BLACKHAWK! BH6011, BH6010 User Manual

Long Chassis

Hydraulic Service Jacks

Operating Instructions & Parts Manual

Model Number BH6010 BH6011 (Air/Lever Actuated Model)

10939 N. Pomona Ave. Kansas City, MO 64153

sales@blackhawk-automotive.com

Capacity

10 Ton 10 Ton

816-891-6390

-Before using this product, read this manual and follow all its Safety Rules and Operating Instructions

Made in Taiwan

TABLE OF CONTENTS

Warranty P2 Save These Instructions P3 Product Description P3 Specifications & Safety Instructions P3 Assembly P4 Operation P5 Maintenance P5 Troubleshooting P6 Replacement Parts P6

ONE YEAR LIMITED WARRANTY

For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship, or which fails to conform to any implied warranty not excluded hereby.

Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153. Except where such limitations and exclusions are specifically prohibited by applicable law. (1) THE CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE (2) SFA COMPANIES SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHAT- SOEVER. (3) THE DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE (1) YEAR FROM DATE OF PURCHASE.

Some states do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SAVE THESE INSTRUCTIONS

For your safety, read, understand, and follow the information provided with and on this jack. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack, remove from service immediately.

Inspect before each use. Do not use if there are broken, bent, cracked, or damaged parts (including labels). Any jack that appears damaged in any way, operates abnormally or is missing parts, shall be removed from service immediately. If the jack has been or suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately discontinue to use until jack has been inspected by a Blackhawk authorized service center. It is recommended that an annual inspection be done by qualified personnel. Labels and Operator's Manual are available from manufacturer.

PRODUCT DESCRIPTION

Blackhawk Long Chassis Hydraulic Service Jacks are designed to lift, but not sustaining, up to rated capacity loads. They are designed to be used in conjunction with jack stands. Intended use: To lift one wheel or one axle of a vehicle for the purpose of service and/or repair of vehicle components. After lifting, loads must be immediately supported by appropriately rated jack stands. Check with vehicle owner's manual for proper lift points.The air actuated unit requires at least 7.8 CFM @ 90 - 175 PSI.

DO NOT USE TO DOLLY OR MOVE VEHICLE. DO NOT USE FOR ANY PURPOSE OTHER THAN THOSE USES OUTLINED ABOVE !

SPECIFICATIONS

Model Capacity Jack Size (L x W x H) Min. Height Max. Height

BH6010 10 Ton 54 3/4" x 20" x 12 3/4" 7" 27"

BH6011 (Air) 10 Ton 54 3/4" x 20" x 12 3/4" 7" 27"

SAFETY INSTRUCTIONS

BEFORE USE

1. Verify that the product and the application are compatible, if in doubt call Blackhawk Automotive Technical Service (816)891-6390.

2. Read the operator's manual completely and familiarize yourself thoroughly with the product, its components and recognize the potential hazards associated with its use before using this product.

3. Secure the handle into the handle sleeve by means of the bolt and lock washer provided. Tighten securely to prevent

accidental removal of handle while in use.

4. Locate and turn the handle knob counterclockwise to open the release valve (no more than 2 full turns).

5. With saddle fully lowered, locate and remove the oil filler plug. This will help release any pressurized air which may be trapped within the reservoir. Ensure the oil level is just below the oil filler plug hole.

6. Pump 6 to 8 full strokes. Ensure the oil level is within ~ 3/16" from the inner cylinder as viewed from the oil filler hole.

7. Ensure the jack rolls freely, that the pump and release valve operates smoothly, raises and lowers the unloaded saddle throughout the lift range before putting into service.

8. Replace worn or damaged parts and assemblies with Blackhawk Replacement Parts only. (See Replacement Parts Section). Lubricate as instructed in Maintenance Section.

9. Model BH6011 is fitted to accept the popular 1/4" PT air nipple. When installing 1/4" PT nipple of your choice, ensure that thread tape or compound is used when servicing connections. To help ensure trouble free operation, an inline air dryer and oiler is recommended.

+ 5 hidden pages