Black & decker KA161K User Manual

www.blackanddecker.com

1

2

6

4
8
5

7

3

9

UK

Ireland

Australia

New Zealand

1

A

11

10

10

14

11

5

8

4

12
8
6

4

8
7

4

9

7

9

7

C

D

F1

2

B

E

F2

1

2

13

G

J

9

H

I

3

Intended use

Your Black & Decker sander has been designed for sanding
and polishing wood, metal, plastics and painted surfaces.
This tool is intended for consumer use only.

Safety instructions

◆ Warning! When using mains-powered tools, basic safety

precautions, including the following, should always be
followed to reduce the risk of fire, electric shock,
personal injury and material damage.

◆ Read all of this manual carefully before operating the tool.

◆ Retain this manual for future reference.

◆ Remove the plug from the socket before carrying out any

adjustment, servicing or maintenance.

Keep work area clean

Cluttered areas and benches can cause accidents.

Consider work area environment

Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.

Keep children away

Do not allow children, visitors or animals to come near the
work area or to touch the tool or mains cable.

Dress properly

Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.

Personal protection

Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.

Guard against electric shock

Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators).
Electric safety can be further improved by using a high­sensitivity (30 mA / 30 mS) residual current device (RCD).

Do not overreach

Keep proper footing and balance at all times.

Stay alert

Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.

Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.

Connect dust extraction equipment

If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.

Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.

Extension cables

Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use. Up to 30 m of Black & Decker
extension cable can be used without loss of power.

Use appropriate tool

The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool. Do not
use the tool for purposes not intended, for example, do not
use a circular saw to cut tree limbs or logs.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.

Check for damaged parts

Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving parts,
breakage of parts, damage to guards and switches and any
other conditions that may affect its operation. Ensure that the
tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.

Unplug the tool

Unplug the tool when it is not in use, before changing any
parts of the tool, accessories or attachments and before
servicing.

Avoid unintentional starting

Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when plugging in.

Do not abuse cord

Never carry the tool by its cord or pull it to disconnect from the
socket. Keep the cord away from heat, oil and sharp edges.

Store idle tools

When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.

Maintain tools with care

Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.

Repairs

This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.

4

Electrical safety

This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.

Additional safety instructions for sanders

◆ Always wear a dust mask whenever sanding.

◆ Thoroughly remove all dust after sanding.

◆ Before using the tool on wooden workpieces, make sure

to fit dust extraction equipment.

◆ Before using the tool on metal workpieces, make sure to

remove the dust extraction equipment.

◆ Never use the tool without a sanding sheet.

◆ Never use the tool without a sanding base.

◆ Hearing protection should be worn whenever the sound

level seems uncomfortable.

Sanding lead-based paint or MDF

Sanding of lead-based paint is not recommended due to the
difficulty of controlling the contaminated dust. The greatest
danger of lead poisoning is to children and pregnant women.
Any pre-1960 building may in the past have been painted with
paint containing lead. This paint may be covered with additional
layers of paint. Before starting work, it is important to
determine whether the paint to be sanded contains lead.
This can be done using a test kit or by a professional decorator.

Personal protection

◆ Do not let children or pregnant women enter the work area.

◆ Wear a dust mask specifically designed for protection

against lead paint dust and fumes and ensure that persons
within or entering the work area are also protected.

◆ Do not eat, drink or smoke in the work area. Do not store

any food or drink in the work area.

◆ Wash yourself very carefully before eating, drinking or

smoking.

Environment

◆ Remove the paint in such a way that the amount of dust is

minimised.

◆ Seal the work area with plastic sheeting.

◆ Minimise the amount of dust outside the work area.

Cleaning

◆ Thoroughly vacuum and clean all surfaces in the work

area every day.

◆ Regularly change the dustbag and filters of the vacuum

cleaner.

◆ Thoroughly wash any foreign objects exposed to dust

before using them again.

Additional safety instructions for Australia and New
Zealand

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised
to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Dust extraction connector

3. Base

4. Tip holder

5. Sanding base tip

6. Finger attachment

7. Profile attachment

8. Screw

9. Sanding profiles

In addition, this tool is supplied with some or all of the
following accessories:

Accessory Recommended application

and use

- Coarse grit sandpaper Fast paint, varnish and rust
removal

- Medium grit sandpaper Paint, varnish and rust removal

- Fine grit sandpaper Surface blending and finishing

- Extra fine grit sandpaper Sanding between coats

- Detail sanding tips Corners and hard to reach places

- 1 OT polishing/ Polishing metals, stripping

stripping wool varnish and glass cleaning

- Grey foam pad Applying and removing polish

- Red non-woven pad Heavy scrubbing and rust removal

- Grey abrasive paper Polishing plastics

- Contour attachments Curves and profiles

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting sanding sheets (fig. A & B)

◆ Detach the two diamond-shaped tips (10) from the

sanding sheet (11).

◆ Hold the tool with the sanding base facing upwards.

◆ Place the sanding sheet (11) onto the sanding base,

making sure that the holes in the sheet line up with the

holes in the base.
The diamond-shaped tip (10) can be reversed and replaced
when worn.

5

◆ When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

◆ When the whole tip is worn, remove it from the sanding

base and fit a new tip.

◆ The polishing foam and pads (14) can be fitted the same

way as the sanding sheets.

Tip of the sanding base (fig. C)

When the sanding base tip (5) or tip holder (4) is worn, it can
be reversed or replaced. Spare parts are available from your
Black & Decker dealer.

◆ Remove the screw (8).

◆ Reverse or replace the worn part.

◆ Fit and tighten the screw.

Finger attachment (fig. D)

The finger attachment is used for fine detail sanding.

◆ Remove the screw (8).

◆ Remove the diamond-shaped tip holder (4) from the

sanding base.

◆ Fit the finger attachment (6) onto the sanding base.

◆ Fit and tighten the screw.

◆ Fit the appropiate sanding sheet (12) onto the finger

attachment.

Connecting a vacuum cleaner (fig. I)

The tool has an adaptor to connect it to a vacuum cleaner
when sanding wood. To connect the tool to a vacuum cleaner,
proceed as follows:
Warning! Make sure that the tool is switched off and unplugged.

◆ Fit the dust extraction connector (2) onto the adapter at

the back of the tool.

◆ Connect the hose of a suitable vacuum cleaner to the

connector.

Switching on and off (fig. J)
Warning! Before connecting the tool to the power supply,

make sure it is switched off.

◆ To switch the tool on, press the part of the on/off switch (1)

marked ‘I’.

◆ To switch the tool off, press the part of the on/off switch (1)

marked ‘0’.

Accessories

The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.

Profile attachment (KA161K only) (fig. E)

The profile attachment is used for contour sanding.

◆ Remove the screw (8).

◆ Remove the diamond-shaped tip holder (4) from the

sanding base.

◆ Fit the profile attachment (7) onto the sanding base.

◆ Fit and tighten the screw.

Fitting and removing a sanding profile (fig. F1 & F2)

◆ Choose the sanding profile most suitable for your application.

◆ Place one end of the sanding profile (9) into the recess at

the front end of the profile holder (7).

◆ Push the other end of the sanding profile until it clicks

into place.

◆ To remove the sanding profile, push it forward and pull

the rear end out of the profile holder (fig. F2).

Fitting a sanding sheet onto a sanding profile (fig. G)

◆ Align the sanding sheet (13) with the sanding profile (9).

◆ Press the sanding sheet onto the sanding profile, making

sure that the sanding sheet follows the shape of the profile.

Use

Warning! Do not cover the ventilation slots when using the

tool. Hold the tool as shown in fig. H. Make sure that the
sanding base is flat on the workpiece.

6

Maintenance

Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.

◆ Clear the cooling vents and slots with a clean, dry paint

brush.

◆ Clean the housing with a clean, damp cloth. Do not use

solvents.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

◆ Safely dispose of the old plug.

◆ Connect the brown lead to the live terminal in the new plug.

◆ Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.

Protecting the environment

Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.

You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.

Technical data

KA161/KA161K

Voltage VAC230
Power input W 55
No-load speed min-111,000

EC declaration of conformity

Black & Decker declares that these products, KA161/KA161K,

conform to:

98/37/EC, 89/336/EEC, 73/23/EEC, EN50144, EN55014,

EN61000

LpA (sound pressure): 66 dB(A), LWA (acoustic power) 79 dB(A),

hand/arm weighted vibration < 2.5 m/s

2

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG,

United Kingdom

Guarantee

Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade Area.

To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.

If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:

◆ The product has been used for trade, professional or hire

purposes;

◆ The product has been subjected to misuse or neglect;

◆ The product has sustained damage through foreign

objects, substances or accidents;

◆ Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

Australia

DEWALT Industrial Power Tool Company
7 Clarice Road Tel. [phone]
Box Hill, Victoria 3128 Fax [phone]

New Zealand

Black & Decker Tel. [phone]
81 Hugo Johnson Drive Fax [phone]
Penrose, Auckland, New Zealand

United Kingdom

Black & Decker Tel. [phone]
210 Bath Road Fax [phone]
Slough, Berkshire SL1 3YD Helpline 01753 574277

7

KA161 - KA161K

101

TYP

1

E13387 / 582158-00

8

105

106

103

102

WWW.2helpU.com

104

KA161K

27 - 06 - 02

91011

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

✁

Yes

No

Was this tool bought as a replacement?

.........

.........

..........

....

...............

...............

Data protection act:

Tick the box if you prefer not to receive further information.

...............................................................................................................................

...............................................................................................................................

Dealer address: ................................................................................................................

.......

Dealer address Date of purchase

Yes

No

Name: ..........................................................................................................................

Address:.......................................................................................................................

Town: ..........................................................................................................................

Postal code: ...................................................................................................................

Was this tool a gift?

Yes

No

Was this tool your first purchase?

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

✁

Please complete this section immediately after the purchase of your tool and send it to Black & Decker in your country.

If you live in Australia or New Zealand, please register by using the alternative guarantee card supplied.

GUARANTEE CARD

12

582157-03