Black & Decker OR07B, OR09B, OR11B User Manual
Oil Filled Radiator
(OR07B)
(OR09B)
(OR11B)
First Use Safety Recommendation
Please read through this booklet for safe and efficient use of the appliance.
We urge you to read the “Hints” section and also follow all detailed
instructions even if you are familiar with using this appliance.
Keep this guide handy for future reference.
OR07B / OR09B / OR11B
IMPORTANT SAFEGUARDS
While using electrical appliances, in order to reduce the risk of fire, electric shock,
and/or injury to persons, basic safety precautions should be followed, including the
following:
• Read all instructions carefully.
• To protect against electrical shock, do not immerse the appliance, cord set or
plug in water or other liquids.
• Close supervision is necessary when any appliance is used by or near children.
• Keep children & animals away from the appliance & cord set.
• Unplug from outlet when not in use. Unplug before cleaning, changing
accessories or approaching parts which move in use.
• Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions or has been damaged in any manner. Return appliance to an
authorized service facility for examination, repair or adjustment.
• Do not use outdoors.
• Do not position this appliance directly below a socket outlet.
• Do not allow children or any person unfamiliar with these instructions use this
appliance.
• Always leave sufficient space around the heater for ventilation.
• Do not let the power cord hang over the edge of tables or counters, or touch hot
surfaces.
• Always route the cord carefully so it does not create a tripping hazard.
• Do not place on or near a hot gas or electric burner, or in a heated oven.
• Do not use the appliance for anything other than the intended use.
• The use of accessory attachments not recommended by this appliance
manufacturer may cause hazards.
• Surfaces may be hot during use and during the cool down period
• Do not leave this appliance unattended in use.
• To avoid a circuit overload, do not operate another high wattage appliance on the
same circuit.
• If an extension cord is used, please ensure it is correctly wired and rated for use
with this appliance. If in doubt, consult a qualified electrician. The extension cord
should be arranged so that it will not drape over the counters or table tops where
it could be pulled by children or tripped over.
SAVE THESE INSTRUCTIONS
-2-
Part identification
1 Thermostat dial
2 Low power button
3 High power button
4 Handle
5 Heating Fins
6 Wheel support
7 Wheel clamp
8 Wheel
9 Washer
10 Cap nut
11 Wing nut
Denotes Do not cover
5
6
MIN
2
MAX
4
1
3
Wheel support (6) Wheel (8)
Cap nut (10) & washer (9) Wheel clamp (7)
-3-
Flat on
wheel
Flat in
support
Align flats & fit wheel
OR7B 1500W, OR9B 2000W, OR11B 2500W
Fit washer
Fit nut &
tighten
Place clamp
over radiator
Locate free end of support
Fit wing
nut (11)
Locate bend
in support…
…with wheels “out”
Finished
item
Features
• 3000W
• 3-Heat settings
• Wheels
How to use your Radiator
Caution: This product is intended for heating rooms. Do not use this appliance for any other purpose. For
indoor, domestic use only.
Assembly:
• Fit the wheels before using the appliance. Never use the appliance without the wheels fitted.
• Fit a wheel into a wheel support (6) making sure to align the flat portions of each item. Fit a washer over the
threaded portion of the wheel, then fit the nut & tighten it. Repeat for the other wheel then repeat the
process to assemble the other wheel support.
• Place the heater on the floor upside down. It is quite normal to hear the oil moving inside the radiator.
• Holding the bent end, insert the wheel clamp (7) between the last 2 heating fins. Place one assembled
wheel support over this, & fit the bent end of the clamp through the hole in the support.
• Slide the wheel support towards the bend in the wheel clamp, rotating the clamp as it moves until the free
end can be fitted through the other hole.
• Tighten the wing nut onto the free end of the clamp.
• Repeat this assembly process for the other wheel assembly.
Note: When fully assembled, the 2 sets of wheels should be facing away from each other (wheels out). Put
the heater into its normal upright position. Wait for at least three minutes before operating the appliance.
-4-
Loading...