Blodgett VIB3870 Specifications
BLODGETT OVEN COMPANY
www.blodgett.com
1400 Toastmaster Drive, Elgin, IL USA 60120 • Phone: (847) 741-3300 • Fax: (847) 741-0015
Project
Item No.
Quantity
In-Vent
®
conveyor oven ventilation hood system.
All data is shown per oven section, unless otherwise indicated.
EXTERIOR CONSTRUCTION
Stainless steel exterior on front, sides, and ducts
Integral exhaust and make-up air plenum and duct collar assembly
Quick release duct fittings and duct extensions
Front air make-up cooling panels
Cooling fan motor exhaust plenum
Conveyor entrance/exit end exhaust plenums
Heat shields over end exhaust plenums and vertical exhaust corner riser
Stainless steel ceiling trim pieces included
INTERIOR CONSTRUCTION
Aluminized steel, 300 and/or 400 series stainless steel
Insulated supply ducting
OPERATION
Captures smoke, contaminants and cooking by-products emanating from
the oven.
Minimizes amount of tempered air removed from kitchen by surrounding
itself and oven with a layer of untempered make-up air.
Requires much less exhaust and make-up air flow than conventional
overhead hoods.
Exhausts grease and smoke from directly over conveyors resulting in
cleaner oven and environment.
Cooler surfaces lower radiant heat to room and increase operator safety
and comfort significantly
STANDARD FEATURES
Available in three configurations
VIB3870-1 for single MT3870 oven
VIB3870-2 for double stacked MT3870 ovens
VIB3870-3 for triple stacked MT3870 ovens
Fully detachable panels without tools
Quick disconnect ducting for servicing or cleaning
Adds only 4" to front-to-back dimensions
Ventilation system controls can be interlocked with the oven’s controls
Modular design for easier handling and cleaning
OPTIONS AND ACCESSORIES
(AT ADDITIONAL CHARGE)
Installation
VIB3870-1, VIB3870-2,
VIB3870-3
Single, Double, Triple
In-Vent
®
Hood System
In-Vent® Model VIB3870-1, VIB3870-2, VIB3870-3 for Blodgett Conveyor Oven MT3870
BLODGETT OVEN COMPANY
www.blodgett.com
1400 Toastmaster Drive, Elgin, IL USA 60120 • Phone: (847) 741-3300 • Fax: (847) 741-0015
VIB3870-1, VIB3870-2, VIB3870-3
DIMENSIONS:
Floor space 105.8" (2685mm) W x 68" (1727mm) D
AIRFLOW REQUIREMENTS:
Model Supply Exhaust
Duct Size (all models):12" x 12" (305mm x 305mm) 12" x 12" (305mm x 305mm)
VIB3870-1:
CFM: 1100 CFM 1500 CFM
Static Pressure: 0.02-0.03" W.C. (5-7 Pa) 1.5" W.C. (373 Pa)
VIB3870-2:
CFM: 1450 CFM 1850 CFM
Static Pressure: 0.09" W.C. (22 Pa) 1.4" W.C. (348 Pa)
VIB3870-3:
CFM: 1800 CFM 2200 CFM
Static Pressure: 0.12" W.C. (30 Pa) 1.8" W.C. (448 Pa)
MINIMUM ENTRY CLEARANCE:
Largest uncrated component
70" x 46.3" x 20" (1778mm x 1176mm x 508mm)
SHIPPING INFORMATION:
Weight:
VIB3870-1 380 lbs. (172 kg)
VIB3870-2 480 lbs. (218 kg)
VIB3870-3 580 lbs. (263kg)
Crate size:
VIB3870-1 Palletized size and number not yet finalized
VIB3870-2 Palletized size and number not yet finalized
VIB3870-3 Palletized size and number not yet finalized
Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY
NOTE: The company reserves the right to make substitutions of components without prior notice
APPROVAL/STAMP
P/N M10591 Rev A (7/01)
Provide Blodgett In-Vent® ventilation system, engineered for Blodgett model MT3870 conveyor oven. Exterior shall be stainless steel on front sides and ducts. Interior shall be of aluminized steel. Baffle grease filters shall be of galvanized steel or
aluminum construction. All exterior panels removable without the use of tools for access to mechanicals and cleaning. Integral
exhaust and make-up air plenums connected to stainless steel duct collars with quick disconnect assemblies. Ventilation system shall comply with ANSI/NSF-2 and UL-710. Provide factory authorized assembly and installation at additional cost, per
ANSI/NFPA-96. Ductwork between extension duct collars and rooftop equipment, and rooftop equipment not included.
Universal specification, based on specification sheet for
specific system with specific oven model.
SYSTEM OVEN MODEL
VIB3870-1, VIB3870-2, VIB3870-3 MT3870
SHORT FORM SPECIFICATIONS
Loading...