Blancett B110-875, B110-500, B110-750, B111-110, B111-115 User Manual

...

Download

Page 1

Turbine Flow Meter

1100 Series Turbine Meter

TUR-UM-00014-EN-04 (October 2018)

User Manual

Page 2

Turbine Flow Meters, 1100 Series

CONTENTS

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Operating Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Pressure Drop in Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operational Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Turbine Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Turbine Replacement Kit Part Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turbine Assembly Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

New Turbine Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Part Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Page ii October 2018TUR-UM-00014-EN-04

Page 3

Introduction

INTRODUCTION

Designed to withstand the demands of the most rigorous flow measurement applications the Model 1100 turbine flow meter is reliable, rugged and cost effective. Originally developed for the secondary oil recovery market, the Model 1100 is an ideal meter for liquid flow measurement on or off the oil field.

The meter features a rugged 316 stainless steel housing and rotor support assemblies, CD4MCU stainless steel rotor, and abrasive-resistant tungsten carbide rotor, shaft, and journal bearings. The Model 1100 maintains measurement accuracy and mechanical integrity in the corrosive and abrasive fluids commonly found in oil field water flood project and many industrial applications.

OPERATING PRINCIPLE

Fluid entering the meter passes through the inlet flow straightener which reduces its turbulent flow pattern and improves the fluid’s velocity profile. Fluid then passes through the turbine, causing it to rotate at a speed proportional to the fluid velocity. As each turbine blade passes through the magnetic field, the blade generates an AC voltage pulse in the pickup coil at the base of the magnetic pickup (see Figure 1). These pulses produce an output frequency proportional to the volumetric flow through the meter. The output frequency represents flow rate and/or totalization of fluid passing through the turbine flow meter.

Magnetic Pickup

Other Frequency

Output Device

Turbine Rotor

Figure 1: Schematic illustration of electric signal generated by rotor movement

*Rotor and Rotor Shaft

*Upstream

Rotor Support

*Retaining Ring

*Thrust Ball

NOTE: *Indicates parts supplied in repair kits.

Figure 2: Typical cross-section of B110-375…B111-121 turbine flow meter

Output

Signal

Magnetic Pick-up

Conduit Adaptor

Meter Body

Retaining Ring

Groove

Retaining Pins

*Downstream Rotor Support

*Bearing

Page 3 October 2018 TUR-UM-00014-EN-04

Page 4

Specications

SPECIFICATIONS

Body 316 stainless steel

Rotor CD4MCU stainless steel

Materials of Construction

Operating Temperature –150…350° F (–101…177° C)

Pressure Rating* 800 or 5000 psi

End Connections NPT, BSP, Victaulic®, flange, hose barbed

Turndown Ratio 10:1

Accuracy

Repeatability ±0.1%

Calibration Water (NIST traceable calibration)

Pickup B111109

Certifications

* Consult factory for pressure ratings for anged meters. ** Consult factory for ordering options

Bearings —

Rotor Shaft Tungsten carbide

Rotor Support 316 stainless steel

±1% of reading for 7/8 in. and larger meters

±1% of reading over the upper 70% of the measuring range for 3/8, 1/2, and 3/4 in. meters

CSA Class I Div 1, Groups C & D Class II Div 1, Groups E, F & G: intrinsically safe**

CSA Clas I Div 1 Groups C,D; complies to UL 1203 and CSA 22.2 No. 30

Met Labs File No. E112860 (for explosion proof models only)

INSTALLATION

PRESSURE IN EXCESS OF ALLOWABLE RATING MAY CAUSE THE HOUSING TO BURST AND CAUSE SERIOUS PERSONAL INJURY.

AVERTISSEMENT

LA PRESSION AU-DESSUS DE L’ESTIMATION PERMISE PEUT FAIRE ÉCLATER ET CAUSER LE LOGEMENT LE DOMMAGE CORPOREL SÉRIEUX.

1. Check the internals of the ow meter for any foreign material. Make sure the turbine rotor spins freely prior to installation. Also, check uid lines and remove any debris found.

2. Install the ow meter with the ow arrow, etched on the exterior of the meter body, pointing in the direction of uid ow. Though the meter is designed to function in any position, where possible, install it horizontally with the conduit adapter facing upward.

3. Thread a magnetic pickup (Badger Meter model B111109 or equivalent) into the conduit adapter completely nger tight without forcing. Secure with a lock nut if supplied.

4. Install conduit or other ttings suitable for the installation area onto the conduit adapter hub on the ow meter.

Page 4 October 2018TUR-UM-00014-EN-04

Page 5

Installation

All Badger Meter Model 1100 turbine meters use stainless steel and tungsten carbide construction materials. Make sure the operating fluid is compatible with these materials. Incompatible fluids can cause deterioration of internal components and cause a reduction in meter accuracy.

The measured liquid should be free of any large particles that may inhibit rotation of the turbine blades. If particles are present, install a mesh strainer upstream before operating the flow meter. See Table 1 for strainer recommendations.

Part Number Strainer Mesh Clearance Filter Size

B110-375 60 0.0092 in. 260 μm

B110-500 60 0.0092 in. 260 μm

B110-750 60 0.0092 in. 260 μm

B110-875 60 0.0092 in. 260 μm

B111-110 60 0.0092 in. 260 μm

B111-115 20 0.0340 in. 0.86 mm

B111-120 10 0.0650 in. 1.6 mm

B111-121 20 0.0340 in. 0.86 mm

B111-130, B117-130 8 0.0900 in. 2.3 mm

B111-140, B117-140 10 0.0650 in. 1.6 mm

B111-160 4 0.1875 in. 4.8 mm

B111-180 8 0.0900 in. 2.3 mm

B111-200 4 0.1875 in. 4.8 mm

Table 1: Strainer mesh installation details

The preferred plumbing setup is one containing a bypass line (see Figure 3) that allows meter inspection and repair without interrupting flow. If a bypass line is not used, it is important that all control valves be located downstream of the flow meter (see Figure 4).

STRIKING AN EMPTY METER WITH HIGH VELOCITY FLOW STREAM CAN CAUSES DAMAGE.

ATTENTION

DES DOMMAGES PEUVENT ÊTRE PROVOQUÉS EN FRAPPANT UN MÈTRE VIDE AVEC UN JET D’ÉCOULEMENT DE VITESSE ÉLEVÉE.

This is true with any restriction in the flow line that may cause the liquid to flash. If necessary, install air eliminators to ensure that the meter is not incorrectly measuring entrained air or gas.

Badger Meter recommends installation of a minimum length, equal to ten (10) pipe diameters of straight pipe on the upstream side and five (5) diameters on the downstream side of the flow meter. Otherwise, meter accuracy may be affected. Piping should be the same size as the meter bore or threaded port size.

Severe pulsation and mechanical vibration affect accuracy and shorten the life of the meter. If this condition is present, consider using a flow meter possessing superior resistance to pulsation and vibration like the Badger Meter QuicSert. Do not locate the flow meter or connection cable close to electric motors, transformers, sparking devices, high voltage lines, or place connecting cable in conduit with wires furnishing power for such devices. These devices can induce false signals in the flow meter coil or cable, causing the meter to read inaccurately.

If problems arise with the flow meter, consult the Troubleshooting Guide on page 12. If further problems arise, consult the factory.

If damaged replace the internal components of the turbine flow meter with a turbine meter repair kit available from Badger Meter. For information pertaining to the repair kits, see Turbine Replacement on page 8.

Page 5 October 2018 TUR-UM-00014-EN-04

Page 6

Installation

Isolation Valve

Electronic

Flow Monitor

Isolation and

Flow Rate

Control Valve

Electronic

Flow Monitor

10 Pipe

Diameters

10 Pipe

Diameters

Turbine

Flow Meter

Bypass Valve

Figure 3: Meter installation with a bypass line

Turbine

Flow Meter

5 Pipe

Diameters

Figure 4: Meter installation without a bypass line

5 Pipe

Diameters

Control Valve

Page 6 October 2018TUR-UM-00014-EN-04

Page 7

PRESSURE DROP IN WATER

Pressure drop in water

Pressure Drop vs Flow Rate

3/4”

3/8”

3”

1/2”

3/4”

7/8”

1”

3/8”

1-1/2”

2”

6”

4”

10”

8”

0.1

Pressure Drop Bar

1/2”

1”

7/8”

1-1/2”

2”

4”

3”

8”

6”

10”

Pressure Drop PSID

0.01

0.1

0.5

(17)

(34)

(343)

100

(3429)

1000

(34,286)

8000

(274,236)

Flow Rate GPM (BPD)

0.005 1

(1.44)

(14.4)

Flow Rate LPM (m³/Day)

100

(144)

1000

(1440)

10,000

(14,400)

30,000

(57,600)

Figure 5: English units pressure drops Figure 6: Metric units pressure drops

OPERATIONAL STARTUP

Follow these steps when installing and starting the meter.

MAKE SURE TO SHUT OFF FLUID FLOW AND RELEASE PRESSURE IN THE LINE BEFORE ATTEMPTING TO INSTALL THE METER IN AN EXISTING SYSTEM.

AVERTISSEMENT

ASSUREZ-VOUS QUE LE FLUX DE FLUIDE A ÉTÉ COUPÉ ET DE LA PRESSION DANS LA LIGNE A ÉTÉ LIBÉRÉE AVANT D’ESSAYER D’INSTALLER LE MÈTRE DANS UN SYSTÈME ACTUEL.

After meter installation, close the isolation valves and open the bypass valve. Allow liquid to flow through the bypass valve for sufficient time to eliminate any air or gas in the flow line.

HIGH VELOCITY AIR OR GAS MAY DAMAGE THE INTERNAL COMPONENTS OF THE METER.

ATTENTION

DES DOMMAGES PEUVENT ÊTRE PROVOQUÉS EN FRAPPANT UN MÈTRE VIDE AVEC UN JET D’ÉCOULEMENT DE VITESSE ÉLEVÉE.

5. Open the upstream isolating valve slowly to eliminate hydraulic shock while charging the meter with the liquid. Open the valve to full open.

6. Open downstream isolating valve to permit meter to operate.

7. Close the bypass valve to a full closed position.

8. Adjust the downstream valve to provide the required ow rate through the meter.

OTE:N If necessary, use the downstream valve as a control valve.

Page 7 October 2018 TUR-UM-00014-EN-04

Page 8

Turbine replacement

TURBINE REPLACEMENT

The Model 1100 turbine flow meter uses wear resistant moving parts to provide trouble-free operation and long service life. The Designed for easy field service of a damaged flow meter Model 1100 repair kits replace only the internal parts, rather than replacing the entire flow meter. Repair parts use stainless steel alloys and tungsten carbide construction materials.

Each repair kit is factory calibrated to ensure accuracy throughout the entire flow range. Each kit is complete and includes a new K factor, which is the calibrated number of pulses generated by each gallon of liquid. Recalibration of the monitor or other electronics uses the K factor to provide accurate output data.

OTE:N If the meter repair kit part number ends in NCC (no calibration), it was not factory calibrated. For these repair kits, use

the nominal K factor.

Turbine Replacement Kit Part Number

Flow Meter Size

3/8 in. B110-375, B110-375-1/2 B251-102

1/2 in. B110-500, B110-500-1/2 B251-105

3/4 in. B110-750, B110-750-1/2 B251-108

7/8 in. B110-875 B251-109

1 in. B111-110 B251-112

1-1/2 in. B111-115 B251-116

2 in. Low B111-121 B251-116

2 in. B111-120 B251-120

3 in. B111-130 B251-131

4 in. B111-140 B251-141

6 in. B111-160 B251-161

8 in. B111-180 B251-181

10 in. B111-200 B251-200

Standard Magnetic Pick-up All Meter Sizes B111109

Turbine Assembly Removal

Replacement Kit Fits

Meter Part Number

Table 2: Repair kit part numbers

Repair Kit Part Number

HIGH-PRESSURE LEAKS ARE DANGEROUS AND MAY CAUSE PERSONAL INJURY. MAKE SURE TO SHUT OFF FLUID FLOW AND RELEASE RESIDUAL PRESSURE IN THE LINE BEFORE ATTEMPTING TO REMOVE THE METER.

AVERTISSEMENT

LES FUITES À HAUTE PRESSION SONT DANGEREUSES ET PEUVENT CAUSER LE DOMMAGE CORPOREL. ASSUREZ-VOUS QUE LE FLUX DE FLUIDE A ÉTÉ COUPÉ ET DE LA PRESSION DANS LA LIGNE A ÉTÉ LIBÉRÉE AVANT D’ESSAYER D’ENLEVER LE MÈTRE.

Page 8 October 2018TUR-UM-00014-EN-04

Page 9

Turbine replacement

Disassembly

1. Refer to Figure 7, Figure 8 and Figure 9 for relative positions of repair kit components.

2. Remove the magnetic pickup from the meter body to avoid damage during repair.

3. Remove the retaining ring from one end of the meter.

4. Remove the rotor support from the body. If the rotor support is jammed in the body, use a pair of pliers or vise-grips to break the rotor support free.

5. The rotor may also be removed at this time.

OTE:N 4 in. and larger meters have two retaining rings (one on either side of the rotor) that require removal before the rotor

can be removed (see Figure 9).

6. Remove the retaining ring from the opposite side of the meter.

7. Remove the second rotor support.

Magnetic

Pickup

Flow Direction

Arrow

Flow Direction

Upstream

Rotor Support

Retaining Ring

Upstream

Rotor Support

Retaining Ring

Rotor

Assembly

Retaining Ring

Groove

Flow Direction

Arrow

Flow Meter

Body

FLOW

Retaining Ring

Downstream

Rotor Support

Flow Direction

Arrow

Figure 7: Component positions for B110-375…B111-115 and B111-121

Magnetic

Pickup

Body

Retaining Ring

FLOW

Flow Direction

Arrow

Flow Direction

Arrow

Retaining Ring

Groove

Rotor

Assembly

Figure 8: Component positions for B111-120 and B111-130

Groove

Flow Direction

Arrow

Groove

Flow Direction

Arrow

Retaining RingFlow Meter

Retaining Ring

Downstream

Rotor Support

Flow Direction

Arrow

Upstream

Rotor Support

Flow Direction

Arrow

Retaining Ring

Grooves

Rotor

Assembly

Retaining Ring Retaining Ring

Magnetic

Pick-up

Flow Meter

Body

FLOW

Flow Direction

Arrow

Retaining Ring

Figure 9: Component positions for B111-140 and B111-200

Grooves

Downstream

Rotor Support

Flow Direction

Arrow

Retaining Ring

Page 9 October 2018 TUR-UM-00014-EN-04

Page 10

Turbine replacement

New Turbine Kit Installation

MPORTANTI

Before reassembly, note that an arrow is cast or engraved on each component. The arrow indicates the primary flow direction. When reassembled, the arrowheads must point in the direction of the fluid flow. The arrows must also be oriented in the up position on both rotor supports. The magnetic pickup side of the body signifies the up position. Performance of repair kit calibration is in the up position. Reinstallation of the repair kit in the up position ensures continuation of accurate measurements. Figure 7, Figure 8, and

Figure 9 show the proper alignment and orientation of the repair kits.

OTE:N Fractional size (3/8 in., 1/2 in. and 3/4 in.) rotors do not contain a cast or engraved arrow. However, a colored cap

on the downstream side of the rotor shaft indicates flow direction. Remove this cap before assembly, noting flow direction.

1. Install one of the rotor supports into the body bore, noting the orientation of the arrow.

2. Secure a retaining ring in the groove provided. Check for complete installation of retaining rings in each groove.

OTE:N 4 in. and larger meters have a retaining ring at both ends of the rotor (see Figure 9).

3. Insert the rotor and second rotor support in the opposite side of the body, noting the orientation of the arrow.

4. Secure the second retaining ring in the opposite groove, using the same procedure as in step 2 above.

EXCESS AIR PRESSURE MAY DAMAGE THE ROTOR AND BEARINGS BY OVER SPINNING.

ATTENTION

LA PRESSION ATMOSPHÉRIQUE EXCESSIVE PEUT ENDOMMAGER LE ROTOR ET LES ROULEMENTS PRÈS AU-DESSUS DE LA ROTATION.

5. Check the meter by lightly pung air through the assembly. If the rotor does not turn freely, disassemble the meter and remove anything that might obstruct movement of the rotor.

OTE:N At this time, electronics require recalibration. Refer to the display's user manual. If there are any questions on

recalibration, contact Badger Meter, Inc. or the manufacturer of the associated electronics.

6. Install the magnetic pickup.

Page 10 October 2018TUR-UM-00014-EN-04

Page 11

PART NUMBER INFORMATION

Part number information

Part

Number

B110-375-½

B110-500-½

B110-750-½

B110-375

B110-500

B110-750

B110-875

B111-110

B111-115

B111-121

B311-066

B111-120

B311-004

B111-130

B311-084

B111-140

B311-085

B111-160

B111-180

B111-200

Includes Standard Mag Pickup, p/n B111109, -150…330° F (-101…165° C), suitable for all mounting styles

Bore Size

3/8 in.

(9.5 mm)

1/2 in.

(12.7 mm)

3/4 in.

(19.1 mm)

3/8 in.

(9.5 mm)

1/2 in.

(12.7 mm)

3/4 in.

(19.1 mm)

7/8 in.

(22.2 mm)

1 in.

(25.4 mm)

1-1/2 in.

(38.1 mm)

1-1/2 in.

(38.1 mm)

1-1/2 in.

(38.1 mm)

2 in.

(50.8 mm)

3 in.

(76.2 mm)

3 in.

(76.2 mm)

4 in.

(101.6 mm)

4 in.

(101.6 mm)

6 in.

(152.4 mm)

6 in.

(152.4 mm)

8 in.

(203.2 mm)

10 in.

(254 mm)

End Connec-

tions

Max.

PSI

1/2 in. male NPT 5000

1 in. male NPT 5000

1-1/2 in. male

NPT

5000

2 in. male NPT 5000

2 in. grooved

end

5000

2 in. female NPT 5000

3 in. male NPT 800

3 in. grooved

end

800

4 in. male NPT 800

4 in. grooved

end

800

6 in. male NPT 800

6 in. grooved

end

8 in. grooved

end

10 in. grooved

end

800

gpm (lpm) bpd m3/d

0.6…3

(2.3…11.4)

0.75…7.5

(2.8…28.4)

2…15

(7.6…56.7)

0.6…3

(2.3…11.4)

0.75…7.5

(2.8…28.4)

2…15

(7.5…56.7)

3…30

(11.4…113.6)

5…50

(18.9…189.3)

15…180

(56.8…681.4)

15…180

(56.8…681.4)

15…180

(56.8…681.4)

40…400

(151.4…1514.2)

60…600

(227.1…2271.2)

60…600

(227.1…2271.2)

100…1200

(378.5…4542.5)

100…1200

(378.5…4542.5)

200…2500

(757.1…9463.5)

200…2500

(757.1…9463.5)

350…3500

(1324.9…13248.9)

500…5000

(1892.7…18927.1)

Flow Ranges

20…100 3.3…16 60 18000 1

25…250 4.1…41 60 13000 1

68…515 10.9…81.75 60 3300 1

20…100 3.3…16 60 18000 2

25…250 4.1…41 60 13000 2

68…515 10.9…81.75 60 3300 2

100…1000 16…160 60 3100 2

170…1700 27.25…272.5 40 870 2

515…6000 82…981 20 330 5

515…6000 82…981 20 330 6

1300…13000 218…2180 20 52 14

2100…21000 327…3270 10 57 15

3400…41000 545…6540 10 29 20

6800…86000 1090…13626 4 7 46

12000…120,000 1363…19076 4 3 56

17000…171,000 2725…27252 4 1.6 80

Strainer

Mesh

Approx. K-factor

Pulse/Gal

Meter

Weight

(lb)

End to End

Length

3.00 in.

(76.20 mm)

3.00 in.

(76.20 mm)

3.00 in.

(76.20 mm)

4.00 in.

(101.60 mm)

4.00 in.

(101.60 mm)

4.00 in.

(101.60 mm)

4.00 in.

(101.60 mm)

4.00 in.

(101.60 mm)

6.00 in.

(152.40 mm)

6.00 in.

(152.40 mm)

6.00 in.

(152.40 mm)

10.00 in.

(245.00 mm)

12.50 in.

(317.50 mm)

12.50 in.

(317.50 mm)

12.00 in.

(304.80 mm)

12.00 in.

(304.80 mm)

12.00 in.

(304.80 mm)

12.00 in.

(304.80 mm)

12.00 in.

(304.80 mm)

12.00 in.

(304.80 mm)

Page 11 October 2018 TUR-UM-00014-EN-04

Page 12

Turbine Flow Meters, 1100 Series

TROUBLESHOOTING GUIDE

Trouble Possible Cause Remedy

Meter indicates higher than actual flow rate

Cavitation. Debris on rotor support. Build up of foreign material on

Increase back pressure. Clean meter. Clean meter.

meter bore.

Meter indicates lower than actual flow rate.

Erratic system indication, meter alone works well (remote monitor application only).

Gas in liquid.

Debris on rotor. Worn bearing. Viscosity higher than calibrated.

Ground loop in shielding. Ground shield one place only. Look for

Install gas eliminator ahead of meter.

Clean meter and add filter. Clean meter and add filter. Recalibrate monitor.

internal electronic instrument ground. Reroute cables away from electrical noise.

Indicator shows flow when shut off. Mechanical vibration causes rotor to

Isolate meter.

oscillate without turning.

No flow indication. Full or partial open position.

Fluid shock, full flow into dry meter or impact caused bearing separation or broken rotor shaft.

Rebuild meter with repair kit and recalibrate monitor. Move to location where meter is full on startup or add downstream flow control valve.

Erratic indication at low flow, good indication at high flow.

Rotor has foreign material wrapped around it.

Clean meter and add filter.

No flow indication. Faulty pickup. Replace pickup.

System works perfect, except indicates lower flow over entire range.

Meter indicating high flow, upstream

By-pass flow, leak. Repair or replace bypass valves, or

faulty solenoid valves.

Fluid jet impingement on rotor. Change piping. piping at meter smaller than meter bore.

Meter indicating low flow, upstream piping at meter smaller than meter

Viscosity lower than calibrated. Change temperature, change fluid or

recalibrate meter.

bore.

Control. Manage. Optimize.

Blancett is a registered trademarks of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding contractual obligation exists. © 2018 Badger Meter, Inc. All rights reserved.

www.badgermeter.com