Blaupunkt 7644820310 User Manual
Radio / CD / MP3
Bremen MP74 7 644 820 310
Operating instructions
http://www.blaupunkt.com
http://www.blaupunkt.com
Open here
2
DEUTSCH
ENGLISH
2
3 4 5
1
6 7
8910111213
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
3
CONTROLS
1 Button, to switch the device on/
off,
and mute the device’s volume
2 Volume control
3
4 NEXT button to display the next
5 Softkeys, the function of the
6 DIS•ESC button to change the
7
8 Joystick and OK button
button, to unlatch the detach-
able control panel
pages of a menu,
and switch memory banks in radio mode
softkeys depends on what is currently being displayed
display content and close menus
button to open the detachable
control panel (flip-release panel)
9 MENU button to open the basic
settings menu (short press)
Activate/deactivate demo mode
(long press)
: AUDIO button to adjust the
bass, treble, balance, fader and
X-BASS (short press)
Access the DSA Max Equalizer
(Long press)
; Display
< SOURCE button to start CD /
CD-changer playback, start playing the Compact Drive MP3
(only if connected)
or
To play an external audio source
(only if connected)
= TUNER button to select radio
mode directly
To access the radio functions
menu (only possible in radio
mode)
58
CONTENTS
Notes and accessories .......... 61
Road safety ................................... 61
Safety notice ................................. 61
Installation ..................................... 61
Accessories .................................. 61
Activating /
deactivating demo mode................ 62
Theft protection ..................... 62
Detachable control panel ............... 62
Detaching the control panel ........... 62
Attaching the control panel ............ 63
Switching on/off .................... 63
Adjusting the volume ............. 64
Setting the power-on volume ......... 64
Volume mute ................................. 64
Telephone audio ............................ 64
Navigation audio ............................ 65
Sound and volume
distribution settings ............... 67
Adjusting the bass ......................... 67
Adjusting the treble ....................... 67
Adjusting the right/left volume
distribution (balance) ..................... 67
Adjusting the front/back volume
distribution (fader) ......................... 67
X-BASS .................................. 68
Adjusting the display settings 68
Radio mode ............................ 71
Adjusting the tuner settings ........... 71
Setting the number of antennas ..... 72
Switching to radio mode ................ 72
Selecting static/dynamic radio
mode (only FM) ............................. 72
Convenient RDS functions
(AF, REG) ..................................... 74
Selecting the waveband /
memory bank................................. 74
Tuning into a station ....................... 75
Setting the sensitivity of station
seek tuning.................................... 76
Scanning receivable stations
(SCAN) ......................................... 76
Setting the scanning time .............. 76
Storing stations ............................. 77
Storing stations automatically
(Travelstore) .................................. 77
Listening to stored stations ............ 77
Programme type (PTY) .................. 77
Optimising radio reception............. 79
Activating/deactivating the radio
text display .................................... 79
TIM -
Traffic Information Memory.... 80
Switching TIM on/off ..................... 80
Listening to stored traffic messages 81
Recording traffic information
messages...................................... 81
Setting the timers .......................... 82
Selecting a timer ........................... 82
Traffic information.................. 83
CD mode ................................ 84
Switching to CD mode and
inserting a CD ............................... 84
Ejecting a CD ................................ 84
Selecting tracks ............................ 84
Fast searching (audible) ................ 84
Random track play (MIX) ............... 85
Repeating tracks (REPEAT) ........... 85
Scanning tracks (SCAN) ............... 85
Displaying CD text ......................... 85
Setting scrolling text ...................... 86
Traffic announcements in CD mode. 86
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
59
CONTENTS
MP3 mode .............................. 86
Preparing an MP3-CD ................... 86
Switching to MP3 mode ................ 87
Selecting a directory...................... 88
Selecting tracks ............................ 88
Fast searching (audible) ................ 89
Scanning tracks (SCAN) ............... 89
Random track play (MIX) ............... 89
Repeating individual tracks or
whole directories (REPEAT)........... 89
Configuring the display .................. 90
CD-changer mode (optional) . 91
Switching to CD-changer mode..... 91
Selecting CDs ............................... 91
Selecting tracks ............................ 91
Fast searching (audible) ................ 91
Scanning tracks (SCAN) ............... 92
Repeating individual tracks or
whole CDs (REPEAT).................... 92
Random track play (MIX) ............... 92
Naming CDs ................................. 93
CLOCK time ........................... 94
Setting the clock time .................... 94
Displaying the clock time
continuously .................................. 95
DSA Max -
Digital Sound Adjustment ...... 95
Switching DSA on/off .................... 95
Automatically calibrating the
equalizer........................................ 96
Viewing the vehicle acoustics with/
without equalization ....................... 97
Adjusting the graphic equalizer
manually ........................................ 97
Selecting an equalizer ................... 98
Resetting the equalizer .................. 98
Selecting sound presets ................ 99
Setting the stage effect.................. 99
Selecting the sound effect ........... 100
DNC -
Dynamic Noise Covering...... 100
Calibrating DNC.......................... 100
Switching off DNC ...................... 101
Selecting the DNC boost............. 101
Subwoofer and centre
speaker ................................ 102
Adjusting the subwoofer boost
level ............................................ 102
Adjusting the subwoofer phase .... 102
Setting up the low-pass filter ....... 102
Setting up the subsonic filter ....... 103
Setting up the centre speaker ...... 103
Setting up the high-pass filter for
the front/rear channels................. 104
TMC for dynamic navigation
systems ................................ 105
Amplifier/sub-out ................. 105
External audio sources ........ 106
Switching the AUX input on/off .... 106
Naming the AUX input ................. 106
Entering the power-on
message .............................. 107
Displaying the serial number 108
Resetting the device ............ 108
Specifications ...................... 109
60
NOTES AND ACCESSORIES
Notes and accessories
Thank you for choosing a Blaupunkt
product. We hope you enjoy using this
new piece of equipment.
Please read these operating instructions before using the equipment for
the first time.
The Blaupunkt editors are constantly
working on making the operating instructions clearer and easier to understand. However, if you still have any
questions on how to operate the device,
please contact your dealer or the telephone hotline for your country . You will
find the telephone number printed at the
back of this booklet.
We provide a manufacturer guarantee
for our products bought within the European Union. You can view the guarantee conditions at www.blaupunkt.de
or ask for them directly at:
Blaupunkt GmbH
Hotline
Robert Bosch Str. 200
31139 Hildesheim
Germany
Road safety
Road safety has absolute priority. Only operate your car sound system if the road and traffic conditions
allow you to do so. Familiarise yourself with the device before setting off
on your journey.
You should always be able to hear
police, fire and ambulance sirens in
good time from inside your vehicle.
For this reason, listen to your car
sound system at a suitable volume
level during your journey.
Safety notice
The car sound system and the
device’s control panel (flip-release
panel) heat up during use.
Therefore, when removing the fliprelease panel, only hold it by its nonmetallic surfaces. Allow the car
sound system to cool down first if you
want to uninstall the whole unit.
Installation
If you want to install your car sound system yourself, please read the installation and connection instructions that
follow these operating instructions.
Accessories
Only use accessories approved by Blaupunkt.
Remote control
The RC 08, RC 10 or RC 10H remote
controls (available as optional accessories) allow you to access most of the
main functions of your car sound system safely and conveniently.
You cannot switch the device on/off using the remote control.
Amplifiers
You can use all Blaupunkt and V elocity
amplifiers.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
61
NOTES AND ACCESSORIES
THEFT PROTECTION
CD changers
You can obtain the following CD changers from accessory retailers for connection to this device: CDC A 03, CDC A 08
and IDC A 09.
Compact Drive MP3
You can connect the Compact Drive
MP3 instead of a CD-changer in order
to play MP3 music tracks. If you decide
to connect a Compact Drive MP3, you
will first need to use a computer to store
the MP3 music tracks on the Microdrive™ hard disk that is inside the Compact Drive MP3. Then, when the Compact Drive MP3 is connected to the car
sound system, you can play the tracks
like normal CD music tracks.
The Compact Drive MP3 is operated in
a similar way to a CD-changer. Most of
the CD-changer functions can also be
used with the Compact Drive MP3.
Activating / deactivating demo
mode
The device is supplied from the factory
with demo mode activated. The various
functions of the device are displayed
graphically as animations in the display
during demo mode. Y ou can also deactivate demo mode.
➮ Press and hold down the MENU
button 9 for longer than four seconds to activate/deactivate demo
mode.
Theft protection
Detachable control panel
Your device is equipped with a detachable control panel (flip-release panel) as
a theft protection measure.
The device is worthless to a thief without this control panel. Protect your device against theft by taking the control
panel with you whenever you leave your
vehicle. Do not leave the control panel
inside your vehicle - not even in a hiding place. The control panel has been
designed to be easy to use.
Note:
● Never drop the control panel.
● Never expose the control panel to
direct sunlight or other heat sources.
● Store the control panel in the sup-
plied case.
● Avoid direct skin contact with the
control panel’s electrical contacts. If
necessary, clean the contacts with
a lint-free cloth and some alcohol.
Detaching the control panel
3
62
➮ Press the button 3.
The control panel latch mechanism
opens.
THEFT PROTECTION
SWITCHING ON/OFF
➮ First, pull the control panel straight
off the device and then out towards
the left.
● The device switches off after the
control panel is detached.
● All the current settings are saved.
● Any CD already inserted in the de-
vice remains there.
Attaching the control panel
➮ Slide the control panel from left to
right into the device’s guide.
➮ Press the left edge of the control
panel into the device until it clicks
into place.
Note:
● When attaching the control panel,
make sure you do not press the
display.
Switching on/off
There are various ways of switching the
device on/off.
Switching on/off using button
1
➮ To switch on the device, press but-
ton 1.
The device switches on.
➮ To switch off the device, press and
hold down button 1 for longer
than two seconds.
The device switches off.
Switching on/off using the
vehicle ignition
The device will switch on and off simultaneously with the ignition if it is connected correctly to the vehicle’s ignition
and if it was not previously switched off
using button 1.
You can switch the device on even if
the ignition is off.
➮ Press button 1.
Note:
To protect the vehicle battery, the device will switch off automatically after
one hour if the ignition is off.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
63
PORTUGUÊS
DANSK
ADJUSTING THE VOLUME
Adjusting the volume
You can adjust the volume in steps from
0 (off) to 50 (maximum).
➮ To increase the volume, turn the
volume control 2 clockwise.
➮ To decrease the volume, turn the
volume control 2 anticlockwise.
Setting the power-on volume
You can set the default volume level at
which the device plays when it is
switched on.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “VOLUME” display item.
➮ Press the softkey 5 assigned to
the “ON VOL” display item.
➮ Set the volume level that you want
using the volume control 2.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Note:
You can also set the power-on volume
to be the same as the volume level that
was active before you switched off the
device. To do so, press the softkey assigned to the “LAST VOL” display item
in the volume menu.
Risk of injury! If the power-on
volume is set to maximum, the volume level can be very high when the
device is switched on.
If the volume was set to maximum
before the device was switched off
and the power-on volume is set to
“LAST VOL”, the volume level can
be very high when the device is
switched on again.
Severe damage to your hearing can
be caused in both cases!
Volume mute
You can instantaneously reduce the
volume (mute).
➮ Briefly press button 1.
“MUTE” appears in the display .
Cancelling mute
➮ Briefly press button 1 again.
or
➮ turn the volume control 2.
Telephone audio
If your car sound system is connected
to a mobile telephone, the sound system's volume will be muted as soon as
you “pick up” the telephone. The telephone call is then outputted over the car
sound system's loudspeakers. This requires that the mobile telephone is connected to the car sound system as described in the installation instructions.
If the sound system receives a traffic
announcement during a telephone call,
you will only be able to hear the traffic
announcement after the call is finished
(in so far as the traffic announcement is
still being broadcast).
64
ADJUSTING THE VOLUME
If a telephone call arrives during a traffic announcement, the traffic announcement will stop playing and you will hear
the telephone call instead.
You can set the volume at which you
want telephone calls to be initially heard.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “VOLUME” display item.
➮ Press the softkey 5 assigned to
the “PHONE” display item in order
to adjust the volume.
➮ Set the volume level that you want
using the volume control 2.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Note:
You can also adjust the volume during
the telephone call using the volume control 2.
Navigation audio
Instead of connecting a second external audio source (“AUX2”, see “External audio sources”) you can connect a
navigation system.
If your car radio is connected to a navigation system and the navigation system outputs spoken information, the
navigation voice output will be “mixed
in” with the current audio source and
will be outputted over the car radio’s
loudspeakers.
This requires that the navigation system is connected to the car radio (as
described in the installation instructions)
and activated in the menu.
You can find out from your Blaupunkt
dealer which navigation systems can be
used with your car sound system.
Activating navigation audio
You can either connect a second external audio source or a navigation system to this device. If you do, you must
specify which device is connected to this
connection by selecting it in the menu.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “AUX” display item.
The AUX menu is displayed.
➮ If you have a navigation system
connected, repeatedly press the
softkey 5 assigned to the “NAV/
AUX2” display item until the “NAVIGATION ON” setting appears.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
65
DANSK
ADJUSTING THE VOLUME
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Setting the minimum navigation
volume
You can set the volume level at which
the navigation voice output is “mixed in”
with the audio source.
Note:
● Set the volume on the navigation
system to maximum. If the output
sounds distorted, reduce the volume slightly on the navigation system.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “VOLUME” display item.
➮ Press the softkey 5 assigned to
the “NA VI DIFF” display item in order to adjust the volume.
➮ Set the volume level that you want
using the volume control 2.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Note:
● You can also adjust the volume
during the voice output using the
volume control 2. This setting
only applies to the current voice
output and is not saved.
66
SOUND AND VOLUME DISTRIBUTION SETTINGS
Sound and volume
distribution settings
Note:
You can adjust the bass and treble individually for each audio source.
Adjusting the bass
➮ Press the AUDIO button :.
“AUDIO MENU” appears in the display.
➮ Press the softkey 5 assigned to
the “BASS” display item.
➮ Move the joystick 8 up/right to
boost the bass or move it down/left
to reduce the bass.
When you have finished making your
changes,
➮ press the joystick OK 8 or the
AUDIO button :.
Adjusting the treble
➮ Press the AUDIO button :.
“AUDIO MENU” appears in the display.
➮ Press the softkey 5 assigned to
the “TREBLE” display item.
➮ Move the joystick 8 up/right to
boost the treble or move it down/
left to reduce the treble.
When you have finished making your
changes,
➮ press the joystick OK 8 or the
AUDIO button :.
Adjusting the right/left volume
distribution (balance)
➮ To adjust the balance, press the
AUDIO button :.
“AUDIO MENU” appears in the display .
➮ Press the softkey 5 assigned to
the “BALANCE” display item.
➮ Move the joystick 8 up/right or
down/left to adjust the right/left volume distribution.
When you have finished making your
changes,
➮ press the joystick OK 8 or the
AUDIO button :.
Adjusting the front/back volume
distribution (fader)
➮ To adjust the fader, press the AU-
DIO button :.
“AUDIO MENU” appears in the display .
➮ Press the softkey 5 assigned to
the “FADER” display item.
➮ Move the joystick 8 up/right or
down/left to adjust the front/back
volume distribution.
When you have finished making your
changes,
➮ press the joystick OK 8 or the
AUDIO button :.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
67
DANSK
X-BASS
ADJUSTING THE
DISPLAY SETTINGS
X-BASS
The X-BASS feature can be used to
boost the bass at low volume levels. Y ou
can set the X-Bass boost for one of the
following frequencies: 32 Hz, 40 Hz, 50
Hz, 63 Hz or 80 Hz in steps from 0 - 6. If
you select the 0 setting, the X-Bass
function will be deactivated.
➮ Press the AUDIO button :.
“AUDIO MENU” appears in the display .
➮ Press the softkey 5 assigned to
the “X-BASS” display item.
➮ Move the joystick 8 left or right to
select the frequency that you want
to boost.
➮ Move the joystick 8 up to boost
the X-BASS or move it down to reduce the X-BASS.
When you have finished making your
changes,
➮ press the joystick OK 8 or the
AUDIO button :.
Adjusting the display
settings
You can adjust the display settings to
suit the installation position in your vehicle and your own preferences.
Adjusting the viewing angle
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Press the softkey 5 assigned to
the “ANGLE” display item.
➮ Move the joystick 8 up/right or
down/left to adjust the viewing angle.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Adjusting the display brightness
If your car sound system is connected
as described in the installation instructions, the display brightness will change
when the headlights are turned on/off.
The display brightness can be adjusted
separately for night and day in steps
ranging from 1-16.
Display brightness
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Press the softkey 5 assigned to
the “BRIGHT” display item.
68
ADJUSTING THE DISPLAY SETTINGS
DAY and NIGHT are displayed in the
top display line together with the cur-
rently set values.
➮ Move the flashing selection marker
behind DAY or NIGHT by pressing
the joystick 8 to the left or right.
➮ Set the value that you want. To do
so, move the joystick 8 down or
up.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Setting the button illumination
colour
You can choose the colour of the device’s button illumination.
There are 16 colours for you to choose
from.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Press the softkey 5 assigned to
the “KEYCOLOR” display item.
➮ Move the joystick 8 up/right or
down/left to adjust the colour.
A different colour is selected every
time you move the joystick.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Setting the display illumination
colour
When setting the display illumination,
you can choose one of four preset colours or mix a colour yourself from the
RGB spectrum (red-green-blue) or select a colour during a colour scan.
Selecting a preset colour
Four different colours are already stored
in the device. “Ocean” (blue), “Amber”,
“Sunset” (red-orange) and “Nature”
(green) are available. Select a colour
that best suits your vehicle interior.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Press the softkey 5 assigned to
the “COLOR” display item.
➮ Press the softkey 5 assigned to
the display item of the colour that
you want.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Mixing a colour for the display
illumination
To customise the display illumination to
suit your tastes you can mix a colour
yourself using the three primary colours
red, blue and green.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
69
ADJUSTING THE DISPLAY SETTINGS
➮ Press the softkey 5 assigned to
the “COLOR” display item.
➮ Press the softkey 5 assigned to
the “USER” display item.
➮ In the following menu you can set
the red, blue and green colour
components yourself. To do so,
press the appropriate softkey 5
repeatedly until the displayed colour suits your tastes.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Selecting a display illumination
colour during a colour scan
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Press the softkey 5 assigned to
the “COLOR” display item.
➮ Press the softkey 5 assigned to
the “COL-SCAN” display item.
The device starts changing the display
illumination colour.
➮ If you want to select one of the col-
ours, press the softkey 5 assigned to the “SA VE” display item.
➮ If you want to switch back to the
previous menu without changing
the colour, press the softkey 5 assigned to the “BREAK” display
item.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Configuring the spectrum
analyser
The spectrum analyser in your display
provides a symbolic representation of
the sound system’s output level. If the
spectrum analyser is switch on, it will
appear automatically after a short time
if you refrain from pressing a button
whilst an audio source is playing.
You can also choose to deactivate the
spectrum analyser.
Switching the spectrum analyser
on/off
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Repeatedly press the softkey 5
assigned to the “SPECTRUM” display item until the “SPECTRUM
OFF” or “SPECTRUM ON” setting
that you want is displayed in the
top display line.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
70
ADJUSTING THE
DISPLAY SETTINGS
RADIO MODE
Inverting the appearance of the
display content
You can invert the appearance of the
display content.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “DISPLA Y” display item.
➮ Press the softkey 5 assigned to
the “INVERT” display item.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
Radio mode
This device is equipped with an RDS
radio receiver. Many of the receivable
FM stations broadcast a signal that not
only carries the programme but also
additional information such as the station name and programme type (PTY).
The station name appears in the display as soon as the tuner receives it.
You can optionally display the programme type. For further details, please
read the section entitled “Programme
type (PTY)”.
Adjusting the tuner settings
To ensure that the tuner works properly, the device must be configured for the
region in which you are using it. Y ou can
choose between Europe and the USA.
By default, the tuner is set to the region
in which the device was sold. If you experience problems with radio reception,
please check this setting.
➮ Press the MENU button 9.
➮ Press the softkey 5 assigned to
the “TUNER” display item.
➮ Press the softkey 5 assigned to
the display item of the region that
you want: “AREA EUR” or “AREA
USA”.
➮ Press the joystick OK 8 or the
MENU button 9 to close the
menu.
The settings are saved.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
71
DANSK
Loading...