Black & Decker VEC1045BD, VEC1046BD, VEC1047BD User Manual

VEHICLE POWER SYSTEM

POWER INVERTER

200/400/750 WATT

VEC1045BD / VEC1046BD / VEC1047BD

USER’S MANUAL

& WARRANTY INFORMATION

IIIIMMMMPPPPOOOORRRRTTTTAAAANNNNTTTTSSSSAAAAFFFFEEEETTTTYYYYIIIINNNNFFFFOOOORRRRMMMMAAAATTTTIIIIOOOONNNN,,,,SSSSAAAAVVVVEEEETTTTHHHHEEEESSSSEEEEIIIINNNNSSSSTTTTRRRRUUUUCCCCTTTTIIIIOOOONNNNSS

SS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.

www.vectormfg.com

4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312

Toll Free: [phone]

8

Fault Protection Code and Troubleshooting Guide

INVERTER POWER SWITCH TURNED ON

SPECIFICATIONS

Power Inverter Model VEC1045BD VEC1046BD VEC1047BD

Maximum Continuous Power: 200 watts 400 watts 750 watts
Surge Capacity: 400 watts 800 watts 1500 watts
Input Voltage: 12.8 volts
Output Voltage: Approx. 115 volt AC RMS 60 Hz
Low Voltage Alarm: 11 volts DC ± 0.3 volt DC
Low Voltage Shutdown: 10.5 volts DC ± 0.3 volt DC
Thermal Shutdown: Automatic
Wave Form: Modified Sine Wave (MSW)
Output Connection: North American Standard Receptacles
Input Fuses: Internal
Input Cables: Battery cable with ring connector
Additional Protection: Overload, over voltage, overheating

Trouble/Indication Possible Cause Suggested Remedy

No AC output — DC input is out of range Check battery voltage.
(red LED lit

Excessive load — Turn unit off. Reduce the load,
thermal shutdown wait for the inverter to cool

down, then turn the unit on
again.

No AC output — Fuse(s) open Check DC input — fuse(s) in
green LED not lit vehicle. Replace the fuse with

one of the same type and rating
if necessary.

Low battery alarm Low battery voltage Recharge battery. Remove
sounds continuously load from the inverter while

recharging battery.

Bad connection or wiring Tighten all DC connections.

Motorized power tool Excessive start-up load If appliance does not star t,
will not start appliance is drawing

excessive voltage and
will not work with inverter.

Motorized power tool Purely inductive load Make the load not purely
does not operate at inductive. Operate an
correct speed incandescent lamp at the

same time as motor.

Television/Radio Snow in picture, Keep inverter and antenna
interference “buzzing” sound distant from each other. Use

shielded antenna. Connect
antenna to amplifier.

VEC1045_46_47_BD_Manual 4/28/05 5:16 PM Page 8

iii

Important Cable Information

Substantial power loss and reduced battery operating time results from inverters installed with cables that
are not able to supply full power. Symptoms of low battery power can result from cables that are either
excessively long or an insufficient gauge. Marine installations are also subjected to vibration and stresses
that exceed those of other mobile installations. Therefore, the installer/operator should be especially
aware of the requirements to maintain secure, tight, water-resistant electrical connections and to provide
for strain relief for DC cables and appliance wiring. Cable insulation must be the appropriate type for
the environment.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

To ensure reliable service, your power inverter must be installed and used properly. Please read the
installation and operating instructions thoroughly prior to installation and use. Pay particular attention to
the WARNING and CAUTION statements in this manual. The CAUTION statements advise against
certain conditions and practices that may result in damage to your inverter. The WARNING statements
identify conditions or practices that may result in personal injury.

Read All Instructions Before Using This Power Inverter!

WARNINGS
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPLOSION OR INJURY:

• Do not connect to AC distribution wiring.

• Remove appliance plug from outlet strip or turn off inverter before working on the
appliance. Multiple outlet power strips with switches and circuit breakers only
interrupt power to the "hot" receptacle terminals. The "neutral" terminals remain
powered with respect to the "ground" terminals.

• NOT approved for ignition protected areas. Do not make any electrical connections
or disconnections in areas designated as IGNITION PROTECTED.

• This is not a toy — keep away from children.

• This equipment employs components that tend to produce arcs or sparks. DO NOT
install in compartments containing batteries or flammable materials.

• Use this unit in properly ventilated areas ONLY.

• Do not open — there are no user-ser viceable parts inside.

• Do not inser t foreign objects into the outlet.

• Do not expose the unit to water, rain or snow.

CAUTIONS

• Always inspect batter y supply connections and cables to ensure they are tight and
that cable insulation is not damaged.

• Do not use with positive ground electrical systems (the majority of modern
automobiles, RVs, trucks and boats are negative ground). Reverse polarity
connection will result in a blown fuse and may cause permanent damage to the
inverter and will void warranty.

• This inver ter will not operate high wattage appliances or equipment that produce
heat, such as hair dryers, microwave ovens and toasters.

• Grounding the Neutral will cause the inverter to shut down. Do not operate this
inverter if it is wet. Do not install in engine compartment — install in a well
ventilated area.

• This inver ter has not been not tested for use with medical devices.

• Do not attempt to install or operate this unit while operating a motor vehicle.

FOR USAGE ABOVE 100 WATTS:

• Use batter y clips ONLY.

• DO NOT use the DC accessory plug or the fuse will open.

VEC1045_46_47_BD_Manual 4/28/05 5:16 PM Page ii