ASSEMBLY & INSTALLATION INSTRUCTIONS for: SER-08P-PC-_ _ / SER-08P-BL-_ _
CAUTION: READ ALL INSTRUCTIONS CAREFULLY FOR SAFE OPERATION AND INSTALLATION.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture in order to prevent possible
shock.
GENERAL
1. All electrical connections must be in accordance with local and national electrical code (N.E.C)
standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a
qualified electrician. Remove the fixture and the mounting package from the box and make sure
that no parts are missing by referencing the illustrations on the installation instruction.
2. Dimming controller type: TRIAC phase control dimmer.
3. Recommended TRIAC dimmers:
LUTRON: ARIADNI AYCL-153P, DIVA DVCL-153P, SKYLARK CTCL-153P, SKYLARK SCL-153P;
LEVITON: ILLUMATECH IPI06-1L, ILLUMATECH IPI10-1L, DECORA DSL06, DECORA DSM10;
LEGRAND: ADORNE: WHISPER/ ADWR, SOFTTAP/ ADTP, TOUCH/ ADTH.
ASSEMBLY AND INSTALLATION
1. Take the fixture out of box. Unpack bundled wire, but be careful not to bend or kink wires when
unpacking. Remove second package with 9 decorative candle seraphs (20).
2. Remove the back panel (10) from the fixture pan (11) by loosening three thumbscrews (12).
3. Place the back panel (10) over the outlet box (1). Insert mounting screws (9) through the slots in the
back panel and then tightly secure the mounting screws into the outlet box.
4. Pull the supply wires (2 & 8) and the house ground wire (5) out of the outlet box (1) and thread
through large center hole in back panel (10)
5. Temporarily suspend fixture pan (11) from back panel (10) by attaching loop (14) to mating hooks
(13).
6. Make the wiring connections: connect the white supply wire (2) to the white fixture wire (4);
connect the black supply wire (8) to the black fixture wire (7); connect the house ground wire (5) to the
fixture ground wire (6) using wire connectors (3).
7. Install a decorative candle seraph (20) into each candle holder. Unscrew nut (16) on top of outer
barrel (17). Loosen nut (16) and pull up outer barrel (17), then unscrew two side set screws (19)
by using the supplied allen wrench. Insert a candle seraph (20) into each lamp base (18), and tighten
the two set screws (19) to secure in place. Slide outer barrel (17) down over lamp base (18) and tighten
nut (16) on top to secure.
8. Determine the appropriate length of each suspension wire (if in doubt about exact length needed,
leave a little extra wire until final installation of fixture pan (11)). Push the excess wire up into the
canopy by pressing the small barrel of the gripper (15) upward. This will release the wire tension and
1. OUTLET BOX
2.WHITE SUPPLY WIRE
3.WIRE CONNECTORS
4.WHITE FIXTURE WIRE
5.HOUSE GROUND WIRE
6.FIXTURE GROUND WIRE
7.BLACK FIXTURE WIRE
8.BLACK SUPPLY WIRE
9.MOUNTING SCREWS
10.BACK PANEL
11.FIXTURE PAN
12.THUMBSCREWS
13.HOOK
14.LOOP
15.GRIPPER
16.NUT
17.OUTER BARREL
18.LAMP BASE
19.SET SCREWS
20.CANDLE SERAPH
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(10)
(12)
(11)
(9)
(13)
(14)
ALLEN
WRENCH
(15)
(16)
(17)
(18)
(19)
(20)
allow the suspended wire to be pulled through gripper (15). Roll excess wire into a small loop inside
the canopy. Wrap the supplied Velcro strap around this loop to keep the excess wire from falling
outside the fixture pan (11).
9. Make sure all wires are carefully placed inside fixture pan (11). Secure the fixture pan (11) to the
back panel (10) by tightening three thumbscrews (12).
10. Once the canopy is in place, fine tune the wire lengths longer or shorter to get each candle Seraph
adjusted to its preferred length by adjusting the gripper (15).
11. Once the length of each wire has been established, any remaining bends or kinks in the wire can be
straightened by bending out the kinks by hand while heating the cord up with the warm air from a hair
dryer or heat gun.
INSTALLATION IS NOW COMPLETED
BLACKJACK LIGHTING 1553 Barclay Blvd. Buffalo Grove, IL 60089 blackjacklighting.com Tel: 847-941-0588
BJL1609
Loading...