Blomberg TKF 7449 Z, TKF 7449 S Operating Instructions

TKF 7449 TKF 7449 A TKF 7449 S TKF 7449 Z

Dryer Trockner

Read this manual prior to initial operation of the product!

Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference.

This User Manual will

• Help you use your machine in a fast and safe way.

• Read the User Manual before installing and starting your product.

• In particular, follow the instructions related to safety.

• Keep this User Manual within easy reach for future reference.

• Please read all additional documents supplied with your product. Remember that this User Manual is also applicable for several other models.

Explanation of symbols

Throughout this User Manual the following symbols are used:

A Important safety information. Warning for hazardous situations with regard to life and

property.

B Caution; Warning for supply voltage.

Caution; Warning for fire hazard.

Caution; Warning for hot surfaces.

Read the instructions.

C Useful information. Important information or useful hints about usage.

This appliance’s packaging material is recyclable. Help recycle it and protect the environment

by dropping it off in the municipal receptacles provided for this purpose. Your appliance

also contains a great amount of recyclable material. It is marked with this label to indicate

the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

2960310287_EN/270110.1615

1 Important safety information

This section includes safety information that will help protection from risks of personal injuries or materialistic damages. Failure to follow these instructions shall cause any warranty and reliability commitment to become void.

General safety

• Never place the machine on a carpet-

covered floor, otherwise, lack of airflow beneath the machine may cause electrical parts to overheat. This will cause problems with your machine.

• If the power cable or mains plug is

damaged, you must call Authorised Service Agent for repair.

• The product should not be plugged in

during installation, maintenance and repair works. Such works should always be made

by the technical service. Manufacturer

shall not be held responsible for damages arising from processes carried out by unauthorised persons.

• Connect the product to a grounded outlet

protected by a fuse of suitable capacity as stated in the technical specifications table.

• Operate your product at temperatures

between +5°C and +35°C.

• Do not use electrical devices in the

product.

• Do not connect the air exit of the product

to the chimney holes which are used for the exhaust fumes of the devices operating with gas or other types of fuel.

• You must provide enough ventilation in

order to prevent gases exiting from devices operating with other types of fuels including the naked flame from accumulating in the room due to the back fire effect.

• Always clean the lint filter before or after

each loading.

• Never operate your dryer without the lint

filter installed.

• Do not allow fibre, dust and dirt

accumulation around the exhaust exit and at adjacent areas.

• Power cable plug must be within easy

reach after installation.

• Do not use extension cords, multi-plugs

or adaptors to connect the dryer to power supply in order to decrease the risk of electric shock.

• Do not make any changes on the plug supplied with the product. If it is not

compatible with the socket, have a qualified electrician change the socket with a suitable one.

• Items cleaned or washed with gasoil/

fuel oil, dry-laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should not be dried in the product since they emit flammable or explosive vapor.

• Do not dry items cleaned with industrial

chemicals in the dryer.

• Do not dry unwashed items in the dryer.

• Items soiled with cooking oils, acetone,

alcohol, fuel oil, kerosene, stain remover, turpentine, paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer.

• Garments or pillows bolstered with rubber

foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads should not be dried in the dryer.

• Do not use fabric softeners and anti-static

products unless they are recommended by the manufacturers of the fabric softener or the product.

• This product must be grounded. Grounding installation decreases the risk of

electric shock by opening a path with low resistance for the electricity flow in case of

a malfunction or failure. Power cable of this

product is equipped with a conductor and a grounding plug that allows for grounding the product. This plug must be installed appropriately and inserted into a socket which is grounded in accordance with the local laws and regulations.

• Do not install the product behind a door

with a lock, sliding door or a door that has a hinge against the hinge of the dryer.

• Do not install or leave this product in

places where it will be exposed to outdoor conditions.

• Do not tamper with the controls.

• Do not perform any repair or part replacing

procedures on the product even if you know or have the ability to perform unless it is clearly suggested in the operating instructions or the published service manual.

• Inside and exhaust duct of the product

must be cleaned by the qualified service personnel periodically.

• Wrong connection of grounding conductor of the product can cause electric shock. If

you have any suspect about the grounding connection, have it checked by a qualified electrician, service representative or service personnel.

3 - EN

• Do not reach into the machine when the

drum is spinning.

• Unplug the machine when it is not in use.

• Never wash down the appliance with

water! There is the risk of electric shock! Always disconnect by unplugging from the mains before cleaning.

• Never touch the plug with wet hands.

Never unplug by pulling on the cable, always pull out by grabbing the plug only. Do not operate the machine if the power cable or plug is damaged!

• Never attempt to repair the machine

yourself, otherwise, you will be putting your life and others’ lives in danger.

• For malfunctions that cannot be solved by

following the information given in the safety

instructions:

Turn off the machine, turn off and contact

an authorised service agent.

• Do not stop the dryer before the drying

cycle comes to an end unless you will remove all laundry from the dryer fast in order to lay them and dissipate the heat.

• Remove the door of the drying

compartment before decommissioning or disposing of the product.

• The final step of the drying cycle (cool-

down cycle) occurs without applying heat to ensure that the items are left at a temperature that will not damage them.

• Fabric softeners or similar products should

be used as specified by the fabric softener instructions.

• Underwear that contains metal

reinforcements should not be placed in a dryer. Damage to the dryer can result if metal reinforcements come loose during drying.

• Check all garments for forgotten lighters,

coins, metal pieces, needles, etc. before loading.

• At times when your dryer is not in use or

after the laundry is taken out following the completion of drying process, turn off by

using the On/Off button. In cases when the On/Off button is on (while the dryer is energized), keep the door of the dryer

closed.

Intended use

• This product has been designed for domestic use. It should not be used for

other purposes.

• Use the product only for drying laundry

that are marked accordingly.

• Dry only those articles in your product that

are stated in this manual.

• This product is not intended to be used by

persons with physical, sensory or mental disorders or unlearned or inexperienced people (including children) unless they

are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product.

Children’s safety

• Electrical appliances are dangerous for the children. Keep children away from the

machine when it is operating. Do not let them tamper with the machine.

• Packaging materials are dangerous to children. Keep the packaging materials out

of reach of children or dispose them by classifying according to waste directives.

• Do not allow children sit/climb on or enter

in the product.

• Children should be supervised to ensure

that they do not play with the product.

• Close the loading door when you leave the

area where the product is located.

4 - EN

Technical Specifications

Filling capacity (Dry Laundry Weight Placed in the Dryer)

White / Colored / Cotton clothes

Synthetics max. kg 3,5

Shirt 30’

Jeans max. kg 4 Sport max. kg 4 Lingerie max. kg 1 Viscose max. kg 1,5

Mixed max. kg 4 Ventilation/Refreshing max. kg 7 / 3,5

Timer programmes max. kg 7 / 3,5 Woolens / Silks preparation max. kg 2 / 1

Shirts

Drying system Heat Pump, , Condenser, electronic, humidity control

Dimensions

Height / Height for fixed

installation

Width cm 59,5

Depth / Depth for under counter installation

Depth with door opened cm 106,5

Adjusting height of the feet cm 1,5

Weight without package kg 58

Ambient temperature (+ 5°C) , (+ 35°C)

Main Model Code B917H42

Electrical connection Voltage 230 V 50 Hz Power 1200 W

Fuse

Directly delivering the condensed water to outdoors

Hose diameter cm 1 Hose length max. cm 140 Highest point of the hose max. cm 80

Consumption values

Wardrobe dryness for cottons 7 1400 %50 1,88

Wardrobe dryness for cottons* 7 1000 %60 2,35 Iron dry for cottons 7 1000 %60 1,77

Wardrobe dryness for synthetics 3,5 800 %40 0,88

max. kg 7

max. 2

shirts

max. 6

shirts

cm 85,0 / 82,0

cm 60 / 58

(C-type

time

delaying)

Amount of

laundry (kg)

Spin Speed

(rpm)

0,5

1,5

10 A

Remaining

humidity

(%)

Power

(kwh)

Time

(minutes)

125

145

115

* : Energy Label standard programme (EN 61121:2005) All values given in the table have been fixed according to EN 61121:2005 Standard. Consumption values may deviate according

to the laundry type, spin speed, environmental conditions and voltage fluctuations.

5 - EN

2 Installation

Refer to the nearest Authorised Service Agent

for installation of your product.

C Preparation of location and electrical

installation for the product is under customer’s responsibility.

B Installation and electrical connections must

be carried out by a qualified personnel.

A Prior to installation, visually check if the

product has any defects on it. If so, do not

have it installed. Damaged products will cause risks for your safety.

Appropriate installation location

• Install the product in an environment which has no risk of freezing and is in a stable

and level position.

• Operate your product in a well ventilated,

dust-free environment.

• Do not block the air ducts in front of and

under the product with materials such as long pile rugs and wooden bands.

• Do not place your product on a long pile

rug or on similar surfaces.

• Do not install the product behind a door

with a lock, sliding door or a hinged door which can strike the product.

• Once the product is installed, it should stay

at the same place where its connections have been made. When installing the product, make sure that the rear wall of it does not touch anywhere (tap, socket, etc.) and also pay attention to install the product at a place where it will stay permanently.

BDo not place the product on top of the

power cable.

• Keep at least 1.5 cm distance to walls of

other furniture.

Under counter installation

• A special part (Part no: 295 970 0100)

replacing the top trim must be provided and installed by the Authorised Service Agent in order to use the machine under a

counter or in a cupboard. It should never

be operated without the top trim.

• Leave at least 3 cm of space between

the side and rear walls of the product and the walls of the counter/cupboard when installing your product under a counter or in a cupboard.

Mounting over a washing machine

• A fitting device should be used between

the two machines when installing above a

washing machine. The bracket (Part no.

296 280 0100 white/296 280 0200 grey) must be installed by the Authorised Service Agent.

• Place the product on a firm floor. If it will be

placed on top of a washing machine, the

approximate weight of both machines may reach 180 kg when they are full. Therefore, the floor must be capable of carrying the load on it!

Connection to water drain (Products with a condenser);

In products equipped with condenser unit,

water accumulated during the drying cycle accumulates in the water tank. You should drain accumulated water after each drying cycle. You can directly drain accumulated water through the water drain hose supplied with the product instead of periodically draining the water collected in the water tank.

Connecting the water drain hose:

1. Pull the hose out by its end to remove it

from the product. Do not use any tools to remove the hose. Attach the drain hose adaptor to the end of this hose.

2. Connect the special drain hose supplied with the product to the hose adaptor fitting.

3. Connect the other end of the drain hose directly to the wastewater drain or to the washbasin. The fitting must always be secured in every type of connection. Your house may flood if the hose comes out of its housing during water discharge.

C When you direct the water drain to outside,

“Water Tank” warning light will turn on at the end of each programme.

Important:

• The hose should be attached to a height of

maximum 80 cm.

• Make sure that the hose is not pinched or

bend.

• The end of the hose should not be bent,

it should not be stepped on and it must not be folded between the drain and the product.

6 - EN

Adjusting feet

In order to ensure that your product operates

more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet.

Rotate the feet to adjust until the machine

stands level and firmly.

C Never unscrew the adjustable feet from

their housings.

Electrical connection

Connect the machine to a grounded outlet protected by a fuse of suitable capacity as

stated in the technical specifications table. Our

company shall not be liable for any damages that will arise when the machine is used on a circuit without grounding.

• Connection must comply with national

regulations.

• If the current value of the fuse or breaker

in the house is less than 10 Amps, have a qualified electrician install a 10 Amp fuse.

• Power cable plug must be within easy

reach after installation.

• The voltage and allowed fuse or breaker

protection are specified in the “Technical Specifications” section.

• The specified voltage must be equal to

your mains voltage.

• Do not make connections via extension

cables or multi-plugs.

• The main fuse and switches must have a

contact distance of minimum 3 mm.

B Damaged power cable must only be

replaced by a qualified electrician.

B If the product is faulty, it must not be

operated unless it is repaired! There is the risk of electric shock!

First use

• To have the product ready for operation

before calling the authorised service agent, make sure that its location and power

supply installations are appropriate. If they

are not, call a qualified electrician to have any necessary arrangements carried out.

• Make sure that the power connections of

the product are in accordance with the instructions given in relevant chapters of this manual.

Disposing of packaging material

Packaging materials are dangerous to children. Keep packaging materials in a safe place out of reach of children. Packaging materials of

your product are manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste.

Transportation of the machine

1. Unplug the machine from the mains.

2. Remove the water drain (if any) and

chimney connections.

3. Drain water remained in the machine completely before transportation.

Disposing of the old machine

Dispose of your old machine in an environmentally friendly manner.

Refer to your local dealer or solid waste

collection centre in your area to learn how to dispose of your machine. Before disposing of your old machine, cut off the power cable plug and make the loading door lock unusable to avoid dangerous conditions to children.

7 - EN

3 Initial preparations for drying

Things to be done for energy saving:

• Make sure that you operate the product

at its full capacity but pay attention to not exceeding it.

• Spin your laundry at the highest speed

possible when washing them. Thus, the drying time is shortened and energy consumption is decreased.

• Pay attention to dry same types of laundry

together.

• Follow the instructions in the user manual

for programme selection.

• Make sure that sufficient clearance is

provided at the front and rear side of the dryer for air circulation. Do not block the grill at the front side of the product.

• Do not open the door of the machine during drying unless necessary. If you must

certainly open the door, pay attention not to keep it open for a long time.

• Do not add new (wet) laundry during

drying.

• Lint and fibres released from the laundry to

the air during the drying cycle are collected

in the “Lint Filter”. Make sure that you clean

the filters before or after each drying.

• In models with condenser, make sure that

you clean the condenser regularly at least once every month or after every 15 drying cycles.

• In vented models, follow the chimney

connection rules in the user manual and pay attention to the chimney cleaning.

• Ventilate the room, where the dryer is

located, well during drying.

• For power saving in models with lamps, at

times when your dryer is not in use, keep

the door closed if the On/Off button is pressed (if the dryer is energized).

Laundry suitable for drying in the machine

C Always follow the suggestions on the

laundry labels. Dry only the laundry having a label stating that they are suitable for drying in a dryer and make sure that you select the appropriate programme.

A B C

l mn

o p q

Laundry unsuitable for drying in the machine

• Laundry items with metal attachments

such as belt buckles and metal buttons can damage your dryer.

• Do not dry items such as woollens, silk

garments and nylon stockings, delicate embroidered fabrics, laundry with metal accessories and items such as sleeping bags in the dryer.

• Laundry made of delicate and valuable

fabrics as well as lace curtains can be creased. Do not dry them in the dryer!

• Do not dry items made of hermetic fibres

such as pillows and quilts in the dryer.

• Laundry made of foam or rubber will be

deformed.

• Do not dry laundry containing rubber in the

dryer.

• Do not dry laundry exposed to petroleum,

oil, combustible or explosive agents in the dryer even if they are washed beforehand.

• Overly wet laundry or laundry with dripping

water must not be put into the dryer.

• Items cleaned or washed with gasoil/

• Do not dry items cleaned with industrial

chemicals in the dryer.

• Do not dry your unwashed laundry in the

dryer.

• Items soiled with cooking oils, acetone,

alcohol, fuel oil, kerosene, stain remover, turpentine, paraffin and paraffin removers

8 - EN

must be washed in hot water with plenty of detergent before being dried in the dryer.

• Garments or pillows bolstered with rubber

foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads should not be dried in the dryer.

• Do not use fabric softeners and anti-static

products unless they are recommended by the manufacturers of the fabric softener or the product.

• Do not dry the underwear reinforced with metal parts in the dryer. If these metal

reinforcements loosen and break during drying, they will damage your dryer.

Preparing laundry for drying

• Check all laundry items before loading

them into the product to make sure that there are no lighters, coins, metal items, needles and etc. in their pockets or on any part of them.

• Fabric softeners and similar products

must be used in accordance with the instructions of the manufacturer of the relevant products.

• All laundry must be spun at the highest

spin speed that your washing machine allows for the laundry type.

• Laundry may be tangled after washing.

Separate your laundry before placing them into your dryer.

• Sort your laundry according to their types

and thicknesses. Dry the same type of

laundry together. E.g.: fine kitchen towels

and table cloths dry faster than the thick bath towels.

Correct load capacity

C Adding laundry to the machine more

than the level shown in the figure is not recommended. Drying performance will degrade when the machine is overloaded. Furthermore, your dryer and your laundry can be damaged.

C Place your laundry into the drum loosely so

that they will not get tangled.

CLarge pieces (E.g.: bed sheets, quilt covers,

large tablecloths) may bunch-up. Stop the dryer 1-2 times during drying process to separate bunched-up laundry.

Following weights are given as examples.

Home articles

Cotton quit covers (double) 1500 Cotton quit covers (single) 1000 Bed sheets (double) 500 Bed sheets (single) 350 Large tablecloths 700 Small tablecloths 250 Tea napkins 100 Bath towels 700

Hand towels 350

Garments

Blouses 150 Cotton shirts 300 Shirts 200 Cotton dresses 500 Dresses 350 Jeans 700 Handkerchiefs (10 pieces) 100

T-Shirts 125

Approximate

weights (g)

Approximate

weights (g)

A Consider the information in the

"Programme Selection Table". Always start

the programme in accordance with the maximum load capacity.

• Open the loading door.

• Place laundry items loosely into the dryer.

• Push the loading door to close. Ensure that

no items are caught in the door.

9 - EN

4 Selecting a Programme and Operating Your Machine

Control panel

9 6

2 3

1. Washing machine spin speed*/ Timer

programme selection

Spin speed used to spin the laundry in the

washing machine / Indicates the time for

timer programs.

2. Display

Indicates the status of the machine.

3. Start/Pause/Cancel button

Used to start, pause or cancel the

programme.

4. Programme selection knob

Used to select a programme.

5. On/Off button

Used to turn on and off the machine.

6. Anti-creasing

Prevents the laundry from creasing after the

machine completes its programme.

7. Dryness level

Used to adjust the required dryness level.

8. Cancel audio warning

Used to cancel the audio warning given at

the end of the programme.

9. Time delaying buttons

Used to set the time delay.

Spin speed / Timer programs  Operation icon Pause icon Water tank full warning icon Filter cleaning warning icon Condenser cleaning warning icon Remaining time indicator

 Spin speed is used to show the remaining time more accurately. It does not affect the performance of your machine.

10 - EN

Child-proof lock warning icon Time delaying mode Door open warning icon Anti-creasing mode Audio warning level / Cancel audio warning Drying degree Anti-creasing is activated

Preparing the machine

1. Plug in your machine.

2. Place the laundry in the machine.

3. Press the “On/Off” button.

C Pressing the “On/Off” button does not

necessarily mean that the programme has

started. Press "Start/Pause/Cancel" button

of the machine to start the programme.

Programme selection

Decide the appropriate programme from the table below which includes drying temperatures in degrees. Select the desired programme with the programme selection knob.

Drying at high temperature only for cotton laundry.

Extra dry

Wardrobe dry

Iron dry

Thick and multi layered

laundry (E.g.: towels,

linens, jeans) are dried in a way that they do not require ironing before placing in the wardrobe.

Normal laundry (E.g.:

tablecloths, underwear) are dried in a way that they do not require ironing before placing in the wardrobe.

Normal laundry (E.g., Shirts, dresses) are dried ready to be ironed.

C For further programme details, see,

"Programme Selection Table"

Main programmes

Depending on the type of laundry, the following

main programmes are available:

•Cottons

You can dry your durable laundry with this

programme. Dries at high temperature. It is

recommended to use for your cotton items (such as bed sheets, quilt cover, underclothing, etc.).

•Synthetics

You can dry your less durable laundry with this

programme. It dries at a lower temperature compared to the cottons programme. It is

recommended for your synthetic laundry (such as shirts, blouses, synthetic/cotton blended laundry, etc.).

C Do not dry curtains and lace in your

machine.

Special programmes

For special cases, there are also extra

programmes available:

C Additional programmes may differ

according to the model of your machine.

•Shirt 30’

You can use this programme to dry your cotton laundry that you have spun at high speeds in

your washing machine. This programme dries

0.5 kg cotton laundry (2 Shirts) in 30 minutes.

C To obtain better results from your

dryer, your laundry must be washed at suitable programmes and spun at the recommended spin speeds in the washing machine.

•Shirts

This programme dries the shirts more sensitively and creases them less and thus, helps to iron them more easily.

C There may be a little humidity on your

shirts at the end of the programme. We recommend you not to leave the shirts in the dryer.

•Jeans

You can use this programme to dry your jeans that you have spun at high speeds in your washing machine.

C Review the relevant section in the

programme table.

•Mixed

Used to dry synthetic and cotton laundry that do not release colour. Used for laundry that is

suitable for drying.

•Sport

Used to dry the laundry that are made of

synthetic, cotton or mixed fabrics and have a tag indicating that they are suitable for drying.

•Silk preparation

You can use this function to ventilate your laundry and to decrease creasing. Do not use this function to dry your laundry completely. Take out your laundry and ventilate them immediately after the program is over.

•Woolen preparation

You can use this function to ventilate and soften your woolen laundry that can be washed in the washing machine. Do not use this function to dry your laundry completely. Take out your laundry and ventilate them immediately after the program is over.

•Lingerie

Suitable to dry the 100% synthetic or synthetic-mixture satin type underwear (night gown, garments for upper body, pajamas) with the word dryable in the washing instructions.

Products with a high accessory content such

as lace, veil, stone, beads and wires and products with a high content of silk should not be dried. The silk laundry with cotton content or satin look may remain wet when dried with this program. The level of dryness may depend on the mixture of the cloth, type of knitting and the humidity content.

11 - EN

•Viscose

You can dry your Viscose laundry that marked as it can dry in tumble dryer(dresses, shirts, underwear, etc…). Viscose/polymer, viscose/ cotton mixed laundry is also suitable for this program.

C It is not recommended to dry laundry

that has accessory of pile textile, lace, small stones etc… Drying level can be changeable according to the type and mixture of laundry.

•Ventilation

Only ventilation is performed for 10 minutes

without blowing hot air. You can air your clothes that have been kept at closed environments for a long time and deodourise unpleasant odours thanks to this programme.

•Timer programs

You can select one of the 10 min., 20 min., 30 min., 40 min., 50 min., 60 min., 80 min., 100 min., 120 min., 140 min. and 160 min. timer programmes to achieve the desired final drying

level at low temperatures. Programme dries

at the selected time regardless of the drying temperature.

Time display

The display shows the time remaining for the programme to complete while a programme is running. Time is displayed in hours and minutes

as “02:30”. The exemplary display image shows

the dryer when it is running and child-proof lock is active.

C Programme duration may differ from the

values in the consumption table subject to the changes in the water hardness and temperature, ambient temperature, type and amount of laundry, auxiliary functions selected, and changes in the supply voltage..

12 - EN

Programme selection and consumption table Programme table

Symbol Programme Laundry type Capacity

Cottons

Extra dry

Synthetics

Special programmes

Timer Programmes

Iron dry

Wardrobe dry

Iron dry

Shirt 30’ For your cotton and synthetic shirts (Max. 2 shirts) 0.5

Silk preparation For your silk clothes 1

Woolens preparation

Shirts For your cotton shirts (Max. 6 shirts) 1.5 Mixed For your cotton and synthetic laundry 4

Sport

Lingerie

Jeans For your jeans 4

Viscose For viscon and modal mixed laundry that bear a dryer label 1.5

Ventilation To ventilate laundry and remove odors, e.g., tobacco odor 7 / 3.5

160 minutes

140 minutes

120 minutes

100 minutes

80 minutes

60 minutes

50 minutes

For durable laundry, e.g., bed sheet, towel, bathrobe, underwear

For your synthetic clothes that are not resistant to high heat, e.g., shirts, blouses, clothes with synthetic blends

For cotton laundry that has a dry cleaning label 2

For textiles that does not keep water and for cotton garments with dryer label

For underwear that are 100% synthetics or that contain synthetics and bear a dryer label

To dry wet clothes in little amount within the desired time, 7 / 3.5

7Wardrobe dry*

3.5

40 minutes

30 minutes

20 minutes

10 minutes

* : Energy Label standard programme (EN 61121:2005) All values given in the table have been fixed according to EN 61121:2005 Standard. These values

may deviate from the table according to the laundry type, laundry spin speed, environmental conditions and voltage fluctuations.

** : Times on the display may change depending on the drying time.

13 - EN

Auxiliary function

Audio Warning

Cancel

audio warning

Audio warning

level 1

Audio warning

level 2

Audio warning

level 3

Your dryer will give an audio warning when the

programme comes to an end. If you do not want to hear this buzzing or want to change the

volume level, you need to press the “Volume level” button. No audio warning will be given when “x” appears on the screen.

C You can select this function either before or

after the programme starts.

Drying degree

Used to adjust the required dryness level. More drying is performed compared to the

default settings when “+” sign appears and less drying is performed when “-” sign appears.

Programme duration can change depending on

the selection.

A This function must be selected before the

programme starts.

Anti-creasing

process is complete.

Perform the same procedure to revert back to

the previous contrast setting.

Warning indicators

C Warning indicators may differ according to

the model of your machine.

Filter cleaning

A warning symbol will appear to remind filter cleaning after the programme finishes.

C f the filter cleaning symbol flashes

continuously, please refer to “Suggested solutions for problems”.

Water tank

A warning symbol will turn on at the end of the programme or when the tank is full with water. The machine stops operating if the warning symbol turns on when a programme is running. To restart the machine, please drain

the water in the water tank. Press “Start/Pause/

Cancel” button to start the programme after you have emptied the water tank. The warning symbol turns off and the programme resumes operating.

Cleaning the condenser

A 2-hour anti creasing programme to prevent laundry from creasing will be activated if you do not take the laundry out after the programme is over. This programme rotates the laundry in

60-second intervals to prevent creasing. Press

“Anti-creasing” button to activate. Anti-creasing is activated but the programme is running in the first exemplary figure. Drying is over and the first step of anti-creasing has started in the second figure.

Changing the contrast

Contrast can be adjusted in order to make the

symbols on the display appear clearer. It may

particularly be necessary to change the contrast setting of the display when the dryer is installed over a washing machine.

Press and hold the Spin Speed/Time button for

3 seconds. When the contrast is changed at the end of 3 seconds, all symbols on the display will become visible for 3 seconds in order to indicate that the

14 - EN

Warning symbol turns on with certain intervals to remind that the condenser needs cleaning.

Door open

Door of the dryer may be open. Latch of the condenser may be open.

+ 30 hidden pages