Blancett B220-880, B220-881, B220-882, B220-885 Specifications

K-Factor Scalers

B220-881

B220-885

B220-880

B220-882

Models B220-880, B220-881, B220-882 and B220-885

DESCRIPTION

The Blancett K-Factor Scaler converts a low level frequency output (such as that from a Blancett turbine flow meter) into a scaled square wave digital output signal. This adjustable frequency divider converts or scales the turbine meter output into units of measurement needed for a particular application and recognized by almost any data collection device. The k-factor scaler provides an amplified signal, even when a frequency conversion is not required. The signal is more immune to electrical noise and capable of transmission over longer distances than a raw turbine meter output.

FEATURES

• Scales turbine meter output to desired engineering units

• Switch-selectable or programmable versions available

• Converts frequency outputs into recognizable units for PLCs and other devices

• Amplifies turbine meter pulse output

• CSA approved

OPERATING PRINCIPLE

Fluid moving though a turbine flow meter causes the rotor to rotate in relation to the flow rate. The rotation of the rotor blades cuts through the magnetic field generated by the magnetic pick-up which in turn generates a frequency output signal that is directly proportional to the speed of the rotor.

The signal produced is received by the K-Factor Scaler input amplifier, which has an input sensitivity of 30 mV p-p to 30 V p-p. The signal is then sent to an onboard microcontroller, which acts as a divisor with a range of 1…999,999,999.

The divisor (K-factor) is user adjustable and set by programming it into the board. The microcontroller handles the dividing process by counting the input pulses and comparing it to the programmed K-factors. Once the count equals this value, an output pulse occurs for a selectable time period and the counting starts over.

The programmable version comes pre-calibrated from the factory when ordered with a Blancett Series 1100 turbine flow meter. In addition, it may be easily configured by the end-user through the use of a Windows®-based software utility kit (Model B220-900) that includes a PC serial port interface cable. See Figure 1.

From Turbine Flow Meter

MODELS

Badger Meter offers two versions of the K-Factor Scaler:

• Switch-selectable (Models B220-880, B220-881 or B220-882)

• Programmable (Model B220-885)

The switch-selectable version has a set of eight rotary switches within the enclosure. The rightmost switch represents the least significant digit of the k-factor number. For example, if the desired k-factor is 4572, the switches will be set to 00004572.

SGN-DS-00937-EN-01 (June 2017)

To Computer Serial Port

Figure 1: Programmable k-factor scaler and software

Models B220-880

B220-881

B220-882 K-Factor Storage Yes Yes No. of Digits 8 9 Range 1…99,999,999 1…999,999,999 K-Factor Entry Rotary switch Electronic input

B220-885

Product Data Sheet

K-Factor Scalers, Models B220-880, B220-881, B220-882 and B220-885

SPECIFICATIONS

External Power

Environmental

Inputs (Magnetic Pickup)

Output Signal

Pulse Output (using internal pullup resistor)

Pulse Output (using external pullup resistor)

Enclosure Ratings

Certifications

DIMENSIONS

Input voltage 8.5…30V DC (diode protected) Maximum current draw 18 mA (using internal resistor @ 30V DC input) Operating temperature –22…158° F (–30…70° C) Altitude 2000 m Use Indoor/outdoor Humidity 0…90% non-condensing Frequency range 0…4000 Hz Trigger sensitivity 30 mV p-p…30V p-p Max voltage 30V DC Max power 0.25 W Maximum current 8 mA VH = Power input voltage 0.7V DC VL = Less than 0.4V @ maximum input power Internal pullup resistor 3.6 kΩ (enabled/disabled by jumper) Maximum current 100 mA VH = Input voltage to external pullup resistor VL = [VH /(selected resistor value + 47 Ω)] × 47 Ω Pulse length 150 µs, 1 ms, 25 ms, 100 ms, 500 ms, 1 s, or auto mode

Model B220-885

Models B220-880, B220-881and B220-882

CSA Ordinary location CAN/CSA-C22.2 No. 61010-1-12, UL Std. No. 61010-1 (3rd Edition) Pollution Degree 2, Overvoltage Category I

3.65

(92.7)

2.78

Killark aluminum-capped elbow, Y3 CSA approved Class I, Div 1 & 2, Groups C, D; Class II, Div 1 & 2, Groups E, F, G; and Class III

Appleton GR conduit outlet boxes GRL100-A, GRLB100-A and GRT100-A, CSA approved Class I, Div 1, Groups B, C, D; Class II, Groups E, F, G; and Class III

4.72

(119.9)

3.88

(98.5)

DIA

(70.6)

DIA

3.00

(76.2)

4.72

(119.9)

1" NPT

(TYP)

3.65

(92.7)

1" NPT

(TYP)

Model B220-885 Model B220-880

4.72

(119.9)

3.88

(98.5)

DIA

3.93

(99.8)

1" NPT

(TYP)

(115.8)

3.75

(95.3)

DIA

4.56

1" NPT

(TYP)

2.88

(73.2)

5.37

(136.4)

Model B220-881 Model B220-882

Control. Manage. Optimize.

BLANCETT is a registered trademark of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding contractual obligation exists. © 2017 Badger Meter, Inc. All rights reserved.

www.badgermeter.com

Legacy Document Number: 02-SGN-BR-00015