BLACKHAWK! AXIOM U-L RIFLE STOCK CAMO FINISH User Manual
Page 1
AXIOM Rifle Stock
Owner’s Manual
™
Installation Instructions
ATTENTION: Read and follow all instructions and warnings prior to installation and/or fir-
ing a Axiom equipped firearm. Take extra time to review the shooting tips & techniques
section of this manual (Page 7). If you are at all unsure of your abilityto install your Axiom
Rifle Stock safely, please seek the services of a competent gunsmith.
WARNING 1: Before beginning stock installation, make sure that the rifle is UNLOADED. Carefully check the chamber and magazine making both visual and touch verification.
WARNING 2: The Axiom Rifle Stock is not compatible with oversized trigger guards.
Use of the Axiom Rifle Stock with an oversized triggerguard will cause product failure and
possible injury. Note: Most factory installed trigger guards are compatible with the Axiom
Rifle Stock.
WARNING 3: The Axiom Rifle Stock is not compatible with trigger guard mounted
oversized safeties. Use of the Axiom Rifle Stock with an oversized safety will cause product failure and possible injury.
TOOLS REQUIRED:
• Large Flat Blade Screw Driver
• Hex Key / Allen Wrench Set
• Torque Wrench (Recommended)
• Extended “ball end” Allen Wrench (Included)
www.BLACKHAWK.com
BLACKHAWK!®NORFOLK, VA U.S.A. 1.800.694.5263
50107098 REV. 04.09
INSTALLATION STEPS:
1. Remove action bolt from receiver. Remove original stock. Refer to manufacturer’s in-
structionsfor the best method to remove stock. Normally the barreled action is held in position by two screws located on the bottom of the stock. Using caution not to damage
screws, use the appropriate size and type of tool to remove the two screws (Fig. 1A).
Note: At this point the trigger guard is disconnected from the stock. For BDL models remove bottom magazine floor plate along with magazine housing. (Fig. 1B on the following page) Remove barreled action from stock. To avoid damage, take caution when
removing barreled action from original stock.
Fig. 1A
www.BLACKHAWK.com
BLACKHAWK!®NORFOLK, VA U.S.A. 1.800.694.5263
Page 2
Page 3
Installation Instructions Continued
Fig. 1B
2. Prepare Axiom Rifle Stock for Installation by removing rear butt stock. To remove pull down on
lever assembly and slide off buttstock. (Fig. 2)
Installation Instructions Continued
4. Carefully insert receiver or barreled action into the forend. Carefully align recoil lug
and trigger with corresponding pockets or openings. Slowly lower barreled action into
forend until it is fully seated. (Fig. 4) Note: The barreled action should slide into position
with limited hand pressure and when in final position there should very minimal
movement.
Fig. 4
5. While holding the assembly from Step 4, reinstall the magazine housing into the corresponding pocket on the bottom of the receiver. (Fig. 5) Note: To avoid damage to the
hinged floor plate and trigger guard in the following steps, the magazine housing must be
correctly installed in the receiver. Verify that the magazine housing is properly installed.
Fig. 2
3. Installation of the Axiom Rifle Stock also requires the removal of the pistol grip portion of the
stock. The stock is attached to the forend with a preinstalled bolt and lock washer. To loosen bolt,
insert the provided 1/4” ball end allen wrench into the hole located on the bottom of the stock. Turn
wrench counter clockwise until stock is free from forend. (Fig. 3)
Fig. 3
www.BLACKHAWK.com
BLACKHAWK!®NORFOLK, VA U.S.A. 1.800.694.5263
Fig. 5
www.BLACKHAWK.com
BLACKHAWK!®NORFOLK, VA U.S.A. 1.800.694.5263
Loading...