Black & Decker NS118 TYPE 1, NS118 TYPE 3 Owner’s Manual

IHSTRUCTIOHMANUAL
Date Code Catalog Number NSl18,
NS118G, NS118L
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
USE ONLY as described in this manual. Use only manufacturer's recommended
attachments.
DO NOT put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and everything that may reduce air flow.
KEEP hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
DO NOT immerse any part of the unit in liquid.
DO NOT handle plug or unit with wet hands.
KEEP CHILDREN, BYSTANDERS AND ANIMALS AWAY from the work area a minimum of 30 feet (10 meters) when starting or operating the unit.
INSPECT THE AREA before using the unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage
during operation.
USE ONLY charger supplied by the manufacture to recharge.
EXERCISE CARE in handling batteries in order not to short the battery with conducting materials such as rings, bracelets and keys. The battery or conductor may overheat and
cause burns.
DO NOT OPEN OR MUTILATE the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the hedge trimmer. Receptacles are available having
built-in GFCt protection and may be used for this measure of safety.
CAUTION: EXPOSURE TO PETROLEUM BASED PRODUCTS.
'"WARNING: To reduce the risk of electrical shock; do not expose to rain,
do not use on wet surfaces. Store indoors.
FIRST AID MEASURES FOR GEL COMPONENTS (NS118G ONLY) If gel within the comfort grip becomes exposed and results in skin contact wash with soap
and water; for eye contact, flush with flowing water. If swallowed, seek medical attention.
Material Safety Data Sheet (MSDS) available from 1-800-544-6986
SAVE THESE INSTRUCTIONS.
1-800-544-6986
BEFOREYOU CALL,HAVETHECATALOGNo.ANDDATECODEAVAILABLE.INMOSTCASES,A
BLACK & DECKER REPRESENTATIVECAN RESOLVETHEPROBLEMOVERTHE PHONE.IFYOU HAVEA
SUGGESTIONOR COMMENT,GIVE USACALL YOUR FEEDBACKISVITALTOBLACK& DECKER.
KEY INFORMATION YOU SHOULD KNOW:
Before operating, make sure that the blower tube assembly is locked in place.
Charge battery for 9 hours before attempting to use your sweeper.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Cat. No. N8118, NS118G, NS118L Form No. 90509966-01 NOV. '07 Copyright © 2007 Black & Decker Printed in China
±WARNING: Important Safety Warnings
and Instructions
TO REDUCE RISK OF INJURY:
Before any use, be sure everyone using this unit reads and understands all safety instructions and other information contained in this manual.
Save these instructions and review frequently prior to use and in instructing others.
Do not point unit discharge at self or bystanders.
Keep long hair and loose clothing away from openings and moving parts.
zL
WARNING: When using an electric tool, basic safety precautions should
always be followed to reduce risk of fire, electric shock, and personal injury, including the following.
WAR N Some dust created by this product contains chemicals known to
the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
compounds in fertilizers
compounds in insecticides, herbicides and pesticides
To reduce your exposure to these chemicals, wear approved safety equipment such as dust ,_asks that are specially designed to filter out microscopic particles.
WARNING: This product contains chemicals, including lead, known to the
State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.
z GENERAL SAFETY WARNINGS AND
arsenic and chromium from chemically treated lumber
The label on your unit may include the following symbols•
V .............. volts
Hz ............ hertz
min ............ minutes
.... .......... direct current
[] .............. Class II Construction
............ safety alert symbol
A ................ amperes
W................ watts
"_ .............. altemating current
no .............. no load speed
G ............ earthing terminal
./min .......... revolutions or reciprocations per minute
O
0
BATTERY CAP INFORMATION Battery storage and carrying caps are provided for use whenever the battery is out of the
unit or charger. Remove cap before placing battery in charger or unit.
_ Battery Cap
INSTRUCTIONS FOR ALL TOOLS
READ and follow all instructions.
A BATTERY OPERATED UNIT with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
USE BATTERY OPERATED UNIT ONLY with specifically designated battery pack. Use of any other batteries may create a risk of fire.
AVOID accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying units with your finger on the switch or inserting the battery pack into
a unit with the switch on invites accidents.
DO NOT use unit if switch does not turn it on or off. A unit that cannot be controlled with the switch is dangerous and must be repaired.
DISCONNECT battery pack from unit or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the unit. Such
preventative safety measures reduce the risk of starting the unit accidentally.
ALWAYS WEAR EYE PROTECTION - Wear safety glasses or goggles at all times when this unit is in use. Also use face or dust mask. Safety glasses are available at extra cost at
your local Black & Decker Service Center or authorized service facility.
DO NOT place outlet of sweeper near eyes or ears when operating.
STORE IDLE UNITS. When not in use, the unit should be stored in a dry, high or locked-up place - out of reach of children.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN UNIT WITH CARE. Keep unit clean for best and safest performance. Follow instructions for proper maintenance.
DO NOT attempt to repair the sweeper. To assure product safety and reliability, repairs, maintenance, and adjustments should be performed by Black & Decker service centers or
authorized service centers, always using Black & Decker replacement parts.
DO NOT operate sweeper in a gaseous or explosive atmosphere. Motors in these units normally spark, and the sparks might ignite fumes.
AVOID DANGEROUS ENVIRONMENTAL CONDITIONS - Do not use electric units in damp or wet locations. Don't use the unit in the rain.
STAY ALERT - Watch what you are doing. Use common sense. Do not operate unit when you are tired.
USE THE RIGHT UNIT- Do not use this unit for any job except that for which it is intended.
USE EXTRA CARE when cleaning on stairs.
DO NOT allow to be used as a toy. Close attention is necessary when used by or near children. Not recommended for use by children.
DO NOT attempt to clear clogs from unit without first removing battery.
Ax
WAR ""NI "'N _,_: Do not store or carry battery so that metal objects can contact
exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery
cap. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually
prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit."
zLSAFETYWARNINGS AND INSTRUCTIONS
CHARGING THE BATTERY
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1) bat- tery charger, (2) battery, and (3) product using battery.
3. _ CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs. Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round
jacketed extension cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). tf the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor use can also be
used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the
cord is suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety, and to prevent loss of power and overheating. The smaller the gauge
number of the wire, the greater the capacity of the cable; that is, 16 gauge has more
capacity than 18 gauge. When using more than one extension to make up the total
length, be sure each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS
Total Extension Cord Length (ft) 25 50 75 100 125 150 Wire Gauge 18 18 16 16 14 14
9. Use only the supplied charger when charging your unit. The use of any other charger could damage the battery or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the unit. There are no customer serviceable
parts inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate battery packs even if they are severely damaged or completely worn out.
13. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature
conditions. This does not indicate a failure. However, if the outer seal is broken and this
leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of
10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a
25-35% solution of potassium hydroxide.
NAMEPLATE RATING AMPS - 0 - 10.0
SAVE THESE INSTRUCTIONS
z IMPORTANT CHARGING SAFETY
INSTRUCTIONS
CHARGING THE POWER PACK
THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE
FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF
THE SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
NOTE: Do not charge by means of an engine generator or DC power source, Use
only 120V AC,
2. Slide the charger onto the power pack as shown in Figure 2 & 3 and let the power pack charge initially for 9 hours. After the initial charge, under normal usage, your power
pack should be fully charged in 3 to 9 hours.
3. Unplug charger, and remove the power pack. Place the power pack in the unit and
be certain that it is inserted fully into the battery cavity until it "clicks" into place, NOTE: To remove the power pack from the unit, press down on the release button on
the back of the pack (Figure 4) and slide out.
IMPORTANT CHARGING NOTES
1. After normal usage, your power pack should be fully charged in 3 to 9 hours. If the
power pack is run-down completely, it may take up to 9 hours to become fully charged.
Your power pack was sent from the factory in an uncharged condition. Before
attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above
+105°F (+40.5°C). This is important and will prevent serious damage to the power pack. Longest life and best performance can be obtained if power pack is charged
when air temperature is about 75°F (24°C).
3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.
4. If the power pack does not charge properly--(1) Check current at receptacle by
plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F (+4.5°C) to 105°F (+40.5°C). (4) If
the receptacle and temperature are OK, and you do not get proper charging, take or send the power pack and charger to your local Black & Decker service center. See
Tools Electric in yellow pages.
5. The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using unit with its power pack
in a depleted condition.
6. The power pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the power pack.
LEAVING THE BATTERY PACK IN THE CHARGER The charger and battery pack can be left connected with the red light glowing indefinitely.
The charger will keep the battery pack fresh and fully charged. NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery
pack has not been kept on maintenance charge, it may need to be recharged before use. A battery pack may also slowly lose its charge if left in a charger that is not plugged into an appropriate AC source.
SWITCH
The switch can be operated by moving the lever from side to side. The "ON" and "OFF" positions are marked on the housing as shown in Figure 1A & 1B.
CAUTION: DONOTPOtNTUNtTDISCHARGEATSELFOR
BYSTANDERS.
Problem
Unit will not start.
Battery will not charge.
Possible Cause Possible Solution
Battery not installed properly.
Battery not charged.
Battery not inserted into charger.
Charger not plugged in.
Surrounding air temperature
too hot or too cold.
Check battery installation.
Check battery charging requirements.
Insert battery into charger until red LED appears.
Plug charger into a working
outlet. Refer to "Important
Charging Notes" for more
details.
Check current at receptacle by plugging in a lamp or other appliance.
Check to see if receptacle is
connected to a light switch which turns power off when
you turn out the lights.
Move charger and tool to a
surrounding air temperature of above 40 degree F(4,5°C)
or below 105 degree F
(+4o,5oc).
TROUBLESHOOTING
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
IMPORTANT
Toassure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or otherqualified service organizations,
always using identical replacement parts.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools--Electric" or
call: 1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges. The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory. This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province.
Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement. See 'Tools-
Black & Decker (U.S.) Inc., - Yellow Pages - Towson, MD 21286 U.S.A. Sales
Imported by Electric' I'_1
701 E. Joppa Rd. for Service &
GUIDED'UTILISATIOH
Code de date Num_ro de catalogue : NSl18,
NS118G, NS118L
OPERATION
r-_ ^_ UTION : Alwayswear safety glasses. Wear a filter mask if the operation
is dusty. Use of gloves, long pants and substantial footwear is recommended. Keep long hair and loose clothing away from openings and moving parts. THIS SWEEPER IS FOR
HOUSEHOLD USE ONLY. NOTE: Ensure the blower is switched off and the battery is removed before attaching or
removing the sweeper tube.
TUBE ASSEMBLY To attach the tube to the sweeper, line up the tube with the sweeper
housing as shown in Figure 5. Push the tube into the sweeper housing until the lock button engages the lock hole in the tube.
OPERATION
Hold the sweeper with one hand as shown in Figure 6 and sweep from side to side with
the nozzle several inches above the ground. Slowly advance keeping the accumulated pile of debris in front of you.
MAINTENANCE
CLEANING AND STORAGE
TURN OFF UNIT!
"_, ^_ UTION : Do NOT POUR OR SPRAY WATER ON THE UNIT.
Use only mild soap and a damp cloth to clean the unit. Never let any liquid get inside the unit; never immerse any part of the unit into a liquid. Your sweeper should be stored in a dry place. Do not store the unit on or
adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts.
THE RBRC TM SEAL
The RBRC TM (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already
been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC
program provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black & Decker service center
or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call 1-800-544-6986
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
1-800-544-6986
AVANT D'APPELER, AYEZ EN MAIN LE N ° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART
DES CAS, UN REPRESENTANT DE BLACK & DECKER PEUT RESOUDRE LE PROBLEME PAR
TELEPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS
IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.
RENSEIGNEMENTS IMPORTANTS
Avant de faire fonctionner I'outil, s'assurer que le tube de soufflage est verrouille
en place.
II faut charger la pile pendant 9 heures avant d'utiliser I'outil.
CONSERVER LE PRI SENT GUIDE h. TITRE DE
REFERENCE.
AVERTISSEMENT :Directives et consignes de
s6curit6 importantes.
AFIN DE RI_DUIRE LES RISQUES DE BLESSURES :
Avant toute utilisation, s'assurer que tous ceux qui se servent de I'outil lisent et comprennent toutes les mesures de securit6 et tout autre renseignement contenus dans le
present guide.
Conserver ces mesures et les relire frequemment avant d'utiliser I'outil ou d'en expliquer le fonctionnement & d'autres personnes.
Ne pas pointer I'orifice de sortie de I'outil vers sol ni vers d'autres personnes.
€:loigner les cheveux longs et les v6tements amples des ouvertures et des pieces en mouvement.
Loading...
+ 4 hidden pages