Bluestream HMXL44AB User Manual

HMXL44AB

User Manual

4x4 4K HDBaseT™ Matrix

HMXL44AB User ManUal

Surge protection device
recommended

This product contains sensitive electri­cal components that may be damaged
by electrical spikes, surges, electric
shock, lightning strikes, etc. Use of
surge protection systems is highly
recommended in order to protect and
extend the life of your equipment.

Best Cabling Practices

The transmission distances of HDMI
over UTP cables are measured using TE
CONNECTIVITY 1427071-6

EIA/TIA-568-B termination (T568B) for
LAN cables is recommended for better
performance.

To reduce the interference among the
unshielded twisted pairs of wires in
LAN cable, do not run HDBaseT / Zone
Cat5e/6/6a cabling with or in close par­allel proximity to mains power cables.

Do not substitute or use any other
Power Supply other than the enclosed
unit, or a Blusteam approved Replace­ment Part..

Do not disassemble either the Trans­mitter or Receiver for any reason.
Doing so will void the manufacturer’s
warranty.

Introduction 03

Features 03

Panel Descriptions 03/04

Remote Control Descriptions 04

Specifications 05

Package Contents 05

Maintenance 05

Application Diagram 06

RS-232 Pin Assignment 07

RS-232 and Telnet Commands 07

Contents

Thank you for purchasing
this product.

For optimum performance and safety,
please read these instructions care­fully before connecting, operating or
adjusting this product. Please keep this
manual for future reference.

02

www.blustream.co.uk

HMXL44AB User ManUal

Front Panel

1 2 4

11

5

12

6

13714815916

3

10

1 LCD display – Shows the status

of input-output selection, EDID
info etc.

2 IR receiver window
3 Power LED indicator
4 Power button – Press to power on/

o the matrix.

5 HDMI output selection button 1 to

4 - to select the output from 1 to 4.

6 All button for HDMI outputs – All

outputs will works as one. (Selects
all outputs)

7 Menu button – Press to enter EDID

set mode (see page 5)

8 Up selection button - Press to

change segment’s value.

9 ESC – Press to quit EDID set mode.
q Lock indicator
w Lock button – Press to lock the but-

tons of the front panel.

e HDMI input selection button 1 to 4 –

Press to select the input from 1 to 4.

r PTP button – Press to mirror all

inputs and outputs (e.g. output 1 to
input1, output 2 to input2)

t Selection button – Press to select

segment to change setting.
Selected segment will blink.

y Down selection button – Press to

change segment’s value.

u Enter button – Press to set EDID

to specified INPUT or copy EDID
from specified OUTPUT to
specified INPUT.

Our Essential 4x4 HDBaseT™ Matrix oers unprecedented performance and value for the
custom installation market. The HMXL44-KIT is a 4K 4x4 matrix package, delivering HDMI,
Bi-directional IR and PoH (PoE) up to lengths of 70m over a single CAT cable. The matrix
also provides advanced features including Audio breakout, simultaneous HDMI outputs
and RS-232 pass through to enable 3rd party control of displays. The HMXL44- KIT is
supplied with 4 x HEX70ED Receivers.

Introduction

FEATURES:

• Features 4x HDMI inputs which can
be independantly routed to 4x
HDBaseT™/HDMI outputs

• Simultaneous HDBaseT™ and HDMI
outputs to allow connection to dual
displays per zone

• HDMI audio de-embedded to
associated analogue L/R audio
outputs

• Extends up to distance of 70m over
single CAT cable

• Supports 4K UHD video up to 40m
(3840 x 2160 @30Hz 4:4:4, 4096 x 2160

@24Hz 4:4:4, and 4K @60Hz 4:2:0)

• Supports all industry standard video
resolutions including VGA-WUXGA
and 480i-4K

• Supports 3D signal display

• Supports all known HDMI audio
formats including Dolby TrueHD,
Dolby Atmos, Dolby Digital Plus and
DTS-HD Master Audio transmission

• Supports bi-directional IR from all
input and output locations

• Supplied with Blustream IR receivers
and emitters

• Control via front panel, IR, RS-232 and
TCP/IP

• Supports PoH (Power over
HDBaseT™) to power compatible
HDBaseT™ receivers

• 3rd Party drivers available for all
major home control brands

• Advanced EDID management

• HDCP compliant

• Matrix kit is supplied with 4 x RX70ED
HDBaseT™ receivers

• 1U Design for 19” rack mount
integration - mounting kit included

03

contact [e-mail] / [e-mail]