Black & Decker NST2018 TYPE 2 Owner’s Manual

INSTRUCTIONMANUAL

Date Code Catalog Number NST2018,

NST2018G, NST2018L

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

• AVOID ACCIDENTALLY STARTING - Don't carry unit with finger on trigger.

• DO NOT FORCE THE APPLIANCE - It will do the job better and with less likelihood of a risk
of injury at the rate for which it was designed.

• USE THE RIGHT APPLIANCE - Do not use this unit for any job except that for which it is
intended.

• DON'T OVERREACH - Keep proper footing and balance at all times.

• DAMAGE TO APPLIANCE - If you strike or become entangled with a foreign object, stop
tool immediately, check for damage and have any damage repaired before further operation

is attempted. Do not operate with a broken hub or spool.

• AVOID DANGEROUS ENVIRONMENTAL CONDITIONS - Do not use electric units in damp
or wet locations. Don't use the unit in the rain.

• DO NOT OPERATE trimmer/edgers in gaseous or explosive atmospheres. Motors in these
units normally spark, and the sparks might ignite fumes.

• STORE IDLE APPLIANCES INDOORS - When not in use, units should be stored indoors in
a dry locked-up place out of reach of children.

• STAY ALERT- Watch what you are doing. Use common sense. Do not operate unit when
you are tired.

• MAINTAIN APPLIANCES WITH CARE - Keep cutting edge sharp and clean for best
performance and to reduce the risk of injury. Follow instructions for lubricating and changing

accessories. Inspect appliance cord
periodically, and if damaged, have it repaired by an authorized service facility. Inspect
extension cords

periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.

• CHECK DAMAGED PARTS - Before further use of the unit, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform

its intended function. Check for alignment of moving parts, binding of moving parts, breakage
of parts, mounting, and any other condition that may affect its operation. A guard or other part

that is damaged should be properly repaired or replaced by an authorized service center
unless otherwise indicated elsewhere in this manual.

• KEEP GUARDS IN PLACE AND IN WORKING ORDER.

• KEEP HANDS AND FEET AWAY FROM CUTTING AREA,

• DO NOT CHARGE APPLIANCE IN RAIN OR IN WET LOCATIONS.

SAVE THESE INSTRUCTIONS

BEFOREYOU CALL, HAVETHE CATALOGNo.AND DATECODEAVAILABLE.IN MOST CASES,A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A

SUGGESTIONOR COMMENT, GIVE US A CALL.YOUR FEEDBACK IS VITALTO BLACK& DECKER.

KEY INFORMATION YOU SHOULD KNOW:

• Charge battery for 9 hours before attempting to use your trimmer/edger.

• To operate the trimmer, the lock out button must be pulled back.

• This is an automatic feed trimmer - Do not bump head against ground.

• Use only .065" diameter line.

• Install guard.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Cat No. NST2018, NST2018G, NST2018L Form No. 90509965 Rev. 1 Nov. '07
Copyright © 2007 Black & Decker Printed in China

/ WARNING: ImportantSafetyWarnings

and Instructions

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this tool reads and understands all safety
instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

• Keep long hair and loose clothing away from openings and moving parts.

zL

WARNING: When using electric gardening appliances, basic safety

precautions should always be followed to reduce risk of fire, electric shock, and personal
injury, including the following.

WARNING: Some dust created by this product contains chemicals known to

the State of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

To reduce your exposure to these chemicals, wear approved safety equipment such as dust
masks that are specially designed to filter out microscopic particles.

zL

WARNING: This product contains chemicals, including lead, known to the

State of California to cause cancer, and birth defects or other reproductive harm. Wash
hands after handling.

Z_ CAUTION: Wear appropriate personal hearing protection during use. Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.

• arsenic and chromium from chemically treated lumber

O

® ®

Charger not shown
Chargeur non illustre
Cargador no ilustrado

Lock-out O

O Verrouillage hors tension

Seguro f -

Trigger h
Interrupteur a.detente
Gatillo interruptor

O

0

z GENERALSAFETYWARNINGSAND

INSTRUCTIONSFORALLTOOLS

• READ and understand all instructions.

• A BATTERY OPERATED UNIT with integral batteries or a separate battery pack must be
recharged only with the specified charger for the battery. A charger that may be suitable for

one type of battery may create a risk of fire when used with another battery.

• USE BATTERY OPERATED UNIT ONLY with specifically designated battery pack. Use of
any other batteries may create a risk of fire.

• AVOID accidental starting. Be sure switch is in the locked or off position before inserting
battery pack. Carrying units with your finger on the switch or inserting the battery pack into a

unit with the switch on invites accidents.

• DO NOT use unit if switch does not turn it on or off. A unit that cannot be controlled with the
switch is dangerous and must be repaired.

• DISCONNECT battery pack from unit or place the switch in the locked or off position before
making any adjustments, changing accessories, or storing the unit. Such preventative safety

measures reduce the risk of starting the unit accidentally.

• ALWAYS WEAR EYE PROTECTION - Wear safety glasses or goggles at all times when
this unit is in use. Safety glasses are available at extra cost at your local Black & Decker
Service Center or authorized service facility. Always use face or dust mask if operation is

dusty.

• GUARD - Do not use this unit without guard attached.

• DRESS PROPERLY - Do not wear loose clothing or jewelry. They can be caught in moving
parts. Rubber gloves and substantial rubber soled footwear are recommended when

working outdoors. Don't operate the unit when barefoot or wearing open sandals. Wear long
pants to protect your legs. Wear protective hair covering to contain long hair.

• NYLON LINE - Keep face, hands and feet clear of rotating nylon line at all times.

• THE ROTATING LINE PERFORMS A CUTTING FUNCTION - Use care when trimming
around screens and desirable plantings.

• KEEP CHILDREN AWAY-All visitors should be kept at safe distance from work area.

• IMPORTANT WARNING - When being used as an edger, stones, pieces of metal and other
objects can be thrown out at high speed by the line. The unit and guard are designed to

reduce the danger. However, the following special precautions should be taken:

• Z_ WARNING: Make sure that other persons and pets are at least 100 ft. (30.5m) away.

• Z_ WARNING: To reduce the risk of rebound (ricochet) injury, work going away from any
nearby solid object such as a wall, steps, large stone, tree, etc. Use great care when working

close to solid objects, and, where necessary, do edging or trimming by hand.

/_ ADDITIONAL IMPORTANT SAFETY INSTRUCTIONS

• AVOID DANGEROUS ENVIRONMENT- Do not use or charge battery in damp or wet
locations.

• DO NOT USE OR CHARGE battery in rain.

• REMOVE BATTERY before servicing, cleaning or removing material from the trimmer.
Remove battery from your trimmer and carry by the front handle when not in use.

• EXERCISE CARE in handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may overheat and

cause burns.

• DO NOT OPEN OR MUTILATE the batteries. Released electrolyte is corrosive and may

cause damage to the eyes or skin. It may be toxic if swallowed.

FIRST AID MEASURES FOR GEL COMPONENTS (NST2018G ONLY)

If gel within the comfort grip becomes exposed and results in skin contact wash with soap

and water; for eye contact, flush with flowing water. If swallowed, seek medical attention.
Material Safety Data Sheet (MSDS) available from 1-800-544-6986

SAVE THESE INSTRUCTIONS.

The label on your tool may include the following symbols.

V .............. volts

Hz ............ hertz

min ............ minutes

.... .......... direct current

[] .............. Class II Construction

z_ ............ safety alert symbol

A ................ amperes

W................ watts

.............. alternating current

no .............. no load speed

............ earthing terminal

.../min ...... revolutions or

reciprocations per minute

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the battery is out of the
unit or charger. Remove cap before placing battery in charger or unit.

Battery Cap

WARNING: Do not store or carry battery so that metal objects can contact

exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes,
product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon
luggage) UNLESS they are properly protected from short circuits. So when transporting

individual batteries, make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit."

/ SAFETY WARNINGSAND INSTRUCTIONS

CHARGING THE BATTERY

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery
charger,(2) battery, and (3) product using battery.

3. _ CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs.
Other types batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by Black & Decker may result in a risk
of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round

jacketed extension cords should be used, and we recommend that they be listed by

Underwriters Laboratories (U.L). If the extension is to be used outside, the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is

suitable for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number
of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity

than 18 gauge. When using more than one extension to make up the total length, be
sure each extension contains at least the minimum wire size.

NAMEPLATE RATING AMPS - 0 - 10.0
Total Extension Cord Length (ft) 25 50 75 100 125 150

Wire Gauge 18 18 16 16 14 14

9. Use only the supplied charger when charging your unit. The use of any other charger
could

damage the battery or create a hazardous condition.

10. Do not attempt to open the charger or the unit. There are no customer serviceable parts
inside. Return to any authorized Black & Decker service center.

11. DO NOT incinerate battery packs even if they are severely damaged or completely worn
out.

12. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from
the battery cells may occur under extreme usage, charging or temperature conditions.

This does not indicate a failure. However, if the outer seal is broken and this leakage
gets on your skin:

a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of

10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a

25-35% solution of potassium hydroxide.

CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS

SAVE THESE INSTRUCTIONS

zLIMPORTANTCHARGINGSAFETY

INSTRUCTIONS

CHARGING THE POWER PACK

THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE
FACTORY, BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF

THE SAFETY INSTRUCTIONS,

The charger is designed to use standard household 120 volt 60 Hz power.

1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not
charge by means of an engine generator or DO power source, Use only 120V AC,

2. Slide the charger onto the power pack as shown in Figure 6 & 7 and let the power pack
charge initially for 9 hours. After the initial charge, under normal usage, your power pack

should be fully charged in 3 to 9 hours.

3. Unplug charger, and remove the power pack. Place the power pack in the unit and be
certain that it is inserted fully into the battery cavity until it "clicks" into place,

NOTE: To remove the power pack from the unit, press down on the release button on
the back of the pack (Figure 8) and slide out.

IMPORTANT CHARGING NOTES

1. After normal usage, your power pack should be fully charged in 3 to 9 hours. If the
power pack is run-down completely, it may take up to 9 hours to become fully charged.

Your power pack was sent from the factory in an uncharged condition. Before attempting
to use it, it must be charged for at least 9 hours.

2. DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above
+105°F (+40.5°C). This is important and will prevent serious damage to the power pack.

Longest life and best performance can be obtained if power pack is charged when air
temperature is about 75°F (24°C).

3. While charging, the charger may hum and become warm to touch. This is a normal con-
dition and does not indicate a problem.

4. If the power pack does not charge properly--(1) Check current at receptacle by plugging
in a lamp or other unit. (2) Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights. (3) Move charger and power pack to a sur-
rounding air temperature of 40°F (+4.5°C) to 105°F (+40.5°C). (4) If the receptacle and
temperature are OK, and you do not get proper charging, take or send the power pack

and charger to your local Black & Decker service center. See Tools Electric in yellow
pages.

5. The power pack should be recharged when it fails to produce sufficient power on jobs
which were easily done previously. DO NOT CONTINUE using unit with its power pack in

a depleted condition.

6. The power pack will reach optimum performance after being cycled 5 times during normal
usage. There is no need to run the batteries down completely before recharging. Normal

usage is the best method of discharging and recharging the power pack.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the red light glowing indefinitely.
The charger will keep the battery pack fresh and fully charged.

NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery
pack has not been kept on maintenance charge, it may need to be recharged before use. A
battery pack may also slowly lose its charge if left in a charger that is not plugged into an

appropriate AC source.

ASSEMBLY INSTRUCTIONS

Before assembling your Cordless String Trimmer, check that you have received the following in
the shipping carton. See Figure 1.
A. Guard. C. Nicad Battery Pack. E. Auxiliary Handle.

B. Charger. (NOT SHOWN) D. Trimmer/Edger.

ATTACHING THE GUARD

• z_ WARNING: NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE, THE

GUARD MUST ALWAYS BE ON THE TOOL TO PROTECT THE USER,

• Assemble the guard as shown in Figure 2, over the lug on the motor housing, then slide
guard forward to lock on the lug. Then with a phillips screw driver, screw the preassembled

screws in the guard into the motor housing. Figure 3.

AUXILIARY HANDLE ADJUSTMENT

• For maximum comfort and control, adjust the auxiliary handle to suit your height (Figure
4A). Shorter users adjust handle to a lower position (away from you) and taller users, adjust

handle to an upper position (towards you). The handle should be adjusted so that your front
arm is straight as shown in Figure 9.

HEIGHT ADJUSTMENT

• The overall height of the trimmer can be adjusted by loosening the lock collar and rotating it
opposite to the arrow shown in Figure 4B. The tubes can then be extended shorter or

longer. When the desired height is achieved tighten the collar by rotating in the direction
shown in Figure 4B.

OPERATING INSTRUCTIONS

• z_ CAUTION: ALWAYS WEAR EYE PROTECTION,

• Z_ CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which
could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which

might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence.

OPERATE THE TRIMMER/EDGER

• To turn trimmer on, pull the lock out button, shown in Figure 5, back and, then squeeze the
trigger switch. To turn the tool off, release the trigger.

• Slowly swing trimmer side-to-side as shown in Figure 9.

• To convert for maintenance edging, turn off the tool. (See Figure 10) Holding the trimmer with one
hand by the auxiliary handle, grasp the collar and push in direction of arrow and rotate the

trimmer head until it stops, (half turn), release your hand, (rotate clockwise when viewed from the
switch end). The tool is locked in the edger position.
Rotate the wire edge guide forward and down into place before edging, as shown in Figure 11.

• To operate as a maintenance edger, position trimmer above sidewalk as shown in Figure 12.

• Return to trimming position by turning the tool off, push in direction of arrow and rotating the
trimmer head counter clockwise until it stops. When using the tool in the trimmer mode you may

choose to fold the wire edge guide up out of the way.

LINE FEEDING

Your trimmer uses .065" (1.65mm) diameter nylon line to cut grass and weeds quickly and easily.

Intime, the tip of the nylon line will become worn and the auto feed mechanism will automatically
feed and trim a fresh length of line.
The cutting line will wear faster if the cutting is done along sidewalks or other abrasive surfaces or
heavier weeds are being cut. The automatic feed mechanism senses when more cutting line is

needed and feeds and trims the correct length of line whenever it is required. You don't even
have to think about it. Do not bump unit on ground in attempt to feed line or for any other purpose.

REPLACING SPOOL/CLEARING JAMS AND TANGLED LINES

From time to time, especially when cutting thick or stalky weeds, the line feeding hub may
become clogged with sap or other material and the line will become jammed as a result. To clear

the jam, follow the steps listed below.

• Turn off the trimmer and remove the battery.

• Press the release tabs on the line spool cover, as shown in Figure 13 and remove the cover by
pulling it straight off.

• Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool
area.

• In case of jams and tangled line unwrap about one foot (30cm) of line to ensure that it is
undamaged. If it is OK rewind it and insert the line end through the eyelet in the spool hub, as

shown in Figure 14. Pull the line through the hole to maintain tension while placing the spool
down into the hub with the notched side exposed, as shown in Figure 15.

• Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the
spool will turn a few degrees left and right freely.)

• Snap the spool cover back on, insert the battery and turn the tool on. In a few seconds or less
you'll hear the nylon line being cut automatically to the proper length.

REWINDING SPOOL FROM BULK LINE (USE ONLY .065" DIAMETER LINE)

Bulk line for your trimmer/edger is available at extra cost from your local dealer or
Black & Decker Service Center.

To install bulk line, follow the steps below.

• Turn off the trimmer and remove the battery.

• Press the release tabs on the line spool cover, as shown in Figure 13 and remove the cover by
pulling it straight off.

• Remove the spool from the tool and remove and discard all line on the spool.

• Insert one end of the bulk line into the hole in the spool shown in Figure 16 about 1/2" (12mm).

• Hold the line in the hole and pull the rest of the line through the slot in the spool, shown in
Figure 16.

• Snugly and evenly wind the bulk line onto the spool inthe direction of the arrow on spool in
Figure 16 until it is nearly full. (The spool holds 50 ft. (15.2m) of line and bulk line is sold in 50 foot

sections.)

• Insert the line end through the eyelet in the spool hub, as shown in Figure 14. Pull the line through
the hole to maintain tension while placing the spool down into the hub with the notched side
exposed, as shown in Figure 15.

• Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the
spool will turn a few degrees left and right freely.)

• Snap the spool cover back on, insert the battery and turn the tool on. In a few seconds or less
you'll hear the nylon line being cut automatically to the proper length.

Problem

• Line won't feed.

• Line fails to cut off.

• Unit will not start.

• Battery will not charge.

Possible Cause

• Line tangled in spool.

• Line cutter in guard is

damaged or missing.

• Line extends past guard.

• Battery not installed properly.

• Battery not charged.

•Battery not inserted into charger.

•Charger not plugged in.

• Surrounding air temperature

too hot or too cold.

For assistance with your product, visit our website www, blackanddecker, com for the location
of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.

TROUBLESHOOTING

Possible Solution

• Unwrap 24" of line and rewind.

• Return to service center for
repair.

• Rewind or trim line to line
cutter.

• Check battery installation.

• Check battery charging

requirements.

• Insert battery into charger

until red LED appears.

• Plug charger into a working

outlet. Refer to "Important
Charging Notes" for more details.

• Check current at receptacle

by plugging in a lamp or other
appliance.

• Check to see if receptacle is

connected to a light switch
which turns power off when

you turn out the lights.

• Move charger and tool to a

surrounding air temperature
of above 40 degree F(4,5°C) or
below 105 degree F (+40,5°C).

MAINTENANCE

CLEANING

• Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never

immerse any part of the tool into a liquid.

• z_ WARNING: Remove or disconnect battery before servicing, cleaning or removing material
from the gardening appliance.

ACCESSORIES

• Recommended accessories for use with your tool are available from your local dealer or
authorized service center.

Ifyou need assistance regarding accessories, please call: 1-800-544-6986.

• Use Black & Decker replacement spool No. AF-100.

• Reload nylon line (either bulk or prewrapped replacement spool) as shown in this manual.

• USE ONLY .065" (1.65mm) DIAMETER NYLON MONOFILAMENT LINE.
Heavier line will overload the motor, cause overheating and will impair the automatic feed. This

line is available at your local dealer or authorized service center.

• Do not use fishing line or other lines that are not recommended.

• Z_ WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.

THE RBRC TM SEAL /_'_

The RBRC TM (Rechargeable Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already
been paid by Black & Decker. In some areas, it is illegal to place spent

nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program
provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs
in the United States and Canada to facilitate the collection of spent nickel-cadmium batteries.

Help protect our environment and conserve natural resources by returning the spent nickel-
cadmium battery to an authorized Black & Decker service center or to your local retailer for
recycling. You may also contact your local recycling center for information on where to drop

off the spent battery, or call 1-800-544-6986

IMPORTANT

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should
be performed by authorized service centers or other qualified service organizations, always

using identical replacement parts.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or

genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools--Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of

two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom

it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the

sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be

required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state or province to province. Should you

have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Electric'

See 'Tools- I_

- Yellow Pages -
for Service &

Sales

GUIDED'UTILISATION

Code de date Numero de catalogue : NST2018,

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE

NST2018G, NST2018L

1-800-544-6986

AVANT D'APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART

DES CAS, UN REPRESENTANT DE BLACK & DECKER PEUT RESOUDRE LE PROBLEME PAR

TELEPHONE. Sl VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS

IMPRESSIONS SONT CRUClALES POUR BLACK & DECKER.

RENSEIGNEMENTS IMPORTANTS

• Charger I'ensemble de piles pendant 9 heures avant d'utiliser le coupe-bordure.

• II faut pousser le bouton de verrouillage vers I'arriere afin d'utiliser le
coupe-bordure.

• L'alimentation du coupe-bordure est automatique; il ne faut pas en frapper la t_te

contre le sol.

• Utiliser seulement du fil de 1,65 mm (0,065 pc) de diametre.

• Installer le protecteur.

C.ON.SERVER LE PRI:!:SENT GUIDE .&,TITRE DE
REFERENCE.

/ AVERTISSEMENT : Directives et consignes de

s_curit_ importantes.

AFIN DE REDUIRE LES RISQUES DE BLESSURES :

• Avant toute utilisation, s'assurer que tous ceux qui se servent de I'outil lisent et comprennent
toutes les mesures de securit6 et tout autre renseignement contenus dans le present guide.

• Conserver ces mesures et les relire frequemment avant d'utiliser I'outil ou d'en expliquer le
fonctionnement & d'autres personnes.

• #loigner les cheveux longs et les v_tements amples des ouvertures et des pieces en

mouvement.

z AVERTISSEMENT :Afin de reduire les risques d'incendie, de

secousses electriques ou de blessures Iorsqu'on utilise des outils electriques, il faut toujours
respecter les mesures de securit6 suivantes.

z AVERTISSEMENT :Le produit genere de la poussiere qui peut

renfermer des produits chimiques. Selon I'etat de la Califomie, ces produits chimiques peuvent
causer le cancer ainsi que des malformations congenitales, et ils presentent d'autres dangers

au systeme reproductif humain. Voici des exemples de tels produits
chimiques : • les composes d'engrais;

• les composes d'insecticides, d'herbicides et de pesticides;

Afin de minimiser les risques, porter de I'equipement de securit6 approuve comme des
masques antipoussieres specialement congu pour filtrer les particules microscopiques.

• I'arsenic et le chrome provenant de bois traite.

/ AVERTISSEMENT : Le produit renferme des produits chimiques, dont

du plomb. Selon I'etat de la Californie, ce produit chimique peut causer le cancer ainsi que des
malformations congenitales, et il presente d'autres dangers au systeme reproductif humain. Se

laver les mains apres I'utilisation.

z_ MISE EN GARDE : Porter un dispositif approprie de protection de I'oufe Iors de
I'utilisation du produit. Darts certaines conditions et durees d'utilisation, le produit peut
emettre un niveau de bruit provoquant la perte de I'oui'e.

LIRE ET COMPRENDRE TOUTES LES DIRECTIVES AVANT D'UTILISER L'OUTIL.

/ IMPORTANTES MESURES DE

SI CURITI POUR TOUS LES OUTILS

• LIRE et comprendre toutes les directives.

• UN OUTIL A PILES (& piles integrGes ou a_ensemble de piles amovible) dolt seulement _tre
charge au moyen du chargeur specifique a_I'outil. En effet, un chargeur congu pour un type de

pile peut presenter des risques d'incendie Iorsqu'utilise avec un autre type de piles.

• UTILISER L'OUTIL ,,_PILES UNIQUEMENT avec I'ensemble de piles specifique a_cet effet.

L'utilisation de tout autre type de piles presente un risque d'incendie.

• #VlTER les demarrages accidentels. S'assurer que I'outil est en position verrouille ou hors
tension avant d'y inserer I'ensemble de piles. Le fait de transporter I'outil avec les doigts sur

I'interrupteur ou le fait d'y inserer I'ensemble de piles Iorsque I'outil est sous tension presente

des risques.

• NE PAS utiliser un outil dont I'interrupteur est defectueux. Dans un tel cas, I'outil presente des

risques et il faut le faire reparer.

• DEBRANCHER I'ensemble de piles de I'outil ou mettre ce dernier hors tension ou en mode
verrouille avant de le regler, d'en remplacer des accessoires ou de le ranger. De telles

mesures de prevention reduisent les risques de demarrages accidentels de I'outil.

• TOUJOURS PORTER DES LUNETTES DE S#CURITE. Porter de lunettes de securit6 en tout
temps Iorsque I'outil est branche. Les lunettes de securit6 sont vendues separGment aux centres

de service Black & Decker ou aux ateliers d'entretien autorises. Toujours porter un masque

respiratoire si le travail genere de la poussiere.

• PROTECTEUR - Ne pas utiliser I'outil Iorsgue le protecteur n'est pas en place.

• PORTER DES V#TEMENTS APPROPRIES. Eviter de porter des v_tements amples et des

bijoux qui peuvent _tre happes par les pieces en mouvement. II est conseille de porter des gants

en caoutchouc et des chaussures robustes a_semelle en caoutchouc Iorsqu'on travaille a_

I'exterieur. Ne passe servir de I'outil pieds nus ou Iorsqu'on porte des sandales ouvertes. Porter

des pantalons pour se proteger les jambes. Proteger la chevelure si elle est Iongue.

• FIL DE NYLON - €:loigner en tout temps le visage, les mains et les pieds du fil en mouvement.

• LE FIL ROTATIF SERT A COUPER. Manipuler I'outil avec soin autour de moustiquaires et de

plantes a_conserver.

• ELOIGNER LES ENFANTS. S'assurer que tousles observateurs se trouvent a_une distance sQre
de la zone de coupe.

• AVERTISSEMENT IMPORTANT - Lorsque I'outil sert a_tailler le rebord des pelouses, le fil peut

projeter des pierres, des morceaux de metaux ou tout autre objet a_grande vitesse. L'outil et le
protecteur sont congus pour minimiser ce risque. II faut toutefois prendre les mesures de

p_recaution suivantes.

• ZL_AVERTISSEMENT : S'assurer que les observateurs et les animaux domestiques se trouvent

_plus de 30,5 m (100 pi) de la zone de coupe.

• .!lk AVERTISSEMENT : Afin de reduire les risques de blessures dues aux rebonds (ricochets),

manipuler I'outil en s'eloignant de tout objet comme un mur, des marches, une grosse roche ou un
arbre. Prendre garde Iorsqu'on coupe pres d'un tel objet et, le cas echeant, tailler la bordure a_la
main.

• #VlTER LES D#MARRAGES ACClDENTELS. Ne pas transporter I'outil avec le doigt sur

I'interrupteur.

• NE JAMAIS FORCER L'OUTIL Utiliser I'outil &son rendement nominal afin d'obtenir un meilleur

rendement a_moindre risque de blessures.

• UTILISER L'OUTIL APPROPRI#. Utiliser I'outil seulement aux fins pour lesquelles il a ete congu.

• NE PAS D#PASSER SA PORT#E Toujours demeurer dans une position stable et garder son
equilibre.

• OUTIL ENDOMMAGI_ - Lorsque I'outil frappe un corps etranger ou s'y coince, le mettre

imm{._diatement hors tension, en verifier I'etat et le faire reparer au besoin avant de le reutiliser. Ne
pas se servir de I'outil Iorsque la bobine ou le moyeu sont brises.

• EVITER LES CONDITIONS AMBIANTES DANGEREUSES, Ne passe servir d'outils electriques
dans des endroits humides ou mouilles. Ne passe servir de I'outil sous la pluie.

• NE PAS UTILISER des outils electriques portatifs dans des endroits renfermant des vapeurs

inflammables ou explosives. Les etincelles que produit le moteur en marche pourraient

enflammer ces produits.

• RANGER LES OUTILS INUTILIS#S ,&.L'INT#RIEUR dans un endroit sec, ferme a_cle, hors de la

portee des enfants.

• DEMEURER VIGILANT. Travailler avec vigilance et faire preuve de bon sens. Ne passe servir
de I'outil Iorsqu'on est fatigu&

• PRENDRE SOIN DES OUTILS. S'assurer que le rebord de coupe est propre et tranchant afin
d'optimiser le rendement et de minimiser les risques de blessures. Respecter les consignes

relatives & la lubrification et au remplacement des accessoires. Inspecter regulierement le cordon
de I'outil et le faire reparer au besoin & un atelier d'entretien autoris& Inspecter regulierement les
cordons de rallonge et les remplacer Iorsqu'ils sont endommages. S'assurer que les poignees

sont toujours propres, seches et libres de toute tache d'huile ou de graisse.

• V#RIFIER LES PI#CES ENDOMMAG#ES, Avant de continuer a_utiliser I'outil, il faut verifier si le
protecteur ou toute autre piece endommagee remplit bien la fonction pour laquelle il a ete prevu.

Verifier I'alignement et les attaches des pieces mobiles, le degre d'usure des pieces et leur

montage, ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de I'outil. Faire
reparer ou remplacer tout protecteur ou toute autre piece endommagee dans un centre de service

autorise, sauf indication contraire dans le present guide.

• S'ASSURER QUE LES PROTECTEURS SONT EN PLACE ET EN I_TAT DE

FONCTIONNEMENT,

• I_LOIGNER LES MAINS ET LES PIEDS DE LA ZONE DE COUPE,

• NE PAS CHARGER L'OUTIL SOUS LA PLUIE NI DANS DES ENDROITS MOUILLI_S.

CONSERVER CES MESURES.

IMPORTANTES MESURES DE SleCURITle ADDITIONNELLES

• I_VITER LES CONDITIONS AMBIANTES DANGEREUSES. Ne pas utiliser ni charger
I'ensemble de piles dans des endroits humides ou mouilles.

• NE PAS UTILISER NI CHARGER I'ensemble de piles sous la pluie ou dans un endroit
mouill&

• RETIRER L'ENSEMBLE DE PILES avant de faire I'entretien de I'outil, de le nettoyer ou d'en
retirer un materiau. Retirer I'ensemble de piles de I'outil et et transporter ce dernier par la

poignee avant Iorsqu'il ne sert pas.