Black & Decker NST2018 TYPE 8 Owner’s Manual
CORDLESS 18 VOLT TRIMMER/EDGER
INSTRUCTION MANUAL
Date Code
Catalog Number
NST2018
Thank you for choosing Black & Decker!
Go to www.BlackandDecker.com/NewOwner
to register your new product.
PLEASE READ BEFORE RETURNING THIS
PRODUCT FOR ANY REASON:
Ifyouhaveaquestionorexperiencea problemwithyourBlack&Deckerpurchase,goto
HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS
forinstantanswers24hoursaday.
Ifyoucan'tfindtheanswerordonothaveaccesstotheinternet,
call1-800-544-6986from8a.m.to5p.m.ESTNon.-- Fri.tospeakwithanagent.
Pleasehavethecatalognumberavailablewhenyoucall.
KEY INFORMATION YOU SHOULD KNOW:
Charge battery for 9 hours before attempting to use your trimmer/edger.
To operate the trimmer, the lock out button must be pulled back.
This is an automatic feed trimmer - Do not bump head against ground.
Use only 0.065 inch diameter line.
Install guard.
Phillips screwdriver required (not supplied) to install guard.
For trouble free feeding and best results, only use Black & Decker
replacement spools with single 0.065 inch line. Black & Decker replacement
spool model number AF-IO0.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACION, CENTROS DE SERVIClO Y POLIZA DE GARANTiA.
ADVERTENClA: LI_ASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO,
±WARNING: ImportantSafetyWarnings
and Instructions
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this toot reads and understands all safety
instructions and other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing others.
• Keep long hair and loose clothing away from openings and moving parts.
zk
WARNING: When using electric gardening appliances, basic safety
precautions should always be followed to reduce risk of fire, electric shock, and
personal injury, including the following.
z WARNING: Some dust created by this product contains chemicals
known to the State of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• compounds in fertilizers
• compounds in insecticides, herbicides and pesticides
• arsenic and chromium from chemically treated lumber
To reduce your exposure to these chemicals, wear approved safety equipment
such as dust masks that are specially designed to filter out microscopic particles.
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual.
The information it contains relates to protecting YOUR SAFETY and PREVENTING
PROBLEMS. The symbols below are used to help you recognize this information.
/E DANGER: Indicates an imminently hazardous situation which, if not avoided, wilt
result in death or serious injury.
z_ WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
z_ CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
GENERALSAFETYWARNINGSAND
INSTRUCTIONSFORALLTOOLS
• READ and understand all instructions.
• A BATTERY OPERATED UNIT with integral batteries or a separate battery pack must
be recharged only with the specified charger for the battery. A charger that may be
suitable for one type of battery may create a risk of fire when used with another battery.
• USE BATTERY OPERATED UNIT ONLY with specifically designated battery pack.
Use of any other batteries may create a risk of fire.
• AVOID accidental starting. Be sure switch is inthe locked or off position before
inserting battery pack. Carrying units with your finger on the switch or inserting the
battery pack into a unit with the switch on invites accidents.
• DO NOT use unit if switch does not turn it on or off. A unit that cannot be controlled with
the switch is dangerous and must be repaired.
• DISCONNECT battery pack from unit or place the switch in the locked or off position
before making any adjustments, changing accessories, or storing the unit. Such
preventative safety measures reduce the risk of starting the unit accidentally.
• ALWAYSWEAREYEPROTECTION- Wearsafetyglassesorgogglesatalltimes
whenthisunitisinuse.Safetyglassesareavailableatextracostatyourlocal
Black&DeckerServiceCenterorauthorizedservicefacility.Alwaysusefaceordust
maskifoperationisdusty.
• GUARD- Donotusethisunitwithoutguardattached.
• DRESSPROPERLY- Donotwearlooseclothingorjewelry.Theycanbecaughtin
movingparts.Rubberglovesandsubstantialrubbersoledfootweararerecommended
whenworkingoutdoors.Don'toperatetheunitwhenbarefootorwearingopensandals.
Wearlongpantstoprotectyourlegs.Wearprotectivehaircoveringtocontaintonghair.
• NYLONLINE- Keepface,handsandfeetclearofrotatingnylonlineatalltimes.
• THEROTATINGLINEPERFORMSACUTTINGFUNCTION- Usecarewhen
trimmingaroundscreensanddesirableplantings.
• KEEPCHILDRENAWAY- Atlvisitorsshouldbekeptatsafedistancefromworkarea.
• IMPORTANTWARNING- Whenbeingusedasanedger,stones,piecesofmetal
andotherobjectscanbethrownoutathighspeedbytheline.Theunitandguardare
designedtoreducethedanger.However,thefollowingspecialprecautionsshouldbe
taken:
/k
WARNING: Make sure that other persons and pets are at least 100 ft.
(30.5m) away.
WARNING: To reduce the risk of rebound (ricochet)injury, work
going away from any nearby solid object such as a wall, steps, large stone, tree,
etc. Use great care when working close to solid objects, and, where necessary,
do edging or trimming by hand.
• AVOID ACCIDENTALLY STARTING - Don't carry unit with finger on trigger.
• DO NOT FORCE THE APPLIANCE - It will do the job better and with tess likelihoodof
a risk of injury at the rate for which it was designed.
• USE THE RIGHT APPLIANCE - Do not use this unit for any job except that for which it
is intended.
• DON'T OVERREACH - Keep proper footing and balance at all times.
• DAMAGE TO APPLIANCE - If you strike or become entangled with a foreign object,
stop tool immediately, check for damage and have any damage repaired before further
operation isattempted. Do not operate with a broken hub or spool.
• AVOID DANGEROUS ENVIRONMENTAL CONDITIONS - Do not use electric units in
damp or wet locations. Don't use the unit in the rain.
• DO NOT OPERATE trimmer/edgers ingaseous or explosive atmospheres. Motors in
these units normally spark, and the sparks might ignitefumes.
• STORE IDLE APPLIANCES INDOORS - When not in use, units should be stored
indoors in a dry locked-up place out of reach of children.
• STAY ALERT- Watch what you are doing. Use common sense. Do not operate unit
when you are tired.
• MAINTAIN APPLIANCES WITH CARE - Keep cutting edge sharp and clean for best
performance and to reduce the risk of injury. Follow instructionsfor lubricating and
changing accessories. Inspect appliance cord periodically, and ifdamaged, have it
repaired by an authorized service facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean, and free from oit and grease.
• CHECK DAMAGED PARTS - Before further use of the unit, a guard or other part
that is damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other condition that may affect
its operation. A guard or other part that is damaged should be properly repaired or
replaced by an authorized service center unless otherwise indicated elsewhere in this
manual.
• KEEP GUARDS IN PLACE AND IN WORKING ORDER.
• KEEP HANDS AND FEET AWAY FROM CUTTING AREA.
SAVE THESE INSTRUCTIONS
/_ ADDITIONAL IMPORTANT SAFETY INSTRUCTIONS
• AVOID DANGEROUS ENVIRONMENT- Do not use or charge battery in damp or wet
locations.
• DO NOT USE OR CHARGE battery in rain.
• REMOVE BATTERY before servicing, cleaning or removing material from the trimmer.
Remove battery from your trimmer and carry by the front handle when not in use.
• EXERCISE CARE in handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may overheat
and cause burns.
• DO NOT OPEN OR MUTILATE the batteries. Released electrolyte iscorrosive and
may cause damage to the eyes or skin. It may be toxic if swallowed.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for Class
B digital device, pursuant to part 15 of the FOC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS.
The label on
V volts
Hz ............. hertz
min ........... minutes
- - -. ......... direct current
[] .............. Class II Construction
Z_ .............safety alert symbol
Battery cap information
Battery storage and carrying caps are provided for use whenever the battery is out of
the unit or charger. Remove cap before placing battery in charger or unit.
your tool may include the following symbols.
A................. amperes
W................ watts
'_ .............. alternating current
no ............... no load speed
............. earthing terminal
.../min ....... revolutions or
reciprocations per minute
Battery Cap
WARNING: Fire hazard. Do not store or carry battery so that
metal objects can contact exposed battery terminals. For example, do not
place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries can possibly cause fires
if the battery terminals inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like. The US Department of
TransportationHazardousMaterialRegulations(HMR)actuallyprohibit
transportingbatteriesincommerceoronairplanes(i.e.,packedinsuitcasesand
carry-onluggage)UNLESStheyareproperlyprotectedfromshortcircuits.So
whentransportingindividualbatteries,makesurethatthebatteryterminalsare
protectedandwellinsulatedfrommaterialsthatcouldcontactthemandcausea
shortcircuit.
±SAFETY WARNINGS AND
INSTRUCTIONS
Charging
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1)
battery charger, (2) battery pack, and (3) product using battery pack.
3. z_ CAUTION: To reduce the risk of injury, charge only Black & Decker Battery
Packs. Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a
risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord
when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round
jacketed extension cords should be used, and we recommend that they be listed
by Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord
must be suitable for outdoor use. Any cord marked for outdoor use can also be
used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the
cord is suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety, and to prevent loss of power and overheating. The smaller the gauge
number of the wire, the greater the capacity of the cable; that is, 16 gauge has
more capacity than 18 gauge. When using more than one extension to make up
the total length, be sure each extension contains at least the minimum wire size.
Chart for minimum wire size (AWG) of Extension Cords
Nameplate rating AMPS - 0 - 10.0
Total Extension Cord Length (ft) 0-25 26-50 51-100
(0-7,6m) (7,6-15,2m) (15,2-30,4m)
Wire Gauqe 18 16 16
9. Use only the supplied charger when charging your unit. The use of any other
charger could damage the battery pack or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the unit. There are no customer serviceable
parts inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate battery packs even if they are severely damaged or completely
worn out.
13. Do not incinerate the batteries. They can explode in a fire. A small leakage
of liquid from the battery cells may occur under extreme usage, charging or
temperature conditions. This does not indicate a failure. However, if the outer seat
is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of
101-150
(30,4-45,7m)
14
10minutesandseekimmediatemedicalattention.MEDICALNOTE:Theliquidis
a25-35%solutionofpotassiumhydroxide.
IMPORTANT CHARGING SAFETY
INSTRUCTIONS
Charging Procedure
THE BATTERY PACK IS NOT FULLY CHARGED AT THE
FACTORY. CHARGE BATTERY PACK FOR AT LEAST 9
HOURS BEFORE USE.
The charger is designed to use standard household 120 volt
60 Hz power.
1. Plug the charger into any standard 120 Volt 60 Hz electrical
outlet (figure A).
2. Slide the charger onto the battery pack as shown in figure B
and let the battery pack charge initially for 9 hours. After the
initial charge, under normal usage, your battery pack should
be fully charged in 6 to 9 hours.
2a) During charging the green LED wilt appear.
2b) When charging is complete the green LED will go off.
3. Unplug charger, and remove the battery pack. Place the
battery pack into the tool until it "clicks" into place.
NOTE: To remove the battery pack, press down on the
release button on the back of the battery pack and slide out
(figure C).
IMPORTANT CHARGING NOTES
1. After normal usage, your battery pack should be fully charged in 6 to 9 hours. If
the battery pack is run-down completely, it may take up to 9 hours to become fully
charged. Your battery pack was sent from the factory in an uncharged condition.
Before attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the battery pack in an air temperature below +40°F(+4.5°C), or
above +105°F (+40.5°C). This is important and will prevent serious damage to the
battery pack. Longest life and best performance can be obtained if battery pack is
charged when air temperature is about 75°F (24°C).
3. While charging, the charger may hum and become warm to touch. This is a
normal condition and does not indicate a problem.
4. If the battery pack does not charge property--(1) Check current at receptacle by
plugging in a tamp or other appliance. (2) Check to see if receptacle is connected
to a light switch which turns power off when you turn out the lights. (3) Move
charger and battery pack to a surrounding air temperature of 40°F (+4.5°C) to
105°F (+40.5°C). (4) If the receptacle and temperature are ok, and you do not get
proper charging, take or send the battery pack and charger to your local Black &
Decker service center. See Tools Electric in yellow pages.
5. The battery pack should be recharged when it fails to produce sufficient power on
jobs which were easily done previously. DO NOT CONTINUE using unit with its
battery pack in a depleted condition.
6. The battery pack wilt reach optimum performance after being cycled 5 times
during normal usage. There is no need to run the battery pack down completely
before recharging. Normal usage is the best method of discharging and recharging
the battery pack.
STORAGE RECOMMENDATION
1. Store tool:
a.) with the battery pack removed and on the charger.
b.) in a place that is coot and dry away from direct sunlight and excess heat or
cold.
c.) out of the reach of children.
2.Forprolongedstoragesuchasoverthewinter,thebatterypackshouldbefully
chargedandthenremovedfromthecharger.Itshouldbechargedagainjustprior
touse.
LEAVING THE BATTERY PACK IN THE CHARGER
It is OK to leave battery packs on charge for long periods of time. The charger has a
maintenance mode which gives the battery pack enough charge to stay "topped off".
If however, the tool is not expected to be needed for more than 30 days, unplug the
charger and store battery pack in a cool, dry location. NOTE: A battery pack wilt lose
its charge when kept off of the charger. If the battery pack has not been kept on
maintenance charge, it may need to be recharged before use. A battery pack may also
lose its charge if left in a charger that is not plugged into an appropriate AC source.
ASSEMBLY INSTRUCTIONS
Before assembling your Cordless String Trimmer, check that you have received the
following in the shipping carton. See figure 1.
A. Guard & screws
B. Charger
C. Nicad Battery Packs
D. Trimmer/Edger
E. Auxiliary Handle
ASSEMBLING AND
ATTACHING THE TWO PIECE
GUARD
WARNING: Remove battery
pack from tool before attempting to
attach the guard or make any adjustment.
NEVER OPERATE TOOL WITHOUT
GUARD FIRMLY IN PLACE. The guard
must always be on the tool to protect the
user.
TO ASSEMBLE:
• Remove the two guard sections from the
carton.
• Holding the sections as shown in figure 2,
insert the tab from the first guard section into
the slot of the second guard section. See
inset.
• Insert the side tab from the first guard section
into the slot of the second guard section until
you hear them "snap" together (figure 3).
• Insert the 3/4inch (19mm) Phillips screw
as shown in figure 4 to complete the guard
assembly (Phillips screwdriver not included).
TO ATTACH:
• Place the assembled guard over the
spool as shown in figure 5 and insert
the remaining three screws into the
guard as indicated by the arrows.
• Once the guard is installed, remove
the covering from the line cut-off blade,
located on the edge of the second guard
section.
Auxiliary handle attachment
Push the auxiliary handle onto the upper tube. Position the
handle so that the groove in the tube (a) is located in the
underside of the handle to match the rib (b) as shown in
figure 6.
Insert the handle bolt through the hole in the handle as
shown in figure 7.
Auxiliary handle adjustment
For maximum comfort and control, adjust the auxiliary
handle to suit your height (figure 8). Shorter users
adjust handle to a lower position (away from you) and
taller users, adjust handle to an upper position (towards
you). The handle should be adjusted so that your front
arm is straight as shown in figure 11.
Height adjustment
The overall height of the trimmer can be adjusted by loosening
the lock collar and rotating it opposite to the arrow shown in
figure 9. The tubes can then be extended shorter or longer.
When the desired height is achieved tighten the collar by
rotating in the direction shown in figure 9.
OPERATING INSTRUCTIONS
Z_ CAUTION: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safetyglasses. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
/_ CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like
objects which could become entangled in the rotating line or spool. Be particularly
careful to avoid any wire which might be bent outwardly into the path of the tool,
such as barbs at the base of a chain link fence.
Operate the Trimmer/Edger _i_ Lock-out
• To turn trimmer on, pull the lock out button, shown in
figure 10, back and, then squeeze the trigger switch.
To turn the toot off, release the trigger.
• Slowly swing trimmer side-to-side as shown in figure 11.
Trigger Switch
• Toconvertformaintenanceedging,turnoffthetool.Asshown
infigure12,holdthetrimmerwithonehandbytheauxiliary
handle,graspthecollarandpushindirectionofarrowand
rotatethetrimmerheaduntilitstops,(halfturn),releaseyour
hand,(rotateclockwisewhenviewedfromtheswitchend).
Thetootislockedintheedgerposition.
Rotatethewireedgeguideforwardanddownintoplace
beforeedging,asshowninfigure13.
• Tooperateasamaintenanceedger,positiontrimmerabove
sidewalkasshowninfigure14.Theedgeguidecanreston
theedgeofthesidewalktohelpprovideacleanand
consistentcut.
• Returntotrimmingpositionbyturningthetootoff,pushin
directionofarrowandrotatingthetrimmerheadcounter
clockwiseuntilitstops.Whenusingthetoolinthetrimmer
modeyoumaychoosetofoldthewireedgeguideupout
oftheway.
Line Feeding
Your trimmer uses .065 in. (1.65mm) diameter nylon line to
cut grass and weeds quickly and easily. In time, the tip of the
nylon line will become worn and the auto feed mechanism will
automatically feed and trim a fresh length of line.
The cutting line wilt wear faster if the cutting is done along sidewalks or other abrasive
surfaces or if heavier weeds are being cut. The automatic feed mechanism senses when
more cutting line is needed and feeds and trims the correct length of line whenever it
is required. No action is required to advance the line. Do not bump unit on ground in
attempt to feed line or for any other purpose.
Replacing Spool/Clearing Jams and Tangled Lines
From time to time, especially when cutting thick or stalky
weeds, the line feeding hub may become clogged with sap or _ ,/
other material and the line witt become jammed as a result.
To clear the jam, follow the steps listed below.
• Turn off the trimmer and remove the battery, lOO-
• Press the release tabs on the line spool cover, as shown in _._,,,z_/-., ....d
• Lift the spool of nylon line out of the hub and clear any broken
line or cutting debris from the spool area.
figure 15 and remove the cover by pulling it straight off. _/-
10
• Incaseofjamsandtangledlineunwrapabout
onefoot(30cm)oflinetoensurethatitis
undamaged.IfitisOKrewinditandinsertthe
lineendthroughtheeyeletinthespoolhub,as
showninfigure16.Pullthelinethroughthehole
tomaintaintensionwhileplacingthespooldown
intothehubwiththenotchedsideexposed,as
showninfigure17.
• PressthespooldownGENTLYandrotateituntil
youfeetitdropintoplace.(Wheninplace,the AF
spoolwillturnafewdegreesleftandrightfreely.)Spool
• Snapthespoolcoverbackon,insertthebattery
andturnthetooton.Inafewsecondsorless
you'llhearthenylonlinebeingcutautomatically
totheproperlength.
• Fortroublefreefeedingandbestresults,
onlyuseBlack&Deckerreplacement
spoolswithsingle0.065inchline.
Black&Deckerreplacementspoolmodel
numberAF-100.
Rewinding Spool from Bulk Line (use only .065 in. diameter line)
Bulk line is also available for purchase from your local retailer. NOTE: Hand wound
spools from bulk line are likely to become tangled more frequently than Black & Decker
factory wound spools.
To install bulk line, follow the steps below.
• Turn off the trimmer and remove the battery.
• Press the release tabs on the line spool cover, as shown in figure 15 and remove the
cover by pulling it straight off.
• Remove the spool from the toot and remove and
discard all line on the spool.
• Insert one end of the bulk line into the hole in the
spool shown in figure 18 about 1/2 in. (12mm).
• Hold the line in the hole and pull the rest of
the line through the slot in the spool, shown in
figure 18.
• Snugly and evenly wind the bulk line onto the
spool in the direction of the arrow on spool in
figure 18 until it is nearly full.
• Insert the line end through the eyelet in the spool
hub, as shown in figure 16. Pull the line through
the hole to maintain tension while placing the spool down into the hub with the notched side
exposed, as shown in figure 17.
• Press the spool down GENTLY and rotate it until you feet it drop into place. (When in
place, the spool will turn a few degrees left and right freely.)
• Snap the spool cover back on, insert the battery and turn the tool on. Ina few seconds or
less you'll hear the nylon line being cut automatically to the proper length.
MAINTENANCE
Cleaning
• Use only mild soap and damp cloth to clean the toot. Never let any liquid get inside the
toot; never immerse any part of the toot into a liquid.
/k
WARNING: Remove or disconnect battery before servicing, cleaning or
removing material from the gardening appliance.
11
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer
or authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
• Only use Black & Decker replacement spool No. AF-100.
• Reload nylon line (either bulk or prewrapped replacement spool) as shown inthis manual.
• Spool cap replacement part no. RC-100-P (See Figure 15).
• USE ONLY .065 in. (1.65mm) DIAMETER NYLON MONOFILAMENT LINE.
Heavier line will overload the motor, cause overheating and will impair the automatic feed.
This line is available at your local dealer or authorized service center.
• Do not use fishing line or other lines that are not recommended.
zL
WARNING: Theuseofanyaccessorynotrecommendedforuse withthis
toot could be hazardous.
Problem
•Line won'tfeed.
•Line failsto cutoff.
•Unitwill notstart.
•Battery willnotcharge.
•Battery willnot holda
charge.
TROUBLESHOOTING
Possible Cause
•Line tangledinspool.
•Line cutter inguard is
damaged or missing.
•Line extends past guard.
•Battery notinstalled properly.
•Battery notcharged.
•Battery notinsertedintocharger.
•Charger not plugged in.
•Surrounding airtemperature
too hotor too cold.
• Batterynot fullycharged.
Possible Solution
•Unwrap 24 inches of line
and rewind.
•Return to servicecenter
for repair.
•Rewind or trimlinetoline
cutter.
•Check battery
installation.
•Check battery charging
requirements.
•Insert batteryintocharger
untilgreen LED
appears.
•Plug charger into a
working outlet. Referto
"ImportantCharging Notes"
formore details.
•Check currentat
receptacleby plugging ina
lampor otherappliance.
•Check to see ifreceptacle
isconnected to alight
switchwhich turns power
offwhen you turn outthe
lights.
•Move charger andtool to
a surrounding air
temperature of above 40
degree F(4.5°0) or
below 105 degree F
(+40.5°C).
•Charge for9 hours before
use.
For assistance with your product, visit our website www.blaekanddeeker.eom for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
12
THE RBRC TM SEAL
The RBRC TM (Rechargeabte Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the
costs to recycle the battery (or battery pack) at the end of its useful life
have already been paid by Black & Decker. In some areas, it is illegal to
place spent nickel-cadmium batteries in the trash or municipal solid waste stream and
the RBRC program provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural resources by
returning the spent nickel-cadmium battery to an authorized Black & Decker service
center or to your local retailer for recycling. You may also contact your local recycling
center for information on where to drop off the spent battery, or call 1-800-544-6986
IMPORTANT
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service. Whether you need technical
advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow page directory under
"Tools--Electric" or call: 1-800-544-6986 or visit www.btackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects
in material or workmanship. The defective product will be replaced or repaired at no
charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns
should be made within the time period of the retailer's policy for exchanges (usually 30
to 90 days after the sate). Proof of purchase may be required. Please check with the
retailer for their specific return policy regarding returns that are beyond the time set for
exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned
or authorized Service Center for repair or replacement at our option. Proof of purchase
may be required.Black & Decker owned and authorized Service Centers are listed under
"Toots-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal
rights and you may have other rights which vary from state to state or province to
province. Should you have any questions, contact the manager of your nearest Black &
Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or
are missing, calt 1-800-544-6986 for a free replacement.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, check country specific warranty information contained in
the packaging, call the local company or see the website for warranty information.
Imported by
Black & Decker (U.S.)
Inc.,
701 E. Joppa Rd.
Towson, MD 21286
U.S.A.
13
See 'Tools-
Electric' [_
- Yellow Pages -
for Service &
Sales
MODE D'EMPLOI
COUPE-BORDURE SANS FIL DE 18 VOLTS
Code de date Numero de catalogue •
NST2018
Merci d'avoir choisi Black & Decker!
Consulter le site Web
www. Blac kandDecker• com/NewOwner
pour enregistrer votre nouveau produit.
A LIRE AVANT DE RETOURNER CE PRODUIT
POUR QUELQUE RAISON QUE CE SOIT :
SidesquestionsoudesproblemessurgissentapresI'achatd'unproduitBlack&Decker,
consulterlesiteWeb
HTTPJ/WWW.BLACKANDDECKER.COM/INSTANTANSWERS
pourobtenirdesreponsesinstantanement24heuresparjour.
SilareponseestintrouvableouenI'absenced'acces&Internet,composerle
1-800-544-6986de8 h&17h HNE,dulundiauvendredi,pourparleravecunagent.
Priered'avoirlenumerodecataloguesouslamainIorsdeI'appel.
RENSEIGNEMENTS IMPORTANTS
• Charger I'ensembte de piles pendant 9 heures avant d'utiliser le coupe-bordure.
• It faut pousser le bouton de verrouitlage vers I'arriere afin d'utitiser le coupe-bordure.
• L'alimentation du coupe-bordure est automatique; il ne faut pas en frapper la t6te
contre le sol.
• Utiliser seulement du fil de 1,65 mm (0,065 po) de diametre.
• Installer le protecteur.
• Tournevis b.pointe cruciforme requis (non fourni) pour installer un pare-main.
• Pour obtenir une alimentation du fil sans tracas et des resultats optimaux,
utiliser uniquement les bobines de rechange Black & Decker pourvues d'un fil
unique de 1,65 mm (0,065 po). Le numero de modele de la bobine de rechange
Black & Decker est AF-100.
14
Loading...