Blaupunkt ProComponent PCA2120, ProComponent PCA260 Owner's Manual

www.midwestelectronics.com

All power ratings conform to CEA-2006 standards.

PARAMETER/FEATURE PCA 260 PCA 2120

Channels 2/1 2/1

Size ( W x H x D) 10x1.9x8.5 inches (254x49x215mm) 10x1.9x11.6 (254x49x295mm)

Weight 4.8 lbs (2.2 kg) 5.6 lbs (2.5 kg)

Spade screw speaker terminals? YES YES

Maximum terminal wire size 14 ga. 14 ga.

Subsonic filter YES (10 Hz) YES (10 Hz)

Separate front/rear or left/right gains? NO NO

Fuse Type ATC spade -30A ATC spade -Two 25A

Speaker short, short to +12V, and short to ground protection? YES YES

High, low, and reverse voltage protection? YES YES

Power output transistors BTL BTL

Power supply transistors MOSFET MOSFET

Minimum speaker impedance (non-bridged) 2 ohms 2 ohms

(bridged) 4 ohms 4 ohms

PERFORMANCE DATA

Rated power output @ 0.1% THD, 14.4V (CEA-2006)

2 channels into 4 ohms / 2 ohms (watts rms) 2 x 60 W / 2 x 80 W 2 x 120 W / 2 x 180 W

1 channel into 4 ohms (watts rms) 1 x 150 W 1 x 300 W

Max Dynamic Power (watts rms) 200W 350W

Total Harmonic Distortion @ full power 0.1% THD 0.1% THD

Signal/Noise ratio (gain controls in center)

Measured @ 1 watt / 1 kHz dBA >80 >80

Measured @ full rated power (0.1% THD) dBA >97 >101

Damping factor >100 >100

Frequency response (full-range mode) 20 - 30,000 Hz 20 - 30,000 Hz

High-pass crossover frequency limits 50 H z - 250 Hz (variable), 12dB/oct 50 H z - 250 Hz (variable), 12dB/oct

Low-pass crossover frequency limits 50 H z - 250 Hz (variable), 12dB/oct 50 H z - 250 Hz (variable), 12dB/oct

Bass Boost Variable (0-12dB) Variable (0-12dB)

Input impedance 10 kohms 10 kohms

Input signal voltage control range 0.3 - 6.0 vrms 0.3 - 6.0 vrms

Current Draw @ 13.8 VDC (typical values @ X watts / Efficiency %)

@ full rated power, unbridged (@ 4 ohms) 17 A (50%) 30 A (52%)

@ 33% rated power, unbridged (@ 4 ohms) 9 A (35%) 15 A (50%)

@ idle (@ 4 ohms) 1.5 A 2 A

Minimum battery voltage to maintain rated power 13.8 VDC 13.8 VDC

Usable battery voltage 10 - 16 VDC 10 - 16 VDC

Trigger line voltage range 10 - 16 VDC 10 - 16 VDC

Trigger line current draw < 10 mA < 10 mA

Turn on delay time @ 2.0 seconds @ 2.0 seconds

Thermal shutoff temperature (average heat-sink temp) @ 85˚ C (185˚ F) @ 85˚ C (185˚ F)

NOTE: DUE TO ONGOING PRODUCT IMPROVEMENTS, DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE
WITHOUT ADVANCED NOTICE TO THE CONSUMER OR RETAILER.

B

LAUPUNKTSPECIFICATIONS

- PCA 260 & PCA 2120, 2/1 C

HANNELAMPLIFIERS

www.midwestelectronics.com

– 1 –

Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Concerns & installation warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

System planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Vehicle wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Connections & controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7

System configurations 1 & 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

System configurations 3 & 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Warranty information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Blaupunkt technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Assembly & Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

TABLE OF CONTENTS

Caractéristiques principales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Consignes de sécurité et avertissements relatifs à l’ installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Planification du système . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Outils d’installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Câblage du véhicule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Connexions & Commandes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17

Configuration des systèmes 1 et 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Configuration des systèmes 3 et 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Assistance technique de Blaupunkt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Assemblage & Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Couverture de dos

TABLE DES MATIÈRES

Características principales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Consideraciones de seguridad y precauciones en la instalación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Planificación del sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Herramientas de instalación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Alambrado del vehículo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Conexiones y Controles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27

Configuración de los sistemas 1 y 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Configuración de los sistemas 3 y 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Cuadro de solución de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Información de garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Apoyo técnico de Blaupunkt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Armadura y Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Portada Trasera

INDICE

Características-chave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Medidas de Segurança e advertências para a instalação . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Planejamento do sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Ferramentas para a instalação . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Fiação do veículo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Conexões e controles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-37

Configurações 1 e 2 do sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Configurações 3 e 4 do sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Quadro para solução de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Informações sobre a garantia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Assistência técnica da Blaupunkt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Montagem e instalarão . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tampa preta

ÍNDICE DAS MATÉRIAS

www.midwestelectronics.com

– 2 –

Congratulations! You are the now the owner of an exceptional car audio amplifier from the audio enthusiasts at

Blaupunkt. Our engineering staff has spent considerable time refining our PCA series amplifiers in order to introduce great
sound to the consumer at an affordable price. With these products we focus on sonic performance but balanced with
rugged design and flexible installation.

Not only do we offer you a great product but also a supportive owners manual. This manual can be used as a teaching
guide due to its brief, but informative, explanations of amplifier and system design. We are also very concerned about the
end consumer using proper installation techniques for the highest performance possible from their new audio products.
MOST important to us are the concerns with safety and the installation process. Since our Blaupunkt retail dealers have
the tools and experience for an optimized and safe installation, we always recommend they do the final vehicle integration.
But, should you choose to install these products yourself, please take the time to read this manual completely and abide
by all precautions.

THANK YOU FOR CHOOSING BLAUPUNKT!

PCA AMPLIFIER BENEFITS & FEATURES

There is a constant push for entry level amps to “play with the big dogs” yet for a low
price point. Rarely are they able to do so…. until now.

Rock solid Class AB designs ensure “in your face” sound with little fear
for reliability or performance. The rugged designs of the PCA
amp line, and their remarkable input frequency and gain
setting flexibility, enable nearly any system
configuration. Fat power and speaker leads make
sure all that power going in comes out the best
sound possible.

Should something go wrong in the installation, have
no fear. Protection for output short circuits and short
to grounds or 12 volts are all covered and a safety
“Protect” light lets you know. Peace of mind, and big
power, at low price points…look no further.

• Real, RMS watts. No need for “bogus” watts. This is the
real stuff in a great amp so there is no need to exaggerate - it
does what it says.

• Reinforced Class AB designs with reinforced output stages
ensure solid performance and reliability.

• Big heat sinks to ensure adequate heat dissipation regardless
of the load (they look cool too).

• Monster size, gold plated power and speaker
terminals for reliable, low resistance connections.

•Protection LED for notification should the unit shut
down due to installation problems.

• Wide range input voltages of 0.3-6.0Vrms.

• Continuously variable crossover frequency settings.

•2 ohm output stable (unbridged mode)

www.midwestelectronics.com

– 3 –

We always recommend you have your Blaupunkt amplifiers professionally installed but the
installation process is often so easy that the average consumer can achieve success with little
trouble. Regardless of the person installing, you should be sure to review the following points
before proceeding with the installation:

■

READ THE MANUAL! Understanding the product and installation limitations before

lifting a screwdriver.

■

WEAR SAFETY GLASSES AT ALL TIMES - Flying debris are always dangerous.

■

PROTECT THE VEHICLE - Always disconnect the negative battery cable before

starting any kind of installation work. This prevents a possible high current electrical
short (potential fires).

■

HEAT - Keep all audio components away from nearby hot vehicle components that heat up over time such as hoses,

high current wires, and braking system components.

■

GIVE YOURSELF LOTS OF TIME - Rushing to complete an installation nearly always ends up with problems.

■

DO NOT LISTEN AT HIGH SOUND LEVELS FOR A PROLONGED TIME - these amplifiers, used with high

efficiency speakers from ANY manufacturer, have the potential to cause permanent hearing loss after listening at
maximum volume levels for several hours.

SAFETY CONCERNS

Before disassembling your beautiful new car you need some basic installation knowledge and skill with common hand and
power tools. Following such basic installation tips and warnings will prevent possible damage to the vehicle and also
prevent possible fires.

■

AGAIN...READ THE MANUAL! There is a lot of helpful information in this manual that

will save time and prevent problems later.

■

COVER THE VEHICLE WORK AREAS - Use fender covers or blankets to protect the

work areas from scratches or dings.

■

DISCONNECT THE (-) LEAD ON THE BATTERY - No sparks or fires please!

■

“REVIEW” THE INSTALLATION - Before using any tools or moving vehicle

components, take five minutes to review the installation intentions (e.g., verify that an
amplifier will fit in an area of a car before tearing out all the interior).

■

“REVIEW” THE VEHICLE - Before drilling any holes or cutting into any surfaces, make

sure there are no fuel or hydraulic lines behind the surfaces. Also make sure there are no
wires routed directly behind or near the desired mounting area (remember...screws can
often extend 1-2 inches behind the mounting surface).

■

ENSURE PROPER FIT - Before cutting or drilling, make sure the amplifier will

physically fit in its desired location. Check for clearance around rear deck torsion bars or
other structural elements.

■

EVERY CAR IS ASSEMBLED DIFFERENT - Every auto manufacturer uses different

assembly techniques. Take care in removing/modifying all trim panels and mounting surfaces since they often use
unique screws or snap fasteners that are difficult to replace if they are lost or broken.

■

BE CAREFUL WITH CABLE ROUTING - When routing audio cables, make sure RCA and speaker wires are

routed away from high current power lines for audio amplifiers and vehicle systems lines when possible. This will
help prevent noises from creeping into the audio system, plus prevent potential damage to the vehicle wiring itself.

■

BE CAREFUL WITH ALL CONNECTIONS - When making connections, make sure each connection is clean

and properly secured. Observe all polarity markings carefully to ensure proper end performance.

■

CAUTION - FUEL TANKS AND FUEL LINES ARE NOW LOCATED DIRECTLY BENEATH THE REAR
DECK IN MANY CARS - CHECK FOR ADEQUATE CLEARANCE BEFORE EVEN CONSIDERING
SUCH A MOUNTING LOCATION!

INSTALLATION WARNINGS!

www.midwestelectronics.com