Blomberg DWT81900SS, DWT81800SSIH User Manual
Dishwasher
Installation Manual
DW 51600 SS
DW 51600 FBI
DWT 51600 SS
DWT 51600 FBI
DWT 81800 FBI
DWT 81800 SS
DWT 81800 SSIH
DWT 81800 SSWS
DWT 52600 WIH
DWT 52600 SSIH
DWT 52600 BIH
DWT 52800 WIH
DWT 52800 SSIH
DWT 81900 FBI
DWT 51600 W
DWT 81900 SS
Dishwasher
Installation Manual
DW 51600 SS
DW 51600 FBI
DWT 51600 SS
DWT 51600 FBI
DWT 81800 FBI
DWT 81800 SS
DWT 81800 SSIH
DWT 81800 SSWS
DWT 52600 WIH
DWT 52600 SSIH
DWT 52600 BIH
DWT 52800 WIH
DWT 52800 SSIH
DWT 81900 FBI
DWT 51600 W
DWT 81900 SS
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.
INTRODUCTION 1
1. IMPORTANT SAFETY INSTRUCTIONS 1
1.1 INSPECT THE DISHWASHER 2
2. TOOLS WHICH MAY BE NEEDED 3
3. MATERIALS WHICH MAY BE NEEDED 3
4. MATERIALS SUPPLIED 4
4.1 PARTS SUPPLIED 4
4.2 MANUAL BAG 4
4.3 DISHWASHER PARTS BAG 1 4
4.4 DISHWASHER PARTS BAG 2 4
4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 4
5. DISHWASHER SPECIFICATIONS 5
5.1 TECHNICAL FEATURES 5
6. ENCLOSURE PREPARATION 6
6.1 ELECTRICAL PREPARATION 6
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS 6
6.3 ADJUSTING HEIGHT 9
6.4 INSTALLING THE SIDE TRIM STRIPS 9
6.5 PREPARING THE WATER CONNECTION (A) 10
6.6 DRAIN PREPARATION 10
6.7 STEAM PROTECTION FOIL 12
7. PLACEMENT OF DISHWASHER INTO THE OPENING 13
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 13
7.2 READJUSTING FOOT LEVELS 15
7.3 ADJUSTING THE MOVABLE TOE KICK 15
7.4 FIXING THE CABINET TO THE COUNTER 17
7.5 PREPARING THE TIMBER DOOR 18
7.6 PREPARING THE PRODUCT DOOR 19
7.9 INSTALLING THE TIMBER DOOR 20
7.10 FIXING THE TIMBER DOOR 20
7.11 FIXING THE TIMBER DOOR 21
7.12 ADJUSTING THE KICK PLATE 21
7.13 CONNECTION 22
8. INSTALLER CHECKLIST 23
9. SELF HELP HINTS: 23
INTRODUCTION
Please read this installation manual
and particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon also will provide important references.
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION:
Indicates a potentially hazardous situation
which, if not avoided, may result in injury.
It may also be used to alert against unsafe
practices.
NOTICE:
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the table-ware, the
equipment or the environment.
1. IMPORTANT SAFETY
INSTRUCTIONS
In addition to these instructions, the
dishwasher shall be installed:
• In accordance with all local codes or, in
absence of a local code,
• In the United States, with the National
Electric Code,
• In Canada, with the Canadian Electric
Code C22.1-latest edition/Provincial and
Municipal codes and/or local codes.
NOTICE :
Read these installation instructions
completely before installing and follow them
carefully. Save these installation instructions
and pass them on to any future user.
WARNING
When installing the dishwasher, follow
basic precautions, including the
following:
• The dishwasher could only be converted
from cord-connected to permanently
connected by an authorized service
representative. (If needed contact your
dealer to schedule an authorized service
agent for conversion with an appropriate
conversion kit)
• Installation and repair should be
performed by a qualied installer.
Work by unqualied persons could be
dangerous and may void the warranty.
NOTICE :
The dishwasher should be installed by
an insured licensed plumber, contractor
or trained installer. Installation performed
by persons other than this could result in
improper installation and property damage.
• Do not operate the appliance if damaged,
malfunctioning, partially disassembled or
if it has missing or broken parts.
• Also follow the safety instructions of the
user manual.
• To reduce the risk of electric shock, re,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
• Only connect the dishwasher to the
power supply when all installation and
plumbing work is complete.
• If the dishwasher is installed in a location
that experiences freezing temperatures
(e.g. in a vacation home, cabin, etc.),
you must drain all the water from the
dishwasher’s interior. Water system
ruptures that occur as a result of freezing
are not covered by warranty.
• Dishwasher must be secured to adjacent
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
• Connect to a properly rated, protected
and sized power supply circuit to avoid
electrical overload. The dishwasher is
USA
1
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of # 16
AWG copper wire rated at 75 °C (167
°F) or higher. These requirements must
be met to prevent injury and machine
damage. Consult a qualied electrician if
in doubt.
• Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
• Ensure that any plastic wrappings, bags,
small pieces etc. are disposed of safely
and kept out of the reach of children.
Danger of suffocation!
• Remove the door to the washing
compartment when removing an old
dishwasher from service or discarding it.
Ensure that the appliance presents no
danger to children while being stored for
disposal.
• Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
NOTICE :
• The dishwasher drain hose must be
installed with a drain loop at least 28”
(710mm) off the cabinet oor; otherwise
the dishwasher may not drain properly.
• This dishwasher is intended for
residential use only, and should not be
used in commercial establishments.
• New installation - If the dishwasher is a
new installation, most of the work must
be done before the dishwasher is moved
into place.
• Replacement - If the dishwasher is
replacing another dishwasher, check
the existing dishwasher connections for
compatibility with the new dishwasher,
and replace parts as necessary.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior
to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic
damage. Report any damage immediately.
NOTICE :
• Cosmetic defects must be reported within
10 days of installation.
• Do not discard any bags or items that
come with the original package until
after the entire installation has been
completed.
USA
2
2. TOOLS WHICH MAY BE NEEDED
3. MATERIALS WHICH MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
Elbow with 3/8” N.P.T. male threads on one leg, and sized to t your water
supply line (copper tubing/compression tting, or braided hose) on the
other leg.
UL listed conduit connector or strain relief.
Teon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and ttings appropriate for hot water supply line (copper
tubing/compression tting, or braided hose).
Silicone
Glue
USA
3
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will
come in several plastic bags.
Check your parts bags shown
to make sure you have all the
parts as listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a
manual bag containing:
• User manual,
• Installation manual
4.3 DISHWASHER
PARTS BAG 1
This dishwasher bag comes
with the following parts:
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
d. Screws Ø 1/8” x 5/8” (Ø 3.5
mm x 14 mm)
e. Mounting Bracket Left
f. Mounting Bracket Right
h. Screw Clamp
k. Toe Kick Bracket - Left
l. Toe Kick Bracket – Right
n. Timber Centering
o. Timber Centering Screw
p. Toe Kick
s. Template
t. Hook and loop fastener
v. Side centering
z. Steam Protection Foil
4.4 DISHWASHER
PARTS BAG 2
(MODEL DEPENDING)
In addition to the manual bag
and the dishwasher parts bag
(dishwasher models which
can accept a wooden kitchen
door) also come with a door
panel installation kit which
contains:
y. Screws 4mm x 36 mm =
3/16th x 1-7/16th
4.5 PARTS ATTACHED
TO THE REAR OF THE
DISHWASHER
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
x6
USA
4
5. DISHWASHER SPECIFICATIONS
5.1 TECHNICAL FEATURES
Load capacity 14 place settings
Permissible water pressure 4.35 - 145 psi (0.3 - 10 bars)
Electrical connection 120 V (volts), 12 A (amps), 60Hz (hertz)
Total power 1400 W (watts)
Heater power 1100 W (watts)
NOTICE :
Because we continually strive to improve our products, we may change our specications
and design without prior notice.
This device corresponds to the following directives:
UL 749 Household Dishwasher directive.
USA
5
6. ENCLOSURE PREPARATION
6.1 ELECTRICAL PREPARATION
WARNING
The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or
breaker rated for 15 amperes.
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
WARNING
Dishwasher must be secured to adjacent cabinetry using the mounting brackets
provided. Failure to do this may cause damage to property or bodily injury.
e-f)
USA
6
Loading...