MAXIMUM FEED RATE
P.S.I ML/MIN OZ/MIN G.P.H G.P.D

NOTE: Norprene tubing same feed rate as Tygon

1.18

1.75

1.43

3.18

5.12

5.75

6.75

1.87

L

R

Thank You for purchasing the A-1600 Peristaltic Metering Pump. It is our policy
to produce, market and provide service on our products to ensure your safety
and
complete satisfaction. When installed and used in accordance with the following
instructions, the A-1600 will provide years of safe, reliable service.

For your safety the A-1600 was designed to be safe and easy to use. However,
there are limits to its operation. This instruction manual contains safety precau­tions, which if ignored could result in personal injury and/or property damage.

Read these instructions carefully before installing the pump. If you are not
satisfied that the unit can be safely operated, call the place of purchase for

25
25
25
25
25
25
25
25
25

25

25
25

3
17
60
75

11

40

130
195

14

54

195
295

.1
.5

2.0

2.5
.3

1.3

4.4

6.5
.4

1.8

6.5

9.9

.04
.26
.95

1.18
.17
.63

2.05

3.08
.22

.85

3.08

4.67

1

6
22
28

4
15
49
74

5
20
74

112

A-1614-3N
A-1614-4
A-1614-6
A-1614-7
A-1630-3N
A-1630-4
A-1630-6
A-1630-7
A-1645-3N

A-1645-4

A-1645-6
A-1645-7

Page 3

INSTALLATION INSTRUCTIONS

UNPACKING INFORMATION

Verify that you have received all of the following equipment:

- One A-1600 series pump

- 10 ft. 3/8” O.D. Clear vinyl tubing with flow indicator

- One threadless injector (T.I.) Fitting

- One suction tube strainer

- One ceramic weight

- Two pump head tube assemblies (with fittings)

- Two mounting screws

LOCATION AND MOUNTING
CAUTION

ALWAYS WEAR EYE PROTECTION AND PROTECTIVE CLOTHING WHEN
WORKING AROUND CORROSIVE MATERIAL.

A. Choosing a well ventilated area located near the supply tank, Electrical
supply and injection points.
B. The injector may be shelf or wall mounted. Use the inclosed hardware for
wall mounting.
C. When using wall corrosive chemicals, avoid mounting the injector directly
above the supply tank. Although the pump housing is designed to withstand
corrosion, some chemical fumes may damage the unit.
D. Your solution tank should be sturdy plastic and chemically resistant to the
chemicals you are using to protect from fume, a tight fitting cover should be in
place at all times. A variety of tanks are available from the factory.

ELECTRICAL CONNECTIONS

WARNING - RISK OF ELECTRIC SHOCK

Be certain you connect the unit to the proper supply voltage. Using the incorrect
voltage will damage the injector and may result in injury. The units voltage
requirements is printed on the name plate

A-1600 MODELS
A-1600 Model Injector are supplied with a junction box and cover. To reduce
the risk of electric shock when field wiring, be certain that the grounding
conductor is attached to the green ground screw, located inside the junction box.

A-1600T MODELS

(Timer Equipped Model)
115V Model Injector are supplied with a ground wire conductor and a grounding
type attachment plug. To reduce the risk of electric shock, be certain that it is
connected only to the properly grounded, grounding type receptacle. A ground
fault interrupter (GFI) receptacle is recommended for use in wet locations.

24V/230V Models Injectors are supplied with a ground wire conductor. To
reduce the risk of electric shock, be certain that the green grounding conductor
is connected only to a properly grounded field wiring box.

LL

R

Page 4

FILTER

CIRCULATION
PUMP

INJECTOR

SOLUTION
TANK

RETURN
LINE

SWIMMING POOLS
Figure 1

Submersible well pump

Contact
tank

To system

Well cover

Pressure
switch

Solution
tank

Pressure
guage

WELL

WATER WELLS
Figure 2

L

R

Pressure
relief
valve

Drain

Suction Tube
Injector Point

Page 5

WIRING DIAGRAM
Figure 3

WIRING DIAGRAM
A-1600T SERIES

(Timer Models Only)

Motor

Injecting
Indicator
Light

Cycle Timer

Power
Indicator
Light

Power
Switch

Ground

Hot

Common

A- 1600 SERIES

WIRING COLOR CODES
Figure 4

**************MOTOR************

VOLTAGE HOT COMMON GROUND

115v Black or Yellow Blue Green

230v Black or Yellow Red Green

24v Blue White Green

******** CIRCUIT BOARD*******

(TIMER MODELS ONLY)

HOT

(Load and Input)

COMMON

(Input)

LOAD

(Load)

Black White Red

Red

Black

White