This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS U S ING OR
BAGEL
TOASTERS
Model:
BT-4C
Includes
INSTALLATION
USE & CARE
IMPORTANT: DO NOT DISCARD THIS MANUAL
this appliance. Additional manuals are available from your WELLS DEALER.
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
PRINTED IN UNITED STATES OF AMERICA
p/n 40091 Rev. G ECN-13372 M201 071026 cps
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship for
a period of one year from the date of original installation or
18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN
FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE, AND/OR FOR DIRECT,
INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed, or
if service is performed by unauthorized personnel. The
prices charged by Wells Bloomfield for its products are
based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of
defects without charge by a Wells Bloomfield factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
device with a cord and plug) must be taken or shipped to
the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
contained in this warranty, specific limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomfield
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
void elsewhere. Please consult your classified telephone
directory, your foodservice equipment dealer or contact:
Service Department, Wells Bloomfield, LLC
P.O. Box 280, Verdi, Nevada 89439
phone (775) 689-5707 or fax (775) 689-5976
for information and other details concerning warranty.
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
1. Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not covered by this warranty unless warranted conditions
are the cause.
2. All problems due to operation at voltages or phase other than specified on equipment nameplates are
not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.
3. All problems due to electrical connections not made
in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are
not covered by this warranty.
4. Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
5. Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
6. Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and
cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted for
ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This includes institutional and correctional facilities.
201 p/n 40091 OpM T-4C and BT-4C Toaster
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.
Wells Bloomfield cannot assume liability for damage or loss
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
xi
TABLE OF CONTENTS
WARRANTY xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS 2
PRECAUTIONS &GENERAL INFORMATION 3
AGENCY APPROVAL INFORMATION 3
INSTALLATION 4
OPERATION 5
CLEANING INSTRUCTIONS 6
TROUBLESHOOTING 7
PARTS & SERVICE 9
CUSTOMER SERVICE DATA 9
Thank You for purchasing this
Wells Bloomfield appliance.
Proper installation, professional
operation and consistent
maintenance of this equipment
will ensure that it gives you the
very best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this equipment, and to use
and care for the equipment in a
manner which will ensure its
optimum performance.
SPECIFICATIONS
DIMENSIONS:
Cabinet 12”H x 13-1/8”W x 9-1/16”D
Bread Slot 1-1/8” x 5-1/4”
Slices per Load1 to 4
ELECTRICAL:
MODEL VOLTS AMPS kW PLUG
T-4C 208V 11.5A 2.4 kW NEMA 6-15P
240V 10.0A 2.4 kW NEMA 6-15P
T-4C 15A 120V 15.0A 1.8 kW NEMA 5-15P
BT-4C 120V 13.3A 1.6 kW NEMA 5-15P
201 p/n 40091 OpM T-4C and BT-4C Toaster
1
FEATURES & OPERATING CONTROLS
SLIDE
KNOBS
(1 per 2
slots,
2 total)
DARKNESS
CONTROL
KNOBS
(1 per 2 slots,
2 total)
CRUMB
TRAY
Fig. 1 Toaster Features & Operating Controls
BREAD SLOTS
(4 total)
ELEMENTS
(2 per slot,
8 total)
CARRY
HANDLES
(1 each side)
POWER
CORD
BREAD GUIDES
(2 per slot,
8 total)
SLIDE
RACKS
(1 per 2
slots,
2 total)
INTERNAL COMPONENTS
BREAD SLOTS One to four pieces of bread, one slice of bread per slot.
Oversized to accept Texas toast, English muffin, bagel, etc.
BREAD GUIDES Hold bread at proper distance from elements
SLIDE RACKS Carriages hold bread slices for toasting
Controlled by slide knobs
ELEMENTS Provide toasting heat.
Note: Bagel toaster BT-4C toasts one side (cut side) only
One element in each pair is inert
DARKNESS Individually adjustable from very light to very dark
CONTROL Control time slide rack is down and elements are energized
KNOBS Each knob controls one pair of bread slots
SLIDE KNOBS Control slide racks. Initiate toasting timer when pushed
down. Each knob controls one slide rack (one pair of bread
slots)
POWER CORD Plugs into appropriate electrical receptacle
CARRY HANDLES Carry the toaster here
DO NOT carry the toaster by the bread slots!
CRUMB TRAY Crumbs accumulate here. Remove to dump crumbs
201 p/n 40091 OpM T-4C and BT-4C Toaster
2
PRECAUTIONS AND GENERAL INFORMATION
This appliance is intended for use in commercial establishments
only.
This appliance is intended
No other use is
agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Unplug or disconnect the toaster from electrical power before
performing any maintenance or servicing.
DO NOT submerge toaster in water. DO NOT splash or pour
water into bread slots, controls, control panel or wiring.
DO NOT lift or carry the toaster by the bread slots. Lift and carry
by the carrying handles only.
The technical content of this manual, including any wiring diagrams,
schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualified technical personnel.
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
recommended or authorized by the manufacturer or its
to prepare food for human consumption.
WARNING:
ELECTRIC SHOCK
HAZARD
All servicing requiring access
to non-insulated electrical
components must be
performed by a qualified
technician. DO NOT open
any access panel that
requires the use of tools.
Failure to follow this warning
can result in severe electrical
shock.
CAUTION:
RISK OF
DAMAGE
DO NOT connect and/or
energize this appliance until
all installation
instructions are read and followed. Damage to the
appliance will result if these
instructions are not followed.
AGENCY APPROVAL INFORMA TION
This unit complies with NSF standard 4 only if maintained and
operated per the instructions in this manual.
This unit is Underwriters Laboratory listed under E6070.
201 p/n 40091 OpM T-4C and BT-4C Toaster
STD 4
E6070
3
INSTALLATION
NOTE: DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the
inside front cover of this
manual.
DO NOT lift or carry the
toaster by the bread slots.
This will damage the
heating elements Lift and
carry by the carrying
handles only.
CAUTION:
ELECTRIC SHOCK
HAZARD
The ground prong of the power
cord is part of a system
designed to protect you from
electric shock in the event of
internal damage to the
appliance.
NEVER CUT OFF THE
GROUND PRONG
(large round prong).
NEVER TWIST A PRONG TO
FIT AN EXISTING
RECEPTACLE.
If circuit or receptacle does not
match the toaster plug, contact
a licensed electrician to install
an electrical receptacle
appropriate to the voltage and
amperage requirements of the
toaster.
IMPORTANT:
Damage due to being plugged
into the wrong voltage or
phase is NOT covered by
warranty
UNPACKING & INSPECTION
Carefully remove the toaster from the carton. Remove all
protective plastic film, packing materials and accessories from the
toaster before plugging the toaster into electrical power or otherwise
performing any installation procedure.
Carefully read all instructions in this manual and the Installation Instruction Sheet packed with the toaster before starting any
installation.
Read and understand all labels and diagrams attached to the
toaster.
Carefully account for all components and accessories before
discarding packing materials. Store all accessories in a convenient
place for later use.
SETUP
Setup the toaster only on a firm level surface. Non-combustible
material (e.g. metal, terrazzo) is recommended.
ELECTRICAL
Refer to the nameplate. Verify the electrical service power. Voltage
and phase must match the nameplate specifications. Plugging the
toaster into the wrong voltage can severely damage the equipment or
cause noticeably decreased performance.
Your appliance is equipped with a grounded electric power cord. This
cord must be plugged into a properly grounded electrical receptacle.
T-4C Toasters are equipped with a 4 foot cord with grounded NEMA
6-15P plug. This cord must be plugged into a 208 or 240 volt, 15 amp
circuit with a properly installed and grounded NEMA 6-15R
receptacle. Refer to toaster nameplate for proper voltage.
T-4C 15A Toasters and BT-4C Bagel Toasters are equipped with a 4
foot cord with grounded NEMA 5-15P plug. This cord must be plugged
into a 120 volt, 15 amp circuit with a properly installed and grounded
NEMA 5-15R receptacle.
201 p/n 40091 OpM T-4C and BT-4C Toaster
4
OPERATION
GENERAL OPERATIONAL NOTES
Carefully read the description of the toaster operation on the
specification sheet.
DO NOT attempt to perform any maintenance or service, or attempt
to unjamb a slice of toast unless the toaster is unplugged from
electrical power.
DO unplug the toaster from electrical power before cleaning, servicing
or unjamming.
DO NOT use sharp objects or metal implements to unjamb a slice of
toast.
DO use a plastic spatula inserted along the bread guides, away from
the elements, to remove toast that is jammed.
DO NOT lift or carry the toaster by the bread slots. This will damage
the elements.
DO carry the toaster by the carry handles.
OPERATION
Turn the darkness control knobs to the desired toast color. The knobs
may be rotated to the light position (fully counter-clockwise for very
little color) to the dark position (fully clock-wise for dark brown). There
are an infinite number of settings between these two extremes. Each
knob controls one pair of bread slots.
Experiment with your normal bread product and adjust the darkness
control knobs to the desired toast color.
Place one to four bread slices in the bread slots, one per slot. The
wide bread slots will accept other large size bread products, such as
buns, waffles, English Muffins, Texas-sized toast, etc. When using
non-standard bread products, be sure to adjust the darkness control
knob for your desired toast color.
Press down on the slide knobs until they stop. The slide rack should
move easily, and catch in the down position. Each slide knob controls
one pair of bread slots (i.e. right or left pair).
Toast time is approximately two minutes (Model T-4C), two or more
minutes (Model BT-4C) or three minutes (Model T-4C 15A). These
times are only approximate and will vary depending on the darkness
setting. Your own experience with your product is your best guide to
the best darkness setting.
The slide rack raises automatically at the end of the timed cycle. Slide
201 p/n 40091 OpM T-4C and BT-4C Toaster
racks may be manually raised at any time during the timed cycle by
lifting the slide knob.
Each successive toasting cycle will require less time as the toaster
chamber retains more heat. Adjust the darkness knob as requi red to
maintain your desired toast color.
CAUTION:
HOT SURFACE
Exposed surfaces
can be hot to the touch
and may cause burns.
LIGHTER
DARKER
fig. 2 Darkness Control
Note: Model BT-4C Bagel
Toaster toasts only one side
(cut side) of bagels or buns.
Place bagels or buns in the
toaster in right or left pairs
of bread slots with cut sides
facing each other.
5
CLEANING INSTRUCTIONS
CAUTION:
ELECTRIC
SHOCK HAZARD
Unplug toaster from electric
power before cleaning.
CAUTION:
BURN HAZARD
Allow toaster to cool
completely before
cleaning.
CAUTION:
ELECTRIC
Do not submerge toaster in
water.
SHOCK HAZARD
IMPORTANT: DO NOT spill
or pour water into bread slots,
slide slots or interior of
toaster.
IMPORTANT: DO NOT spill
or pour water into controls,
control panel or wiring.
DO NOT submerge toaster in
water. Damage to internal
components will occur.
Damage to internal
components from water
damage is not covered by
warranty.
PREPARATION
Unplug toaster from electrical power before cleaning.
Allow toaster to cool completely before cleaning.
FREQUENCY
Daily
TOOLS
Soft Brush
Clean Cloth or Sponge
Mild Detergent or Cleaner Formulated for Stainless Steel
Warm Water
CLEANING
Unplug toaster and allow to cool completely.
With the slide knobs in the up position, wipe both slide racks with a soft
brush to remove any remaining food particles. DO NOT attempt to
brush or clean elements.
Remove the crumb tray. Empty the crumb tray and wipe with a clean
cloth moistened with clean warm water.
Wipe the outer portions of the toaster cabinet with a clean soft cloth or
sponge, warm water and a mild detergent or cleaner formulated for
cleaning stainless steel.
Rinse by wiping toaster cabinet with a clean soft cloth or sponge
moistened with clean warm water.
Dry by wiping with a clean soft dry cloth.
201 p/n 40091 OpM T-4C and BT-4C Toaster
6
TROUBLESHOOTING
SYMPTOM
Toaster won’t heat
One or more sections
won’t heat
Slide knob won’t catch in
the down position
Slide rack won’t raise at
end of toast time
Toast or bagel too dark or
burnt
Toast or bagel too light
POSSIBLE CAUSE
Not plugged in, damaged plug or cord
or circuit breaker tripped
BT-4C Bagel Toaster
Damaged element or other internal
component
Latch contaminated with crumbs
Damaged internal components
Damaged internal components
Darkness control set too dark
Damaged internal components
Darkness control set too light
Damaged internal components
SUGGESTED REMEDY
Check plug and cord
Check / reset circuit breaker
Bagel Toaster toasts only one
side of bagel or bun
Contact Authorized Wells
Service Agency for repairs
Keep crumb tray clean
Contact Authorized Wells
Service Agency for repairs
Contact Authorized Wells
Service Agency for repairs
Adjust for desired darkness
Contact Authorized Wells
Service Agency for repairs
Adjust for desired darkness
Contact Authorized Wells
Service Agency for repairs
NOTE: There are no user
serviceable components in the
toaster. In all cases of damage
or component malfunction,
contact your Authorized Wells
Service Agency for repairs.
201 p/n 40091 OpM T-4C and BT-4C Toaster
7
NOTES
8
201 p/n 40091 OpM T-4C and BT-4C Toaster
PARTS & SERVICE
DESCRIPTION SERVICE
PART NO.
TOASTER STAND 20931
KNOB, DARKNESS CONTROL 60007
KNOB, SLIDE 60008
CRUMB TRAY 60037
IMPORTANT: Use only
factory authorized service
parts and replacement
filters.
For factory authorized
service, or to order factory
authorized replacement parts,
contact your Wells authorized
service agency, or call:
Wells Bloomfield, LLC
2 Erik Circle
P. O. Box 280
Verdi, NV 89439
Service Parts Dept.
phone: (775) 689-5707
fax: (775) 689-5976
Service Parts Department can
supply you with the name and
telephone number of the
WELLS AUTHORIZED
SERVICE AGENCY
nearest you.
CUSTOMER SERVICE DATA
RESTAURANT _____________________________ LOCATION _____________
INSTALLATION DATE ________________________ TECHNICIAN ___________
SERVICE COMPANY ________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. _______________
EQUIPMENT SERIAL NO. _______________
201 p/n 40091 OpM T-4C and BT-4C Toaster
VOLTAGE: (check one) 120 208 240
please have this information available if calling for service
9
Genuine Parts
Protect - YOU - All - Ways
SERVICE TRAINING - QUALITY SERVICE
CUSTOMER SATISFACTION
Commercial Food Equipment Service Association
Wells Bloomfield proudly supports CFESA
Commercial Food Equipment Service Association
SERVICE TRAINING - QUALITY SERVICE
CUSTOMER SATISFACTION
WELLS BLOOMFIELD, LLC
2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439
telephone: 775-689-5703
fax: 775-689-5976
www.wellsbloomfield.com
PRINTED IN UNITED STATES OF AMERICA
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.