Black & Decker Lzr5 Instruction Manual

www.blackanddecker.co.uk
5
4
2
6
2
1
UK
Ireland
Australia
3
New Zealand
1
3
7
8
C
6
2
Intended use
This Black & Decker tool has been designed to project laser lines to aid in DIY applications. This tool is intended for consumer use only.
Safety instructions
Warning! When using battery-powered tools,
basic safety precautions, including the following, should always be followed to reduce the risk of fire, leaking batteries, personal injury and material damage.
Read all of this manual carefully before operating the tool.
Retain this manual for future reference.
When disposing of batteries, follow the instructions given
in the section “Protecting the environment”. Do not incinerate the batteries.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin contact.
Additional safety instructions for lasers
Warning! Laser radiation.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the work area well lit. Do not use the tool where there is a risk of causing fire or explosion, e.g. in the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the work area or to touch the tool.
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense. Do not operate the tool when you are tired.
Use appropriate tool
The intended use is described in this instruction manual. Warning! The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury.
Check for damaged parts
Before use, carefully check the tool for damage. Ensure that the tool will operate properly and perform its intended function. Do not use the tool if any part is damaged or defective.
Store idle tools
When not in use, tools and batteries should be stored in a dry, locked up or high place, out of reach of children.
Repairs
This tool complies with relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user.
Additional safety instructions for non-rechargeable batteries
Never attempt to open for any reason.
Do not store in locations where the temperature may
exceed 40 °C.
Do not look into the laser beam.
Do not view the laser beam directly with optical instruments.
Refer to the laser product characteristics.
This laser complies with class 2 according to
EN 60825-1:1 1994+A11. Do not replace a laser diode with a different type. If damaged, have the laser repaired by an authorised repair agent.
Do not use the laser for any purpose other than projecting
laser lines.
An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds. Eyelid reflexes will normally provide adequate protection. At distances over 1 m, the laser complies with class 1 and thus is considered completely safe.
Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
Do not set up the tool at a position where the laser beam
can cross any person at head height.
Do not let children come near the laser.
Features
1. On/off switch
2. Laser apertures
3. Battery cover
4. Hanging insert
5. Keyhole insert
6. Marking target
Assembly
Warning! Make sure that the tool is switched off.
Fitting the battery (fig. A)
Remove the battery cover (3) from the tool.
Connect the battery to the connector.
3
The larger battery terminal connects to the smaller connector terminal.
Insert the battery into the tool in the orientation as shown.
Refit the cover and let it click into place.
Fitting and removing inserts
The marking/hanging insert is used to make a mark on the level line or to hang the tool on a drywall board using the drywall pin supplied. The keyhole insert is used to hang the tool on other types of wall using a screw or nail.
Fitting
Place the insert into the holder from the back of the tool.
Align the notches on the insert with the recesses in the
insert holder.
Let the insert click into place.
Removing
Keep the notches on the insert depressed.
Push the insert out of the holder.
Wall mounting (fig. B)
The unit can be mounted to walls using one of the inserts (4 or 5).
Hanging insert
The hanging insert (4) can be used for mounting to drywall surfaces only.
Mount the insert to the tool.
Remove the protective cap (7) from the pin (8) and store it
on the insert as shown (fig. B).
Hold the unit in front of a suitable location and press the
pin straight into the wall.
Warning! The pin of the insert is sharp and should be handled with care. Replace the protective cap immediately after removing the insert from the wall.
Keyhole insert
For surfaces other than drywall, the keyhole insert (5) can be used with a screw in a predrilled hole.
Mount the insert to the tool.
Hang the unit on a screw mounted on a suitable location.
Use
Using the laser level function (fig. C)
Using the laser in auto-leveling mode
Place the tool flat against the wall.
Push the on/off switch (1) up to switch the tool on in
auto-leveling mode.
Move the tool as necessary to position the laser line.
If necessary, hang the unit on the wall using the
appropriate insert. Note: the laser lines will only be level if the tool is kept within 5° from vertical.
Using the laser in locked/layout mode
When operating in the locked/layout mode, the tool can be held in any position, e.g. to project slope lines.
Place the tool flat against the wall.
Push the on/off switch (1) down to switch the tool on in
locked/layout mode.
Move the tool as necessary to position the laser line.
If necessary, hang the unit on the wall using the
appropriate insert.
Hints for optimum use
If because of the lighting conditions it is difficult to see
the laser line, or if the laser line has to be transferred
over long distances, you can use the marking target (6) to
enhance laser line (fig. D).
Protecting the environment
Tools
Should you find one day that your tool needs replacement, or if it is of no further use to you, think of the protection of the environment. Black & Decker repair agents will accept old Black & Decker tools and ensure that they are disposed of in an environmentally safe way.
Battery
If you want to dispose of the tool yourself, the battery must be removed as described above and disposed of in accordance with local regulations.
Place the battery in a suitable packaging to ensure that
the terminals cannot be short-circuited. Take the batteries
to a local recycling station.
Technical data
LZR5 BDL400S
Voltage V 9 9 Battery size 6LR61 6LR61 Laser class 2 2 Operating temperature °C 0 - 40 0 - 40 Weight kg 0.3 0.3
4
EC declaration of conformity
LZR5/BDL400S
Black & Decker declares that these products conform to:
EN 61010, EN 60825, EN 61000
Peter Holmes, Director of Engineering
Black & Decker, 56 Bai Yu Road
Suzhou Industrial Park
Suzhou, Jiangsu, 215021
Guarantee
Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless:
The product has been used for trade, professional or hire
purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign
objects, substances or accidents;
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk
5
678
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100 20 Fletcher Road, Mooroolbark, Fax 03-9727 5940 Victoria, 3138
New Zealand
Black & Decker Tel. 09 579 7600 81 Hugo Johnston Drive Fax 09 579 8200 Penrose, Auckland, New Zealand
United Kingdom
Black & Decker Tel. 01753 511234 210 Bath Road Fax 01753 551155 Slough, Berkshire SL1 3YD Helpline 01753 574277
585435-02
12/03
Loading...