Black & Decker WLB36B Instruction Manual

BRIGHT BAR

™

INSTRUCTION MANU

AL

Thank you for choosing Black & Decker!

Go to www

.BlackandDecker.com/NewOwner

to register your new product

Catalog Number WLB36B

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No, AND DATE CODE

AVAILABLE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE

CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A

SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS

VITAL TO BLACK & DECKER.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Cat. # WLB36B Form # 90521851
August 2007 Copyright © 2007 Black & Decker

Printed in China

WLB36B_ManualEN_080907.qxp 8/9/2007 10:16 AM Page 11

• AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in appliance with

finger on switch. Be sure switch is off when plugging in.

• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be

provided on the circuits or outlets to be used. Receptacles are available
having built in GFCI protection and may be used for this measure of safety.

• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or

attachment not recommended for use with this appliance could be
hazardous. Note: Refer to the accessory section of this manual for further
details.

• STAY ALERT. Watch what you are doing. Use common sense. Do not

operate tool when you are tired.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other

part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if
switch does not turn it on and off.

• DO NOT OPERATE portable electric tools near flammable liquids or in

gaseous or explosive atmospheres. Certain components in these tools
normally spark, and the sparks might ignite fumes.

• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only

extension cords intended for use outdoors and so marked.

• EXTENSION CORDS. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. The following table shows
the correct size to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The smaller the gage number,
the heavier the cord.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating product. Failure to follow

all instructions listed below may result in electric shock, fire and/or serious
injury.

• AVOID DANGEROUS ENVIRONMENTS Don’t use appliances in damp or wet

locations. Don’t use appliances in the rain.

• KEEP CHILDREN AWAY. All visitors should be kept at a distance from work

area.

• STORE IDLE APPLIANCES INDOORS. When not in use, appliances should be

stored indoors in dry, and high or locked-up place – out of reach of children.

• USE RIGHT APPLIANCE. Do not use the appliance for any job except that for

which it is intended.

• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be

caught in moving parts. Rubber gloves and substantial, non-skid footwear
are recommended when working outdoors. Wear protective hair covering to
contain long hair.

• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety

goggles or safety glasses with side shields, complying with applicable safety
standards and, when needed, a face shield. Also use face or dust mask if
operation is dusty. This applies to all persons in the work area. Also use a
hard hat, hearing protection, gloves, safety shoes and dust collection
systems when specified or required. Safety glasses or the like are available at
extra cost at your local dealer or Black & Decker Service Center.

• DON’T ABUSE CORD. Never carry appliance by cord or yank it to disconnect

from receptacle. Keep cord from heat, oil, and sharp edges.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• DISCONNECT APPLIANCES. Disconnect the appliance from the power

supply when not in use, before servicing, and when changing accessories
such as blades and the like.

1 2

WLB36B_ManualEN_080907.qxp 8/9/2007 10:16 AM Page 1

SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF INJURY:

• Follow these instructions and those published by the manufacturer of any
equipment you intend to use with this unit. Review cautionary markings on
these products.

INTRODUCTION

Thank you for purchasing the

WLB36B Black & Decker®Bright Bar

™

. Please
read this manual carefully before use to ensure optimum performance and
avoid damage to the unit.

FEA

TURES

• 36 LED Bright Bar™offers three lighting options: 9-LED focused beam,

27-LED area light or 36-LED combined area and focused lighting

• Corded or cordless operation

• Built-in rechargeable Ni-MH battery (with supplied 120 volt AC

Charging/Power Adapter)

• High impact, shatter-resistant ABS housing

• 360° Swivel Hanging Hook for hands-free use

• Rubber Base allows unit to sit on flat surfaces

OPERATING THE UNIT

Position the unit as desired. The ON/OFF Switch on the side of the unit has
four positions.

The bottom position is OFF.
The next position up turns the 9-LED focused beam lights on.
The next position up switches the focused beam off and turns the 27-LED area

light on.
The next position up turns all 36 LEDs on.

SAFETY GUIDELINES / DEFINITIONS

DANGER: Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety

precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could
result in serious injury and property damage. There are certain applications for
which tools and equipment are designed. Black & Decker strongly
recommends that this product NOT be modified and/or used for any
application other than for which it was designed. Read and understand all
warnings and operating instructions before using any tool or equipment.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

3 4

WLB36B_ManualEN_080907.qxp 8/9/2007 10:16 AM Page 3

CARE AND MAINTENANCE

Safe Battery Disposal

This unit contains a nickel metal hydride rechargeable battery,
which which must be must be disposed of properly when it will
no longer retain a charge. For information on recycling this
battery, call toll-free [phone].

WARNINGS: TO REDUCE THE RISK OF INJURY / EXPLOSION

• Do not dispose of product in fire as batteries inside this product may

explode or leak.

• Do not expose the unit containing a battery to fire or intense heat as it

may explode.

For assistance with your product, visit our website www.blackanddecker.com
for the location of the service center nearest you or call the BLACK & DECKER
help line at 1-800-544-6986.

Accessories

Recommended accessories for use with your tool are available from your local
dealer or authorized service center. If you need assistance regarding
accessories, please call: 1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this

tool could be hazardous.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool service. Whether you
need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer
to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or
visit www.blackanddecker.com

5 6

OPERATING THE UNIT CORDED

Insert the Adapter’s DC Connector of the AC/DC Charging/Power Adapter into
the 12 Volt DC Charging Port. Insert the plug end into a (powered) standard
North American 120 Volt 60Hz outlet. Operate the unit as outlined in the
previous section.

RECHARGING THE UNIT

Insert the Adapter’s DC Connector of the AC/DC Charging/
Power Adapter into the 12 Volt DC Charging Port. Insert the
plug end into a (powered) standard North American 120 Volt
60Hz outlet. The red Charging Indicator LED will light to indicate
the unit is charging.

Notes:

Do not charge for longer than 8 hours. Charge or power
This unit ONLY with the originally supplied Class 2 transformer.
Consult manufacturer for replacement.

USING THE HANGING HOOK

The 360° Swivel Hanging Hook allows you to position the Bright Bar™for
convenient, hands-free operation.

CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:

• When Hanging Hook is in use, do not shake light.

• When light is hung by the Hanging Hook, do not shake the light or object
that it is hanging from. Do not hang the light from any electrical wires or
anything that it is not secure.

• Only use the Hanging Hook for hanging the Bright Bar

™

. The Hanging Hook is
not intended to support additional weight. Do not attach or hang anything
additional to the light or risk of breakage may occur.

WLB36B_ManualEN_080907.qxp 8/9/2007 10:16 AM Page 5