Page 1
1 2
www.blackanddecker.com
67 5
43
UK
Ireland
Australia
New Zealand
1
Page 2
A
6
5
5
C
D
2
3 4
8
7
B
6
E
Page 3
Intended use
Your Black & Decker sander has been designed for sanding
wood, metal, plastics and painted surfaces. This tool is
intended for consumer use only.
Safety instructions
◆ Warning! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock, personal
injury and material damage.
◆ Read all of this manual carefully before operating the tool.
◆ Retain this manual for future reference.
◆ Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool or mains cable.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn whenever the sound level
seems uncomfortable.
Guard against electric shock
Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators). Electric safety
can be further improved by using a high-sensitivity
(30 mA / 30 mS) residual current device (RCD).
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
Extension cables
Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use. Up to 30 m of Black & Decker
extension cable can be used without loss of power.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool. Do not
use the tool for purposes not intended, for example, do not
use a circular saw to cut tree limbs or logs.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving parts,
breakage of parts, damage to guards and switches and any
other conditions that may affect its operation. Ensure that the
tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.
Unplug the tool
Unplug the tool when it is not in use, before changing any parts
of the tool, accessories or attachments and before servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when plugging in.
Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the
socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
3
Page 4
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
◆ If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for sanders
◆ Always wear a dust mask whenever sanding.
◆ Thoroughly remove all dust after sanding.
◆ Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
- Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that persons
within or entering the work area are also protected.
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
Features
1. On/off switch
2. Gel comfort grip
3. Dust extraction outlet
4. Dust bag
5. Sanding base
6. Paper clamp lever
7. Paper punch
Assembly
Warning! Make sure that the tool is switched off and
unplugged.
Fitting regular sanding sheets (fig. B)
◆ Make sure that the tool is switched off and unplugged.
◆ Soften the sanding sheet by rubbing its non-abrasive side
over the edge of a worktop.
◆ Press the paper clamp levers (6) upwards to release them
from the retaining grooves and open the paper clamps by
pressing them down.
◆ Place the sheet onto the sanding base.
◆ Insert the edge of the sanding sheet into the front paper
clamp as shown.
◆ Press the front paper clamp lever (6) downwards and
locate it in the retaining groove.
◆ While keeping a slight tension on the sheet, insert the
rear edge of the sheet into the rear paper clamp.
◆ Press the rear paper clamp lever (6) downwards and
locate it in the retaining groove.
Punching sanding sheets (fig. C)
The paper punch (7) is used for punching dust extraction holes
in sanding sheets without pre-punched holes. For optimum
convenience the paper punch can be fitted to a workbench
using the screw holes (8).
◆ Fit a sanding sheet.
◆ Hold the tool in position right above the paper punch (7).
◆ Press the tool with the sanding base (5) down into the
paper punch.
◆ Take the tool off the paper punch and check whether the
holes in the sanding sheet have been fully pierced.
Fitting and removing the dustbag (fig. D)
◆ Fit the dustbag (4) over the dust extraction outlet (3).
◆ To remove the dustbag, pull the dustbag to the rear and
off the outlet.
Use
Switching on and off
◆ To switch the tool on, press the I part of the on/off switch
(1).
◆ To switch the tool off, press the O part of the on/off switch.
Fitting sanding sheets (fig. A - C)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (fig. A)
◆ Make sure that the tool is switched off and unplugged.
◆ Press the sheet firmly and evenly onto the sanding base
(5), making sure that the holes in the sheet line up with
the holes in the base.
4
Emptying the dustbag
The dustbag should be emptied every 10 minutes.
◆ Shake the dustbag to empty the contents.
Hints for optimum use
(fig. E)
◆ Hold the tool as shown.
◆ Do not exert too much pressure on the tool.
◆ Regularly check the condition of the sanding sheet.
Replace when necessary.
◆ Always sand with the grain of the wood.
Page 5
◆ When sanding new layers of paint before applying
another layer, use extra fine grit.
◆ On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
◆ Consult your retailer for more information on available
accessories.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
◆ Regularly clean the ventilation slots with a clean,
dry paint brush.
◆ To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
◆ Safely dispose of the old plug.
◆ Connect the brown lead to the live terminal in the new plug.
◆ Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014,
EN 61000
LpA (sound pressure): 72 dB(A), LWA (acoustic power) 85 dB(A),
hand/arm weighted vibration < 2.5 m/s
2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Technical data
KA170GT
Voltage VAC230
Power input W 170
Oscillations (no load) min-126,000
Orbits (no load) min-113,000
Weight kg 1.25
Please register at our website www.blackanddecker.com
to be kept up to date on new products and special offers.
Further information on the Black & Decker brand and our range
of products is available at www.blackanddecker.com.
5
Page 6
KA170GT
TYP
1
20
22
21
14
4
12
6
5
13
3
15
20
17
2
1
19
4
16
11
7
8
9
10
WWW.2helpU.com 15-07-03E13676
6
Page 7
7
Page 8
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road Tel. 03 9895 9200
Box Hill, Victoria 3128 Fax 03 9899 7465
New Zealand
Black & Decker Tel. 09 579 7600
81 Hugo Johnston Drive Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker Tel. 01753 511234
210 Bath Road Fax 01753 551155
Slough, Berkshire SL1 3YD Helpline 01753 574277
584776-01
8
07/03
Loading...