®
MODEL A-100N
Peristaltic Injector Pump
Operating Manual
Models A-100NA, A-100NC, A-100NS, A-100NF, A-100NX
5300 Business Drive
Huntington Beach, CA 92649
USA
Phone: 714-893-8529 FAX: 714-894-9492
E mail: sales@blue-white.com or techsupport@blue-white.com
Website: www.blue-white.com
Blue-White
Industries, Ltd.
R
A-100NPage 2
TABLE OF CONTENTS
1.....Introduction....................................................................................3
2.....Specifications .......................... ............................ ............................3
3.....Features .................... ........................................................ ..............3
4.....Unpacking .. ............................ .......................................... ..............4
5.....Installation................ ............................ ............................ ..............4
5.1..Mounting location ............. .......................................... ..............4
5.2..Optional circuit board signal connection installation... ..............6
5.3..Input power connections ............................................. ..............8
5.4..How to install the tubing and fittings............. ............................10
6.....How to adjust the output ..................... ..........................................11
6.1..Fixed cycle timer models .............................. ............................11
6.2..Variable speed model ........ ........................................................11
6.3..TFD - Tube Failures Detection system ........................ ..............12
6.4..FVS - Flow verification System .................................. ..............12
7.....How to maintain the Pump.... ............................ ............................14
7.1..Routine inspection and cleaning...... ............................ ..............14
7.2..How to clean and lubricate the Pump ........................................14
7.3..How to replace the pump tube ..................................... ..............15
Replacement parts drawing... .......................................... ..............16
Replacement parts list............ ............................ ............................17
Warranty information............ .......................................... ..............18
Authorized service centers..... .......................................... ..............19
A-100N Page 3
1.0 Introduction
Congratulations on purchasing the A-100N Peristaltic Metering Pump. The
A-100N is designed to inject chemicals into piping systems. The pump has
been tested by NSF International for use with 12 ½% Sodium Hypochlorite.
This manual covers the following feed rate adjustment mechanisms:
1. Fixed Cycle Timer - (Models A-100NA, A-100NC, A-100NS) The
fixed speed pumping mechanism is turned on and off by an electronic timer.
The total cycle time is factory set. The on-time cycle is adjustable from 5%
through 100% of the total cycle time. Model A-100NA has a 1 minute cycle
with a 60 second adjustable on-time. Model A-100NC has a 5 second cycle
with a 5 second adjustable on-time. Model A-100NS (ideal for spa and hot
tub chlorination) has a 1 minute cycle with a 6 second adjustable on-time.
(Custom cycles are available from the factory).
2. Variable Speed Controller - (Model A-100NF) The speed of the
pumping mechanism is adjustable from 5% through 100%.
3. Fixed Feed Rate - (Model A-100NX) No adjustment control.
2.0 Specifications
Maximum Working Pressure 100 psig / 6.9 bar (most models)
o o
Maximum Fluid Temperature 130 F / 54 C
o o
Ambient Temperature Range 14 to 110 F / -10 to 43 C
Duty Cycle Continuous
Maximum Solids 50% by volume
Maximum Viscosity 5,000 Centipoise
Maximum Suction Lift up to 30 ft. water
Power Requirements 108/130Vac 60Hz 80 Watts,
208/250Vac 50Hz 40 Watts,
208/250Vac 60Hz 45 Watts
Dimensions 6-1/8” H x 10-1/8” W x 9” D
Weight 8 lb.
3.0 Features
!
Peristaltic Pump Tube does not require valves.
!
Self priming under maximum pressure. Cannot vapor lock.
!
High outlet pressure capability of 100 psig (most models).
!
High inlet suction lift capability of 30 feet.
!
Patented Tube Failure Detection (TFD) system.
!
Patented pump tube assembly design.
!
Includes Flow Verification System (FVS) - sensor sold separately.
!
Open collector (sinking 50mA max) alarm output. (30V DC max)
!
Corrosion proof Valox housing.
!
Tamper resistant electronic control panel cover.
5.0 Installation
Note: All diagrams are strictly for guideline purposes only. Always consult
an expert before installing the pump into specialized systems. The pump
should be serviced by qualified persons only.
5.1 Mounting Location
Choose an area located near the chemical supply tank, chemical injection
point and electrical supply. Although the pump is designed to withstand
outdoor conditions, a cool, dry, well ventilated location is recommended.
Install the pump where it can be easily serviced.
!
Mount the pump to a secure surface or wall using the enclosed hardware.
Wall mount to a solid surface only. Mounting to drywall with anchors is not
recommended.
!
Mount the pump close to the injection point. Keep the outlet (discharge)
tubing as short as possible. Longer tubing increases the back pressure at the
pump tube.
!
Your solution tank should be sturdy. Keep the tank covered to reduce
fumes. Do not mount the pump directly over your tank. Chemical fumes
may damage the unit. Mount the pump off to the side or at a lower level
than the chemical container.
!
Mounting the pump lower than the chemical container will gravity feed the
chemical into the pump. This “flooded suction” installation will reduce
output error due to increased suction lift. You must install a shut-off valve,
pinch clamp or other means to halt the gravity feed to the pump during
servicing.
!
Be sure your installation does not constitute a cross connection with the
Page 4
CAUTION: Proper eye and skin protection must be
worn when installing and servicing the pump.
CAUTION: Proper eye and skin protection must be
worn when installing and servicing the pump.
4.0 Unpacking
Your pump package should contain the following:
1 - Injector pump with 2 pump tube assemblies
1 - suction tube strainer
1 - ceramic tubing weight
1 - 5’ Length of clear PVC suction tubing
1 - 5’ Length of opaque LLDPE discharge tubing
1 - Injection fitting with internal back-flow check valve
1 - Mounting hardware kit
A-100N
Page 5
Floor Mount
Wall Mount
7-3/8”
7-5/8”
3-1/2”
8-3/16”
Drill .156 Dia. (5/32)
For Self-Tap Screw
#10 X 1” Phillips Steel
4 Places
Drill .156 Dia. (5/32)
For Self-Tap Screw
#10 X 1” Phillips Steel
2 Places
INJECTOR MOUNTING
Note: For wall-mounting, drill & thread into
solid wood only.
TYPICAL INSTALLATION
R
Suction
Tube
Chemical
Container
with cover
Discharge
Tube
Strainer
Ceramic Weight
Injection / Check valve
with 1/4” and 1/2” male
pipe threads.
Mount in upward position
to prevent trapped gasses
in the injection fitting.
Wall or shelf mount
away from the top of the
solution tank. Chemical
fumes can damage the
unit.
PARTS LOCATOR DRAWING
* Slide both top & bottom clamps to the left only far enough to open the control cover.
9
8
3
Control
Control Cover
Pumphead
Enclosure
Rear Plate
Pumphead
Cover
6.0
Pumptube
Assembly
Rotor
Assembly
9
8
1
Slide Clamps*
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
BLUE-WHITEINDUSTRIES
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
A-100N
Page 6 A-100N
1/2” DIAMETER KNOCKOUT
LIQUID-TIGHT CONNECTOR
5.2 Optional circuit board signal connection installation - The
pump includes three optional external signal connections:
!
!
!
FVS - FLOW VERIFICATION SENSOR INPUT
Accepts a pulse signal from an optional Blue-White sensor confirming that
fluid is passing through the pump. Triggers and alarm output if fluid is not
detected.
AL - ALARM OPEN COLLECTOR OUTPUT
The output (purple wire) sinks to DC ground when an alarm condition
exists. 6-30Vdc collector voltage. 50mAdc maximum sinking current.
MA - MOTOR ACTIVE OPEN COLLECTOR OUTPUT
The output (brown wire) sinks to DC ground when the motor is deenergized. 6-30Vdc collector voltage. 50mAdc maximum sinking current.
All signal wires must be connected to the circuit board, located inside the
pump enclosure, using connector plug wiring assemblies. A liquid-tight
connector must be installed in the pump enclosure wall and the signal wires
passed through the liquid-tight connector and secured. See pages 8 & 9 for
wiring details.
1. Remove the rear enclosure panel.
2. Remove knock-out using a screwdriver.
3. Trim edge with a knife and remove sharp edges.
4. Install the provided liquid-tight connector.
5. Connect the connector plug to the circuit board.
Page 7A-100N
T1
T2
230VAC
T3
T4
HOT
LOAD
120 VAC
MA AL
TFD
-
+-+
-
++
FVS
-
SIG
FVS - FLOW VERIFICATION
SENSOR INPUT
AL - OPEN COLLECTOR
ALARM OUTPUT
MA - OPEN COLLECTOR
MOTOR ACTIVE OUTPUT
CIRCUIT BOARD SIGNAL CONNECTION
Page 8
5.3 Input Power Connections
Be certain to connect the pump to the proper supply voltage. Using the
incorrect voltage will damage the pump and may result in injury. The
voltage requirement is printed on the pump serial label.
The pump is supplied with either a ground wire conductor and a grounding
type attachment plug (power cord) or a junction box for field wiring.
POWER CORD MODELS -To reduce the risk of electric shock, be certain
that the power cord is connected only to a properly grounded, grounding
type receptacle.
JUNCTION BOX MODELS -To reduce the risk of electric shock, be
certain that a grounding conductor is connected to the green grounding
conductor located in the junction box.
Note: When in doubt regarding your electrical installation, contact a
licensed electrician.
WARNING: Risk of electric shock.
WARNING: Risk of electric shock.
INPUT
VOLTAGE
115VAC 60Hz
220VAC 50Hz
HOT
LEADWIRE
NEUTRAL
LEADWIRE
GROUND
LEADWIRE
230VAC 60Hz
YELLOW
YELLOW
YELLOW
BLUE
BROWN
RED
GREEN
GREEN
GREEN
MOTOR LEADWIRES
CIRCUIT BOARD SIGNAL IN/OUT CONNECTIONS
WIRE COLOR CODE
SYSTEM DESCRIPTION
FVS - FLOW VERIFICATION SENSOR INPUT
Accepts a pulse signal from an optional Blue-White sensor
confirming that fluid is passing through the pump.
Triggers and alarm output if fluid is not detected.
AL - ALARM OPEN COLLECTOR OUTPUT
The output (purple wire) sinks to DC ground when an alarm
condition exists.
6-30Vdc collector voltage. 50mAdc maximum sinking current.
BROWN (+) & BLACK (-)
RED (+ 20VDC)
BLACK (-)
YELLOW (signal)
TFD - TUBE FAILURE DETECTION SYSTEM INPUT
Monitors a pair of sensors in the pumphead. Triggers an alarm
output if fluid with a conductivity of greater than 500 micro-seimens
is detected. Typical chemicals include chlorine, acid, caustic.
The system will not detect water or silicone lubricating oil.
MA - MOTOR ACTIVE OPEN COLLECTOR OUTPUT
The output (brown wire) sinks to DC ground when the motor is
de-energized.
6-30Vdc collector voltage. 50mAdc maximum sinking current.
PURPLE (+) & BLACK (-)
GRAY & GRAY
90VDC
(+) RED
(-) BLACK
GREEN
A-100N
Page 9
WIRING DIAGRAM - Model A-100NA & A-100NC
PRIME
SWITCH
WIRING DIAGRAM - Model A-100NS
T1
T2
230VAC
T3
T4
HOT
LOAD
(+)
(-)
COMMON
OPTIONAL POWER
INDICATOR LAMP
HOT
HOT
POWER
SWITCH
108/130 VAC
PURPLE
BLACK
CYCLE ADJUSTMENT
POTENTIOMETER
OPTIONAL INJECTOR
INDICATOR LAMP
120 VAC
208/240 VAC
NEUTRAL
AC
INPUT
AC
MOTOR
GROUND
MA AL
TFD
-+-
+
-
++
FVS
-
SIG
T1
T2
230VAC
T3
T4
HOT
LOAD
(+)
(-)
COMMON
OPTIONAL POWER
INDICATOR LAMP
HOT
HOT
108/130 VAC
PURPLE
BLACK
CYCLE ADJUSTMENT
POTENTIOMETER
OPTIONAL INJECTOR
INDICATOR LAMP
120 VAC
208/240 VAC
NEUTRAL
AC
INPUT
AC
MOTOR
GROUND
MA AL
TFD
-+-
+
-
++
FVS
-
SIG
WIRING DIAGRAM - Model A-100NF
(+)
(-)
COMMON
OPTIONAL POWER
INDICATOR LAMP
HOT
POWER
SWITCH
PURPLE
BLACK
SPEED ADJUSTMENT
POTENTIOMETER
AC
INPUT
DC
MOTOR
GROUND
MA AL
TFD
-+-
+
-
++
FVS
-
SIG
NOTCH LOCATION INDICATES
INPUT POWER REQUIREMENT
108/130 VAC
208/240 VAC
WHITE
YELLOW
BLACK
RED
(+) 90 Vdc
(-) Vdc
A-100N
Page 10
5.4 How To Install the Tubing and Fittings
! Inlet Tubing - Locate the inlet fitting of the Pump Tube. Remove the tube
nut. Push the clear PVC suction tubing onto the compression barb of the
fitting. Use the tube nut to secure the tube. Hand tighten only.
CAUTION: Proper eye and skin protection must be
worn when installing and servicing the pump.
CAUTION: Proper eye and skin protection must be
worn when installing and servicing the pump.
Foot
Strainer
Ceramic
Weight
Tubing
Suction 3/8"
! Strainer - Trim the inlet end of the suction tubing so that
the strainer will rest approximately two inches from the
bottom of the solution tank. This will prevent sediment
from clogging the strainer. Slip the ceramic weight over the
end of the suction tube. Press the strainer into the end of
the tube. Secure the ceramic weight to the strainer. Drop
the strainer into the solution tank.
! Outlet Tubing - Locate the outlet fitting of the Pump
Tube. Remove the tube nut. Push the opaque outlet
(discharge) tubing onto the compression barb of the fitting.
Use the tube nut to secure the tube. Hand tighten only.
Keep outlet tube as short as possible.
! Injection/Check Valve Fitting Installation - The
Injection/Check valve fitting is designed to install directly
into either 1/4” or 1/2” female pipe threads. This fitting will
require periodic cleaning, especially when injecting fluids
that calcify such as sodium hypochlorite. See section 7.0.
Install the Injection/Check valve directly into the piping
system. To prevent trapped gasses, install the fitting in an
upward direction. Use Teflon thread sealing tape on the pipe
threads.
Push the opaque outlet (discharge) tubing onto the compression barb of the Injection/Check valve fitting. Use the tube
nut to secure the tube. Hand tighten only.
Inlet Adapter
Outlet Adapter
Pump Head
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
BLUE-WHITEINDUSTRIES
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
A-100N
Page 11
6.0 How to Adjust The Output
6.1 Fixed Cycle Timer Models -The pumping
mechanism is turned on and off by an electronic
cycle timer. The total-time cycle is factory preset
and is not user adjustable. The on-time cycle is
adjustable from 5% to 100% of the total cycle time
(model A-100NS timers adjust from .5 to 6
seconds with total time cycle of 60 seconds).
Example: If the total-time cycle is 60 seconds and
the on-time cycle is adjusted for 25 percent, the
pump will run for 15 seconds and turn off for 45
seconds (60 second total cycle). This cycle is
repeated until either the power switch is turned off, the cycle time is
changed or the input power is disconnected from the pump.
To adjust the pump output -
!
Slide the slide clamps to the left only far enough to open the control panel
door.
!
Turn the adjustment knob to the desired percentage of on-time per cycle.
Note: When power is applied to the pump, the A-100N will either
automatically begin to pump, or maintain power-off status, depending
on the power switch status.
6.2 Variable Speed Model -The speed of the pumping mechanism is
adjustable from 5 % through 100%.
To adjust the pump output -
!
Slide the slide clamps to the left only far enough to open the control panel
door.
!
Turn the adjustment knob to the desired percentage of speed.
SLIDE CLAMP
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
BLUE-WHITE INDUSTRIES
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
BLUE-WHITE INDUSTRIES
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
A-100N
6.3 TFD (Tube Failure Detection) - The pump is equipped with a Tube
Failure Detection System which is designed to stop the pump and provide
an open collector (sinking) output signal in the event the pump tube should
rupture and chemical enters the pump head. This patented system is capable
of detecting the presence of a large number of chemicals including Sodium
Hypochlorite (Chlorine), Hydrochloric (muriatic) Acid, Sodium Hydroxide,
and many others. The system will not be triggered by water (rain, condensation, etc.) or silicone oil (roller and tubing lubricant).
Page 12
Chemical
Tubing failure
If the system has detected chemical, the
pump tube must be replaced and the
pump head and roller assembly must
be thoroughly cleaned.
Confirm Chemical Detection - To
determine if your chemical will be
detected by the system, remove the pump
tube and roller assembly. Place a small
amount of the chemical in the bottom of
the pump head - just enough to cover the sensors. Turn on the pump. If the
TFD system detects the chemical, the pump will stop after a five second
confirmation period. If the TFD system does not detect the chemical, the
pump will continue to run after the confirmation period. Carefully clean the
chemical out of the pump head being sure to remove all traces of chemical
from the sensor probes. Turn the power switch off and on to reset the pump.
Open Collector Alarm Output - An open collector (sinking) output signal
is provided with the TFD system. (See page 6).
Confirm the FVS flow range - The Flow Verification Sensor (FVS) will
only function within its operating range. Sensor model FV-100-6V has an
operating range of 30-300 ml/min (1-10 oz/min). If the pump’s output is
less than 30 ml/min (0.5 ml/sec), the sensor will not detect chemical and a
signal will not be sent to the pump.
6.4
(FVS) Flow Verification System The pump is equipped with a
Flow Verification System which is designed to stop the pump and provide
an open collector (sinking) output signal in the event the sensor does not
detect chemical during pump operation. This could indicate a clogged
injection fitting, empty chemical solution tank, worn pump tube, loose
tubing connection, etc.
The system features an alarm delay time of 6 seconds which allows the
pump to clear any gasses that may have accumulated during stopped
operation. The pump will stop, and the alarm mode activated, if no pulses
are received by the pump and the alarm delay time period has ended. Turn
the power switch off and on to clear the alarm and restart the pump. The
Flow Verification Sensor is sold as an optional accessory.
-
A-100N
Page 13
OPERATING
FLOW RANGE
(ml/min)
OPERATING
FLOW RANGE
(ml/min)
30-300
FV-100-6V
100-1000
FV-200-6V
200-2000
FV-300-6V
300-3000
FV-400-6V
500-5000
FV-500-6V
700-7000
FV-600-6V
SENSOR
MODEL
NUMBER
Install the FVS Flow Sensor - The Flow Verification Sensor (FVS) should
be installed on the inlet (suction) side of the pump tube. The sensor includes
a PVC tubing insert, located inside the sensor’s female thread connection,
that is designed to seal the sensor onto the pump tube inlet adapter. Thread
the sensor onto the pump tube until the tubing insert is snug against the
pump tube inlet fitting - do not over-tighten.
Connect the red/white (+), black (-), and bare (signal) wires from the sensor
to the red (+), black (-), and yellow (signal) wires on the plug connector.
Knock-out the liquid-tite connector mounting hole on the side of the pump
enclosure and install the liquid tight connector. Route the wires through the
connector and tighten the connector nut. Plug the connector onto the circuit
board at the pins marked “FVS”. See page 6.
Open Collector Alarm Output - An open collector (sinking) output signal
is provided with the FVS system. (See page 6).
Inlet Adapter
Outlet Adapter
FVS Sensor
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
BLUE-WHITE INDUSTRIES
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
A-100N
Page 14
7.0 How to Maintain the Pump
7.1 Routine Inspection and Maintenance
The pump requires very little maintenance. However, the pump and all
accessories should be checked weekly. This is especially important when
pumping chemicals. Inspect all components for signs of leaking, swelling,
cracking, discoloration or corrosion. Replace worn or damaged components immediately.
Cracking, crazing, discoloration and the like during the first week of
operation are signs of severe chemical attack. If this occurs, immediately
remove the chemical from the pump. Determine which parts are being
attacked and replace them with parts that have been manufactured using
more suitable materials. The manufacturer does not assume responsibility
for damage to the pump that has been caused by chemical attack.
7.2 How to Clean and Lubricate the Pump
The pump will require occasional cleaning and lubricating. The amount
will depend on the severity of service.
]
When changing the pump tube assembly, the pump head chamber, roller
assembly and pump head cover should be wiped free of any dirt and debris.
]
The pump head cover bearing may require grease periodically. Apply a
small amount of grease (Aeroshell aviation grease #5 or equivalent) when
necessary.
]
Although not necessary, 100% silicon lubrication may be used on the
roller assembly and tube assembly.
]
Periodically clean the injection/check valve assembly, especially when
injecting fluids that calcify such as sodium hypochlorite. These lime
deposits and other build ups can clog the fitting, increase the back pressure
and interfere with the check valve operation.
]
Periodically clean the suction strainer.
]
Periodically inspect the air vents located under the motor compartment
and on the rear panel. Clean if necessary.
CAUTION: Proper eye and skin protection must be
worn when installing and servicing the pump.
CAUTION: Proper eye and skin protection must be
worn when installing and servicing the pump.
A-100N
Page 15
Remove the Old Pump Tube - The pump roller assembly spins in a
counter clockwise direction. The pump head inlet (suction) side is located
at the bottom of the pump and the outlet (discharge) is located at the top of
the pump head.
+ Release any pressure that may be in
the discharge tubing.
+ Disconnect the suction and discharge
tubes from the pump tube.
+ Remove the pump head cover.
+ With the pump running, pull the inlet
fitting out of the pumphead. Guide the
tube counter clockwise away from the
rollers. Pull the outlet fitting out of the
pump head.
Install the New Pump Tube - Be sure the pump head chamber is clean and
free of any debris.
Remove and inspect the roller assembly. Be sure the rollers spin freely. If
required, apply a small amount of grease to the pump head cover bearing.
+ With the pump running, insert the inlet (suction) side of the Pump Tube
fitting into the pump head.
+ Carefully guide the Pump Tube into the pump head. Stretch the tube
slightly and insert the outlet (discharge) fitting into the upper retaining slot
in the pump head.
+ Place the clear cover on the pump head and secure with three screws.
7.3 How to Replace the Pump Tube
The pump tube assembly will eventually break if not replaced. The tube has
been designed for a minimum service life of 500 hours. However, the life
of the tube is affected by many factors such as the type of chemical being
pumped, the amount of back pressure, the motor RPM, temperature and
others. The pump tube assembly must be inspected and replaced regularly.
Inlet Adapter
Outlet Adapter
Pump Head
A-100N
0%
100%
50%
75%
I
O
25%
ON OFF
BLUE-WHITEINDUSTRIES
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
A-100N
28
29
Page 16
49
REPLACEMENT PARTS DRAWING
OPTIONAL
JUNCTION BOX
37
38
39
45
48
46
40
11
3
13
30
17
26
27
3
2
1
5
4
7
8
12
25
24
23
22
20
21
18
36
31
14
51
50
A1
0
-
0
N
0%
1
0
%
0
0
5
%
5
7
%
I
O
%
25
O
N
F
O
F
IR
W
E
B
D
T
U
N
I
HE
L
-
U
EI
S
S
T
L
I
A
T
U
Y
Q
P
T
R
C
O
U
D
6
8
2
10
9
52
56
53
54
55
57
15
16
58
19
06
SHBRU KIT
22
59
DC
M
OTOR
C
LE E
OMP T
C
A
TTA ORS
A-100N
Page 17
REPLACEMENT PARTS LIST
A-002N-7T Pump Tube, Norprene .43 O.D., 1
31 C-330-6 Nut, Tube, .37 O.D. Tubing 1
36 C-335-6 Tubing, Outlet, .37O.D.X5ft, Poly 1
37 C-334-6 Tubing, Inlet, .37O.D.X5ft, Pvc 1
38 C-346 Weight, Inlet Tubing, Ceramic 1
39 C-342-2 Strainer, Inlet Tube, Polypro 1
40 71000-159 Roller, -4, -6 tubes (white rollers) 1
71000-255 Roller, -5 Viton tube 1
71000-350 Roller, -7 tubes (black rollers) 1
45 71000-156 Cover, P/head With Bearing 1
46 76001-003 Bearing, Sleeve, P/head Cover 1
48 90011-160 Screw, P/head Cover, 8-32 X .62 3
49 A-014N-6A Inj Valve, .5-.25 Mpt X .37 O.D. 1
50 90006-583 Motor Clip, 14, 30RPM 1
90006-601 Motor Clip, 45, 60RPM 1
51 90011-146 Screw, Motor Clip, 8-32 X .25 1
52 90007-515 Bushing, J-Box Connector, Alum. 1
53 76001-029 Junction Box, Valox 1
54 90011-129 Screw, 6-32 X .25 S Black 2
55 71000-133 Cover, J-Box w/Gasket &Label 1
56 70000-656 J-Box Assembly, Complete 1
N/s 90008-151 J-box Hole Plug .75 Dia Blk 1
57 A-022 Power Switch 1
N/s A-030 Push button prime switch 1
58 A-032 Knob, adjustment 1
59 90011-023 Screw, Motor, 8-32 x .50 Phill 2
60 C-1814N-2 Motor brush set, 90VDC motor 1
1 71000-214 Enclosure Back With Gasket, 1
2 90011-094 Washer, #10 Stainless 2
3 90011-091 Screw, #10 X 1.0” Phillips Steel 4
6 90006-580 Gasket, Back Plate, Neoprene 1
7 A-023N-B Percent timer (60 Sec), A-100NA 1
A-023N-H Percent timer (5 Sec), A-100NC 1
A-023N-F Percent timer (Spa), A-100NS 1
C-1817N-1 Speed Cntrl, A-100NF, 115V60 1
C-1817N-4 Speed Cntrl, A-100NF, 220V50 1
C-1817N-5 Speed Cntrl, A-100NF, 230V60 1
N/s 90010-036 Wire Nut, Blue 4
N/s 90010-037 Wire Nut, Orange 1
N/s 76001-030 Lead Wire, Blu/white, 115v 1
N/s 76001-031 Lead Wire, Red/white, 230v 1
N/s 76001-032 Lead Wire, Brn/white, 220v 1
N/s 76001-033 Lead Wire, Yellow, 220v 1
N/s 76001-034 Lead Wire, Black, 115v 1
9 90010-110 Power Cord, 115v60hz, 1
90010-196 Power Cord, 220v50hz, 1
90010-133 Power Cord, 230v60hz, 1
10 A-033N Cord Inlet Bushing 1
11 90003-559 Mounting Feet, Rubber 4
12 76001-000 Slide Clamp, Enclosure Rear 1
13 76000-999 Slide Clamp, Enclosure Front 1
14 71000-187 Encl, Percentage models - P/Cord 1
71000-188 Encl, Fixed model “X” - P/Cord 1
71000-219 Encl, percentage models - J-box 1
71000-220 Encl, Fixed feed model “X” J-box 1
15 90006-579 Gasket, Enclosure Front, Neoprene 1
16 90002-191 Door, Electronic Controls Cover 1
17 70002-146 Gearmotor, 14 Rpm, 115v60hz 1
70002-147 Gearmotor, 30 Rpm, 115v60hz 1
70002-156 Gearmotor, 45 Rpm, 115v60hz 1
70002-159 Gearmotor, 60 Rpm, 115v60hz 1
70002-148 Gearmotor, 14 Rpm, 220v50hz 1
70002-149 Gearmotor, 30 Rpm, 220v50hz 1
70002-157 Gearmotor, 45 Rpm, 220v50hz 1
70002-160 Gearmotor, 60 Rpm, 220v50hz 1
70002-150 Gearmotor, 14 Rpm, 230v60hz 1
70002-151 Gearmotor, 30 Rpm, 230v60hz 1
70002-158 Gearmotor, 45 Rpm, 230v60hz 1
70002-161 Gearmotor, 60 Rpm, 230v60hz 1
70002-241 G/motor, V/S 14Rpm, 90VDC 1
70002-242 G/motor, V/S 30Rpm, 90VDC 1
70002-243 G/motor, V/S 45Rpm, 90VDC 1
70002-244 G/motor, V/S 60Rpm, 90VDC 1
18 90006-581 Fan, Motor, 2.25” Diameter, 1
19 C-612PB Bearing Bracket With Bearing 2
20 C-616PN Rotor 14, 30RPM With Spacers 1
C-616PN-32 Rotor 45, 60RPM With Spacers 1
21 C-625 Screw, Motor, 14, 30RPM Phil 2
C-621-32 Screw, Motor, 45, 60RPM Phil 2
22 71000-211 Stator 14/30RPM, 115v Blu/Yel 1
71000-213 Stator 14/30RPM, 220v Brnt/yel 1
71000-212 Stator 14/30RPM, 230v Red/Yel 1
71000-466 Stator 45/60RPM, 115v Blut/Yel 1
71000-467 Stator 45/60RPM, 220v Brn/yel 1
71000-468 Stator 45/60RPM, 230v Red/Yel 1
90010-242 Motor, 90V Dc, model “F” 1
24 90011-078 Washer, Ground Screw, #8 Star 1
25 90010-126 Wire, ground, Green 1
26 A-008-1 Gearbox, 14 Rpm 1
A-008-2 Gearbox, 30 Rpm 1
A-008-3 Gearbox, 45 Rpm 1
A-008-4 Gearbox, 60 Rpm 1
27 76001-009 Pumphead, no TFD sensors 1
71000-488 Pumphead, w/TFD sensors 1
28 C-324N Screw, P/head, 10-32 X .50 4
29 A-031 Spacer, Rotor 1
30 A-002N-4T Pump Tube, Norprene .25 O.D., 1
A-002N-5T Pump Tube Viton, .31 O.D., 1
A-002N-6T Pump Tube, Norprene .37 O.D., 1
Item Part No Description Qty
Item Part No Description Qty Item Part No Description Qty
A-100N
LIMITED WARRANTY
Your new pump is a quality product and is warranted to be free of defects as set
down in this policy. All parts, including rubberized goods, and labor are covered
under warranty for 90 days from the date of purchase. Used peristaltic pump
tube assemblies are not warranted. Parts, excluding rubberized goods, are
covered under warranty for 12 months from the date of purchase.
Warranty coverage does not include damage to the pump that results from
misuse, carelessness, abuse or alteration. Only the repair or the replacement of
the pump is covered. Blue-White Industries does not assume responsibility for
any other loss or damage.
Warranty status is determined by the pump’s serial label and the sales invoice or
receipt. The serial label must be on the pump and the pump must be
accompanied by the sales invoice or receipt to obtain warranty coverage. The
warranty status of the pump will be verified by Blue-White or a factory
authorized service center.
Please be advised; injection and metering devices are not intended as a means of
treating water to render it suitable for human consumption. When used as
hypochlorinators, they are meant to destroy bacteria and algae contamination,
before it’s removal by filtration. Acid and soda injectors are used for PH control
(balance). Blue-White injectors are factory tested with water only for pressure
and performance. Installers and operators of these devices must be well
informed and aware of the precautions to be taken when injecting various
chemicals -especially those considered hazardous or dangerous.
Should it become necessary to return an injector for repair or service, you must
attach information regarding the chemical used as some residue may be present
within the unit which could be a hazard to service personnel.
Blue-White Industries will not be liable for any damage that may result by the
use of chemicals with their injectors and it’s components. Thank you.
PROCEDURE FOR IN WARRANTY REPAIR
Carefully pack the pump to be repaired, include the foot strainer and
injection/check valve fitting. Enclose a brief description of the problem as well
as the original invoice or sales receipt showing the date of purchase. The receipt
will be returned with the unit. Prepay all shipping costs. COD shipments will
not be accepted. Warranty service must be performed by the factory or an
authorized service center. Damage caused by improper packaging is the
responsibility of the sender.
Page 18 A-100N
Users of electrical and electronic equipment (EEE) with the WEEE marking per Annex IV of
the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste, but
use the collection framework available to them for the return, recycle, recovery of WEEE
and minimize any potential effects of EEE on the environment and human health due to the
presence of hazardous substances. The WEEE marking applies only to countries within the
European Union (EU) and Norway. Appliances are labeled in accordance with European
Directive 2002/96/EC.
Contact your local waste recovery agency for a Designated Collection Facility in your area.
ARKANSAS American Pump
BT Environmental, Inc 7580-A W. Tennessee St. NORTH CAROLINA
Bill Thomason Tallahassee, FL 32304 Southern Industrial Sales
225 Castleberry Street 904-575-9618 1903 Herring Avenue
Hot Springs, AR 71902 Wilson, NC 27893
Del Ray Electric
501-624-3837 919-237-2500
11 N.E. 2nd Avenue
CALIFORNIA (NORTHERN) Del Ray Beach, FL 33444
PENNSYLVANIA
407-278-3976
Howard E. Hutching co.
Armor Electric, Inc.
(Repair Center)
1425 Selinger Avenue
Jerry Lee Chemical Co.
7190 Penryn Plaza
Erie, PA 16505
3407 W. Old Fairfield Drive
Penryn, CA 95663 814-838-2034
Pensacola, FL 32505
Pool-Tech, Inc.
904-432-9929
SOUTH DAKOTA
3471 Mt. Diablo Blvd.
Son-Aqua Distributing
Lafayette, CA 94549 Picard Chemical
Jim Robinson
415-284-1400 1670 S. Congress Avenue
2447 W. Main Street
W. Palm Beach, FL 33406
Swimco Electric Co.
Rapid City, SD 57702
407-965-3434
753 Camden Avenue 605-343-7716
Campbell, CA 95008
V.J. Mini & Son, Inc.
408-378-2607 TENNESSEE
1581 N. Dixie Highway
Rock City Machine
CALIFORNIA (SOUTHERN) Pompano Beach, FL 33060
307 3rd Avenue South
305-946-0920
Blue-White Industries
Nashville, TN 37201
(Repair Center)
615-244-1371
ILLINOIS
5422 Business Drive
Mullarkey Associates
Huntington Bch. CA 92649
TEXAS
(Repair Center)
714-893-8529
Alamo Water Refiners
12346 S. Keeler Ave. 13700 Hwy. 90 West
COLORADO
Alsip, IL 60658 San Antonio, TX 78245
Denver Winpump
708-597-5558 512-677-8400
655 Depew Street
Lakewood, CO 80214-2494
MARYLAND EGCO Industries
303-233-1121
Century Pool Service, Inc 8505 Director Row
CONNECTICUT
5020 Nicholson Court, #201 Dallas, TX 75247
Cronin-Cook & Associates
Kensington, MD 20895 214-631-6885
24 West Road
301-231-8999
Vernon, CT 06066
Miracle Water Cond. Co.
203-875-0544
NEVADA Robert Shelton
Swim-In Enterprises, Inc. 1011 Oakmead Drive
FLORIDA
1314 S. Main Street Arlington, TX 76011
AAA Electric Motor Services
Las Vegas, NV 89104 817-640-6188
1131 N.E. 45th Street
702-384-4223
Ft. Lauderdale, FL 33334
305-772-7501
All American Pool & Patio NEW YORK
2021 Curry Ford Road
Sherwood Specialties, Inc.
Orlando, FL 32806
412 Smith Street
407-898-8722
Rochester, NY 14608
716-546-1211
Rice Pump & Motor Repair
5788 N. Powerline Road
Ft. Lauderdale FL 33309
305-776-6049
AUTHORIZED SERVICE CENTERS
Page 19A-100N
# 80000-327 Rev. 2/26/2007
5300 Business Drive
Huntington Beach, CA 92649
USA
Phone: 714-893-8529 FAX: 714-894-9492
E mail: sales@blue-white.com or techsupport@blue-white.com
Website: www.blue-white.com
Blue-White
Industries, Ltd.
R
Loading...