www.blackanddecker.com
876
9
1
9
5
4
2
3
UK
Ireland
Australia
New Zealand
1
A
11
10
3
8
B
C
2
D
E
3
Intended use
This Black & Decker tool has been designed to project laser
lines to aid in DIY applications and to detect studs covered by
wall boards. This tool is intended for consumer use only.
Safety instructions
◆ Warning! When using battery-powered tools, basic
safety precautions, including the following, should always
be followed to reduce the risk of fire, leaking batteries,
personal injury and material damage.
◆ Read all of this manual carefully before operating the tool.
◆ Retain this manual for future reference.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts.
Preferably wear rubber gloves and non-slip footwear when
working outdoors. Wear protective hair covering to keep long
hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles. Wear ear
protection whenever the sound level seems uncomfortable.
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool for damage. Check for
misalignment and seizure of moving parts, breakage of parts,
damage to guards and switches and any other conditions that
may affect its operation. Ensure that the tool will operate
properly and perform its intended function. Do not use the tool
if any part is damaged or defective. Do not use the tool if the
switch does not turn it on and off. Have any damaged or
defective parts repaired or replaced by an authorised repair
agent. Never attempt any repairs yourself.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Store idle tools
When not in use, tools and batteries should be stored in a dry,
locked up or high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
Additional safety instructions for lasers
◆ This laser complies with class 2 according to
EN 60825-1:1994+A11. Do not replace a laser diode with
a different type. If damaged, have the laser repaired by an
authorised repair agent.
◆ Do not use the laser for any purpose other than projecting
laser lines.
◆ An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds.
Eyelid reflexes will normally provide adequate protection.
At distances over 1 m, the laser complies with class 1 and
thus is considered completely safe.
◆ Never look into the laser beam directly and intentionally.
◆ Do not use optical tools to view the laser beam.
◆ Do not set up the tool at a position where the laser beam
can cross any person at head height.
◆ Do not let children come near the laser.
Additional safety instructions for non-rechargeable
batteries
◆ Never attempt to open for any reason.
◆ Do not store in locations where the temperature may
exceed 40 °C.
◆ When disposing of batteries, follow the instructions given
in the section “Protecting the environment”.
Do not incinerate the batteries.
4
◆ Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, proceed as
follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
Features
1. On/off switch (laser)
2. On/off switch (stud finder)
3. Battery cover
4. LED indicators
5. Insert holder
6. Marking/hanging insert
7. Keyhole insert
8. Spacer insert
9. Laser apertures
Assembly
Fitting the battery (fig. A)
◆ Depress the release button (10) and slide the battery
cover (3) off the tool.
◆ Connect the battery to the connector. The larger battery
terminal connects to the smaller connector terminal.
◆ Refit the cover and let it click into place.
Fitting and removing inserts
The marking/hanging insert is used to make a mark on the
level line or to hang the tool on a drywall board using the
drywall pin supplied. The keyhole insert is used to hang the
tool on other types of wall using a screw or nail. The spacer
insert is used to extend the laser line.
Fitting
◆ Place the insert into the holder from the back of the tool.
◆ Align the notches on the insert with the recesses in the
insert holder.
◆ Let the insert click into place.
Note: the laser lines will only be level if the tool is kept within
5° from vertical.
Using the spacer insert (fig. C)
If you need to extend the laser line, use the spacer insert as
shown.
Note: the stud sensor cannot be used with the spacer insert
fitted.
Enhancing the visibility of the beam (fig. D)
If because of the lighting conditions it is difficult to see the
laser line, you can use one of the inserts as shown to enhance
the line.
Using the stud finder function (fig. E)
You can use this function to find wooden or metal studs
through drywall boards up to 18 mm thick.
◆ Fit the marking insert (6).
◆ Place the tool flat against the wall as shown.
◆ Keep the on/off switch (2) depressed.
The red LED indicator (4) will light up and the tool will beep
once while it is calibrating. When this is completed:
◆ Slowly slide the tool in a horizontal direction. Make sure
not to tilt or lift the tool.
◆ When the red LED indicator (4) lights up, slow down and
slide the tool further until the tool beeps and the top
green LED indicator is lit.
This indicates the position of one edge of the stud.
◆ Mark this position through the hole in the marking insert (6).
◆ Move the unit further until the LED indicators go out.
◆ While still keeping the on/off switch (2) depressed, move
the tool in the opposite direction.
◆ When the red LED indicator (4) lights up, slow down and
slide the tool further until the tool beeps and the top
green LED indicator is lit.
This indicates the position of the other edge of the stud.
◆ Mark this position through the hole in the marking insert (6).
The centre of the stud is between the two marks.
Removing
◆ Keep the notches on the insert depressed.
◆ Push the insert out of the holder.
Use
Using the laser level function (fig. B)
◆ Place the tool flat against the wall as shown.
◆ Push the on/off switch (1) up to switch the tool on.
◆ Move the tool as necessary to position the laser lines.
◆ If necessary, hang the unit on the wall using the
appropriate insert.
Protecting the environment
Tools
Should you find one day that your tool needs replacement, or
if it is of no further use to you, think of the protection of the
environment. Black & Decker repair agents will accept old
Black & Decker tools and ensure that they are disposed of in
an environmentally safe way.
Battery
If you want to dispose of the tool yourself, the battery must be
removed as described above and disposed of in accordance
with local regulations.
5
Place the battery in a suitable packaging to ensure that the
terminals cannot be short-circuited. Take the batteries to a
local recycling station.
Technical data
LZR1
Voltage V 9
Battery size 6LR61
Laser class II
Operating temperature °C 0 - 40
Weight kg 0.45
EC declaration of conformity
LZR1
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014,
EN 50260
Peter Holmes, Director of Engineering
BDCI, 4/F, 2 Dai Wang Street
Tai Po Industrial Estate
Tai Po NT, Hong Kong
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
6
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road Tel. 03 9895 9200
Box Hill, Victoria 3128 Fax 03 9899 7465
New Zealand
Black & Decker Tel. 09 579 7600
81 Hugo Johnson Drive Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker Tel. 01753 511234
210 Bath Road Fax 01753 551155
Slough, Berkshire SL1 3YD Helpline 01753 574277
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
✁
Yes
No
Was this tool bought as a replacement?
.........
.........
..........
....
...............
...............
Data protection act:
Tick the box if you prefer not to receive further information.
...............................................................................................................................
...............................................................................................................................
Dealer address: ................................................................................................................
.......
Dealer address Date of purchase
Yes
No
Name: ..........................................................................................................................
Address:.......................................................................................................................
Town: ..........................................................................................................................
Postal code: ...................................................................................................................
Was this tool a gift?
Yes
No
Was this tool your first purchase?
7
✁
Please complete this section immediately after the purchase of your tool and send it to Black & Decker in your country.
If you live in Australia or New Zealand, please register by using the alternative guarantee card supplied.
GUARANTEE CARD
581793-02
8
Loading...