Black & Decker Mouse MS800, Mouse 90532198 User Manual

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.

1) Work area safety
a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust

. Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and

matching outlets will reduce risk of electric shock

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current

device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.

Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have
the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench

or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables bet-

ter control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.

The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing
power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be per­formed.

Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer.

A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
battery pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects that can make a
connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6) Service
a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a "live"

wire will make exposed metal parts of the tool "live" and shock the operator.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety

glasses. Also use face or dust mask if operation is dusty. ALWAYS WEAR CERTI­FIED SAFETY EQUIPMENT:

•

ANSI Z87.1 eye protection (CAN/CSA Z94.3)

•

ANSI S12.6 (S3.19) hearing protection

•

NIOSH/OSHA/MSHA respiratory protection

• Sanding of lead-based paint is not recommended. See Sanding Lead Based Paint for

additional information before sanding paint.

• Clean your tool out periodically.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below
are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation

which, if not avoided, may result in property damage.

Catalog Number MS800

KEY INFORMATION YOU SHOULD KNOW:

• Do not push down—let the sander do the work.

• Extended drywall sanding is not recommended for this product.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Catalog Number MS800 FORM NO. 90532198 REV. 1 SEPT. ‘08

Copyright © 2008 Black & Decker Printed in China

Hook and Loop

Pad

Tampon

Almohadilla

Sandpaper

Papier abrasif

Papel de lija

Pad Tip

Pointe de tampon

Punta de la almohadilla

Rotate 180°

Faire Tourner sur 180°

Gire180°

3

On Off Switch

Interrupteur

Interruptor de Encendido

Y Apagado

Extra Tips

Pointes supplémentaires

Puntas adicionales

4

1

2

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

MMOOUUSSEE®®DDEETTAAIILL SSAANNDDEERR PPOOLLIISSHHEERR

IINNSSTTRRUUCCTTIIOONN MMAANNUUAALL

Functional Description

A. Switch “ON”
B. Switch “OFF”
C. Dust Canister
D. Removable Pad Tip
E. Hook and Loop Sanding
Pad

A

B

D

C

E

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PPLLEEAASSEE RREEAADD BBEEFFOORREE RREETTUURRNNIINNGG TTHHIISS

PPRROODDUUCCTT FFOORR AANNYY RREEAASSOONN::

If you have a question or experience a problem with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

If you can’t find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.

Please have the catalog number available when you call.

for instant answers 24 hours a day.

Cleaning and Disposal

• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.

• Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. They should be placed in sealed refuse receptacles and disposed of
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.

• All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your
tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A
rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC
power. This information is printed on the nameplate. Lower voltage will cause loss of power
and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does
not operate, check the power supply.

Operating Instructions

WARNING: To reduce the risk of serious personal injury, read and follow all important

safety warnings and instructions prior to using this tool.

Switch

To turn the tool ON, hold it as shown in Figure 1 and push the portion of the switch marked
"I". To turn the tool OFF, push the portion of the switch marked "O".

Operation (Figure 1)

Grasp product as shown in figure 1 and turn it on. NOTE: Do not rest fingers on platen
during use. Move it in long sweeping strokes across the surface, letting it do the work. Light
pressure is all that is required for sanding, polishing or scrubbing. Excessive pressure will
slow the tool and produce inferior results. Check your work often, product is capable of
removing material rapidly.

WARNING: Shock hazard. Under no circumstances should this product be used near water.
CAUTION: To reduce the risk of injury, turn off and unplug the tool before making any

adjustments or removing or installing attachments or accessories.

Detail Sanding

Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces
and tight spots or corners.
The pad tips may wear unevenly, depending on use. The pads are designed to allow you to
interchange and /or rotate the diamond tip.

Fitting sanding sheets (Fig. 2)

• Detach the two diamond-shaped tips from the sanding sheet.

• Hold the tool with the sanding base facing upwards.

• Place the sanding sheet onto the sanding base.
The diamond-shaped tip can be reversed and replaced when worn.

• When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto
the sanding base again.

• When the whole tip is worn, remove it from the sanding base and fit a new tip.

Tip of the Sanding Base (Fig. 3)

When the sanding base tip is worn, it can be reversed or replaced.

• Reverse or replace the worn part.

Finger Attachment (Fig. 4)

The finger attachment is used for fine detail sanding.

• Remove the screw.

• Remove the diamond-shaped tip holder from the sanding base.

• Fit the finger attachment onto the sanding base.

• Fit and tighten the screw.

• Align the sanding sheet with the finger attachment.

Contour Holder Attachment (Fig. 5)

• The contour sanding pieces are for sanding curved surfaces and grooves.

• Remove the screw.

• Remove the diamond-shaped tip holder from the sanding base.

• Fit the contour holder onto the sanding base.

• Fit and tighten the screw.

Fitting and Removing a Contour Piece (Fig. 6 & 7)

• Choose the contour sanding piece profile most suitable for your application.

• Place one end of the contour sanding piece into the recess at the front end of the contour
holder.

• Push the other end of the contour sanding piece until it clicks into place.

• T

o remove the contour sanding piece, push it forward then pull the rear end out of

the contour holder (fig. 7).

Fitting a Sanding Sheet Onto a Contour Sanding Piece (Fig. 8)

• Align the sanding sheet with the contour sanding piece.

• Press the sanding sheet onto the contour sanding piece, making
sure that the sanding sheet follows the shape of the profile.

Dust Extraction (Fig. 9)
To Empty Dust Canister:

• The dust canister should be emptied after every 10 minutes of sanding.

• While holding the sander, grasp the dust collection canister and pull off of the sander.

• Remove the canister door and gently shake or tap the canister and door to empty.

• Re-attach the door and firmly push the canister back onto the sander.

CAUTION: Respiratory hazard. Never operate this tool for wood sanding unless the

dust canister is in place. Sanding dust exhaust may create a breathing hazard.

WARNING: Fire hazard. Collected sanding dust from sanding surface coatings
(polyurethane, linseed oil, etc.) can self-ignite in sander dust canister or elsewhere and cause
fire. To reduce risk, empty canister frequently and strictly follow sander manual and coating
manufacturer's instructions.

WARNING: Fire hazard. When working on metal surfaces, do not use the dust canister or
a vacuum cleaner because sparks are generated. Wear safety glasses and a dust mask. Due
to the danger of fire, do not use your sander to sand magnesium surfaces. Do not use for wet
sanding.

TROUBLESHOOTING

Pr

oblem

Possible

Cause

Possible

Solution

• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.

• Circuit fuse is blown. • Replace circuit fuse.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black & Decker
service center or authorized
servicer.)

• Circuit breaker is tripped. • Reset circuit breaker.
(If the product repeatedly
causes the circuit breaker to
trip, discontinue use
immediately and have it
serviced at a Black & Decker
service center or authorized
servicer.)

• Cord or switch is damaged. • Have cord or switch
replaced at Black & Decker
Service Center or Authorized
Servicer.

• Dust is not • Sandpaper holes do not align. • Use Mouse

®

sandpaper

being collected. with the appropriate hole

configuration.

For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Extension Cords

When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.

Symbols

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min ........................minutes ......................alternating current

......................direct current

n

o ........................no load speed

..........................

Class II Construction

........................

earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations per minute

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury.Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from face and
body.

Safety Warnings and Instructions: Sanders

• ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION.

• Clean your tool out periodically.

Other Important Safety Warnings and Instructions

Sanding

Lead Based Paint

Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,
we recommend the following precautions when sanding any paint:

Personal Safety

• No children or pregnant women should enter the work area where the paint sanding is
being done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing.

• NOTE: Only those dust masks suitable for working with lead paint dust and fumes should
be used. Ordinary painting masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.

• NO EATING, DRINKING or SMOKING should be done in the work area to prevent
ingesting contaminated paint particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work
area where dust would settle on them.

Environmental Safety

• Paint should be removed in such a manner as to minimize the amount of dust generated.

• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils
thickness.

• Sanding should be done in a manner to reduce tracking of paint dust outside the work
area.

9

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage
Than Than

0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

5

6

7

8

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.

Accessories

A variety of Mouse

®

accessories are available at extra cost. Listings per retailer may vary.
Note: Use only sandpaper with holes in the same configuration as on the base of the sander.
Sandpaper without holes will not allow dust to enter the canister.
The hook and loop pad and individual bases are replaceable parts. If they become worn,
contact your local service center. For more information call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

Application / Accessory Matrix

ACCESSOR

Y RECOMMENDED APPLICATIONS / USES

MEDIUM GRIT SANDPAPER PAINT, VARNISH, RUST REMOVAL
FINE GRIT SANDPAPER SURFACE BLENDING AND FINISHING
EXTRA FINE GRIT SANDPAPER SANDING BETWEEN COATS OF PAINT OR VARNISH
DETAIL SANDING TIPS CORNERS / HARD TO REACH PLACES
1 OT POLISHING / STRIPPING WOOL POLISHING METALS / STRIPPING VARNISH OR URETHANE
4 OT FINE POLISHING WOOL FINE POLISHING, SATIN FINISH ON PAINT / VARNISH / URETHANE

GREY FOAM PAD APPLYING AND REMOVING POLISH
WHITE NON

-WOVEN PAD LIGHT SCRUBBING

RED NON-WOVEN PAD HEAVY SCRUBBING / RUST REMOVAL

The pads described above may be available in kits where Mouse®products are sold. For
more information call 1-800-544-6986.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under "Tools—Electric"
or call: 1-800-544-6986.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should be
made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after
the sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required.Black & Decker owned and authorized Service Centers are listed under "Tools­Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or province to province. Should
you have any questions, contact the manager of your nearest Black & Decker Service
Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.

Avertissements de sécurité généraux pour les outils
électriques

AVERTISSEMENT! Lire tous les avertissements de sécurité et toutes les

directives. Le non-respect des avertissements et des directives pourrait se solder

par un choc électrique, un incendie et/ou une blessure grave.

Conserver tous les avertissements et toutes les directives pour un usage
ultérieur.

Le terme «outil électrique» cité dans les avertissements se rapporte à votre outil
électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail
a) Tenir la zone de travail propre et bien éclairée.

Les endroits sombres sont souvent

des causes d'accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, soit en

présence de liquides inflammables, de gaz ou de poussière.

Les outils
électriques produisent des étincelles qui peuvent enflammer la poussière ou les
vapeurs.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

c) Éloigner les enfants et les curieux au moment d’utiliser un outil électrique.

Une

distraction pourrait vous en faire perdre la maîtrise.

2) Sécurité en matière d’électricité
a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais

modifier la fiche en aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un
outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de
fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des

tuyaux, des radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc

électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à d'autres conditions où il

pourrait être mouillé.

La pénétration de l’eau dans un outil électrique augmente le

risque de choc électrique.

d) Ne pas utiliser abusivement le cordon d’alimentation. Ne jamais utiliser le

cordon pour transporter, tirer ou débrancher un outil électrique. Tenir le cordon
éloigné de la chaleur, de l’huile, des bords tranchants ou des pièces mobiles.

Les

cordons endommagés ou emmêlés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à une telle utilisation.

L’utilisation d’une rallonge conçue pour l’extérieur

réduit les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, utiliser une source d’alimentation dotée d’un disjoncteur de fuite à la
terre.

L’utilisation de ce type de disjoncteur réduit les risques de choc électrique.

3) Sécurité personnelle
a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un

outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou
sous l’influence de drogues, d’alcool ou de médicaments.

Un simple moment
d’inattention en utilisant un outil électrique peut entraîner des blessures corporelles
graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une

protection oculaire.

L’utilisation d’équipements de protection comme un masque
antipoussière, des chaussures antidérapantes, un casque de sécurité ou des
protecteurs auditifs lorsque la situation le requiert réduira les risques de blessures
corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à

la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou
d’insérer un bloc-piles, de ramasser ou de transporter l’outil.

Transporter un outil
électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique
dont l’interrupteur est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé standard avant de démarrer l’outil.

Une clé

standard ou une clé de réglage attachée à une partie pivotante peut causer des blessures.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps.

Cela permet

de mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de

bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces
mobiles.

Les vêtements amples, les bijoux ou les cheveux longs risquent de rester

coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de

dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés et
utilisés.

L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers

engendrés par les poussières.

4) Utilisation et entretien d’un outil électrique
a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à

l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus

sûre et à la vitesse pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux.

Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche du secteur ou le bloc-piles de l’outil électrique avant de faire

tout réglage ou changement d’accessoire, ou avant de ranger l’outil
électrique.

Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants, et ne permettre à

aucune personne n’étant pas familière avec un outil électrique (ou son manuel
d’instruction) d’utiliser ce dernier

. Les outils électriques deviennent dangereux entre

les mains d’utilisateurs inexpérimentés.

e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer

qu’elles sont bien alignées et tournent librement, qu’elles sont en bon état et ne
sont affectées par aucun trouble susceptible de nuire au bon
fonctionnement de l’outil électrique

.

En cas de dommage, faire réparer l’outil

électrique avant toute nouvelle utilisation.

Beaucoup d’accidents sont causés par

des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres.

Les outils de coupe
bien entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles
à contrôler.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à
effectuer.

L’utilisation d’un outil électrique pour toute opération autre que celle pour

laquelle il a été conçu est dangereuse.

5) Utilisation et entretien du bloc-piles
a) Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant.

L’utilisation
d’un chargeur qui convient à un type de bloc-piles risque de provoquer un incendie s’il
est utilisé avec un autre type de bloc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet effet.

L’utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets métalliques,

notamment des trombones, de la monnaie, des clés, des clous, des vis, etc., qui
peuvent établir une connexion entre les deux bornes.

Le court-circuit des bornes du

bloc-piles risque de provoquer des étincelles, des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors du bloc-piles, éviter tout

contact. Si un contact accidentel se produit, laver à grande eau. Si le liquide entre
en contact avec les yeux, obtenir des soins médicaux.

Le liquide qui gicle hors du

bloc-piles peut provoquer des irritations ou des brûlures.

6) Réparation
a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que

des pièces de rechange identiques

. Cela permettra de maintenir une utilisation

sécuritaire de l’outil électrique.

Consignes de sécurité particulières

• Saisir l’outil électrique par ses surfaces de prises isolées lorsque l’outil peut entrer en

contact avec des fils cachés ou son cordon. En cas de contact avec un fil sous tension,

les pièces métalliques de l’outil seront sous tension et l’utilisateur subira des secousses
électriques.

• Toujours porter des lunettes de protection et un appareil respiratoire antipoussière

pendant le ponçage.

AVERTISSEMENT : TOUJOURS porter des lunettes de sécurité. Les lunettes de vue

ne constituent PAS des lunettes de sécurité. Utiliser également un masque facial
ou anti-poussière si l’opération de découpe génère de la poussière.
TOUJOURS PORTER UN ÉQUIPEMENT DE PROTECTION HOMOLOGUÉ :

• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3);

• protection auditive ANSI S12.6 (S3.19);

• protection des voies respiratoires conformes aux normes NIOSH/OSHA/MSHA.

• Le ponçage de peintures à base de plomb n’est pas recommandé. Se reporter à la

section Mesures de précaution concernant le ponçage de peinture Précautions à
prendre pour poncer les peintures pour plus d’informations quant au ponçage des
peintures.

• Nettoyer l’outil régulièrement.

IMPORTANTS RENSEIGNEMENTS

· Ne pas appuyer trop fort sur l’outil; laisser ce dernier faire le travail.

· Il est déconseillé d’utiliser cet outil pour poncer des cloisons sèches pendant de
longues périodes.

CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.

MMOODDEE DD’’EEMMPPLLOOII DDUU

MMOOUUSSEE PPOONNCCEEUUSSEE--PPOOLLIISSSSEEUUSSEE

Merci d’avoir choisi Black & Decker!

Consulter le site Web

www.BlackandDecker.com/NewOwner

pour enregistrer votre nouveau produit.

À

LLIIRREE AAVVAANNTT DDEE RREETTOOUURRNNEERR CCEE PPRROODDUUIITT

PPOOUURR QQUUEELLQQUUEE RRAAIISSOONN QQUUEE CCEE SSOOIITT ::

Si des questions ou des problèmes surgissent après l’achat d’un produit Black & Decker,

consulter le site Web

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

Si la réponse est introuvable ou en l’absence d’accès à Internet, composer le

1-800-544-6986 de 8 h à 17 h HNE, du lundi au vendredi, pour parler avec un agent.

Prière d’avoir le numéro de catalogue sous la main lors de l’appel.

pour obtenir des réponses instantanément 24 heures par jour.