Blaupunkt Tw 1600.4 User Manual

Tw 1600.4
Recommended Woofer Enclosure
Sealed:
34
32.81
30 Hz
Sound | Subwoofer
Tw 1600.4
Blaupunkt India Private Limited
47, Atlanta Society, Nariman Point
Mumbai‐ 400 021. India. Toll Free: 1800 209 6820
info@blaupunkt.in | www.blaupunkt.com
Tw 1600.4
Tw 1600.4
Warranty
We provide a manufacturer's warranty for our products bought within India. You can view the warranty terms at
www.blaupunkt.com or ask for them directly at: Blaupunkt India Private Limited 47, Atlanta Society, Nariman Point, Mumbai ‐ 400 021. India.
Safety Notes:
Please observe the following safety notes during the installation & connection.
Ÿ Disconnect the negative terminal of the battery.
Observe safety notes of the vehicle manufacturer.
Ÿ Prior to drilling mounting holes, make sure that no
cables & parts of the vehicle will be damaged.
Ÿ Do not install subwoofers on loose rear parcel
shelves (fastback vehicles)
Ÿ Leave ample clearance between the cables and
other harnesses. Use cable glands for holes with sharp edges
Notes a bou t i n stal ling a su bwoo fer i n enclosures:
Before insta llin g the subwoofer in an enc losure guidelines, please observe some fundamental design instructions:
Ÿ Subwoofers with innite baffle can be installed in a
vehicle by simply using a wooden board trimmed to size which ensures an acoustic separation between the front and rear of a woofer. The wooden board is affixed in the boot under the rear shelf or at the back of the rear seat bench. Any existing air gaps should be sealed with sealing material.
Ÿ The shape of the enclosure plays a major role with
respect to the playback of low frequencies. However, try to avoid unusual shapes which require extensive work with respect to trimming and gluing.
Ÿ MDF boards or high-quality plywood made out of
birch with a thickness of 18 to 25mm are perfectly suited for building woofer enclosures.
Ÿ All abutting housing walls should be glued, screwed
together and sealed to avoid detachment due to vibration & external environmental inuences in a vehicle.
Ÿ To avoid vibration, stiffening ribs or bracing are used
for large woofer enclosures.
Ÿ Acoustic insulating material which lls the inside
volume to at least 20% increases the effective enclosure volume by 5 to 15%.
Ÿ The cables from the amplier to the subwoofer
should be kept as short as possible & have a cross section of at least 2.5mm .
2
Ÿ The nished subwoo fer enclosure should be
perfectly stable and airtight.
Ÿ If possible, use bass reex ports with a diameter of 7
to 10cm to avoid the port noise generally associated with smaller openings. PVC pipes are available commercially in different diameters. The pipe sections can be installed inside the enclosure using appropriate joints and ttings.
Ÿ Use an active (electronic) crossover, such as those
integrated into all Blaupunkt ampliers. The use of passive crossovers is not recommended.
Performance
Ÿ Maximum power handling (Watts): 1500 Ÿ Nominal power handling (RMS): 250W Ÿ Nominal impedance (Ohms): 4 Ÿ Frequency response (Hz): 30-300 Ÿ Efficiency (dB / 2.83V / 1m): 87dB Ÿ Diameter Installation hole (mm): 282 Ÿ Diameter Installation hole (inch): 11.1 Ÿ Thiele Small Parameter fs (Hz): 29.8 Ÿ Thiele Small Parameter Qts: 0.62z Ÿ Thiele Small Parameter Qes: 0.61 Ÿ Thiele Small Parameter Qms: 7.08 Ÿ Thiele Small Parameter Vas (l): 93.25 Ÿ Thiele Small Parameter Xmax (mm): 8 Ÿ Recommended sealed enclosure size: 1.2 cubic ft. (34 Liters)
Loading...