Black & Decker HT2200-CA, 90512417, HT22D, TR1800-CA, HS1010-CA User Manual

Catalog Nos. TR1800, TR1800-CA
HT2200, HT2200-CA, HT22D,
HS1010, HS1010-CA

WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this tool reads and understands all safety
instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

CAUTION: Wear appropriate personal hearing protection during use. Under some
conditions and duration of use, noise from this product may contribute to hearing loss.
WARNING: When using electric gardening appliances, basic safety precautions should

always be followed to reduce risk of fire, electric shock, and personal injury, including the
following:

READ ALL INSTRUCTIONS.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS

• AVOID DANGEROUS ENVIRONMENT - Don’t use hedge trimmers in damp or wet
locations.

• DON’T USE IN RAIN.

• KEEP CHILDREN AWAY - All visitors should be kept at a safe distance from the work
area.

• DRESS PROPERLY - Don’t wear loose clothing or jewelry. They can be caught in moving
parts. Use of rubber gloves and substantial footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.

• USE SAFETY GLASSES - Also use face or dustmask if operation is dusty.

• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the
circuit(s) or outlet(s) to be used for the hedge trimmer. Receptacles are available having
built-in GFCI protection and may be used for this measure of safety.

• USE RIGHT APPLIANCE - Do not use appliance for any job except that for which it is
intended.

WARNING: To reduce the risk of electric shock use only with an extension cord intended
for outdoor use, such as SW-A, S0W-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A or
SJTOW-A.

• EXTENSION CORD. Make sure your extension cord is in good condition. When using an
extension cord be sure it is heavy enough to carry the current your product will draw. An
undersized extension cord will cause a drop in line voltage resulting in loss of power and
overheating. The following table shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage
number, the heavier the cord.

• AVOID UNINTENTIONAL STARTING - Don’t carry plugged in hedge trimmer with finger
on switch. Be sure switch is off when plugging in.

• DON’T ABUSE CORD - Never carry hedge trimmer by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.

DANGER: Risk of cut. Keep hands away from blades. Keep both hands on handles when

power is on.

• DO NOT ATTEMPT to remove cut material or hold material to be cut when blades are
moving. Make sure trimmer switch is off when clearing jammed material from blades. Do
not grasp the exposed cutting blades or cutting edges when picking up or holding the
hedge trimmer.

CAUTION: Blades coast after turn off.

• DON’T FORCE HEDGE TRIMMER - It will do the job better and with less likelihood of a
risk of injury at the rate for which it was designed.

• DON’T OVERREACH - Keep proper footing and balance at all times.

• STAY ALERT - Watch what you are doing. Use common sense. Do not operate hedge
trimmer when you are tired.

• DISCONNECT HEDGE TRIMMER from the power supply when not in use or when
servicing or cleaning.

• STORE IDLE HEDGE TRIMMER INDOORS - When not in use, hedge trimmer should be
stored indoors in a dry and high or locked-up place- out of reach of children.

• MAINTAIN HEDGE TRIMMER WITH CARE - Keep cutting blades sharp and clean for
best performance and to reduce the risk of injury. Inspect extension cord periodically and
replace if damaged. Keep handles dry, clean and free from oil and grease.

• CHECK DAMAGED PARTS - before further use of the hedge trimmer, a guard or other
part that is damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other condition that may affect its operation. A
guard or other part that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated elsewhere in this manual.

SAFETY WARNINGS: DOUBLE INSULATION

Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool’s electrical
system. Tools built with this insulation system are not intended to be grounded. As a result,
your tool is equipped with a two prong plug which permits you to use extension cords
without concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting
from a possible electrical insulation failure within the tool.
Replacement parts: When servicing all tools, USE IDENTICAL REPLACEMENT PARTS.
Repair or replace damaged cords.

SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the
other). This equipment must be used with a suitable polarized 2 wire or 3 wire extension cord. Polarized
connections will fit together only one way. Make sure that the receptacle end of the extension cord has
large and small blade slot widths. If the plug does not fit fully into the extension cord, reverse the plug. If it
still does not fit, obtain a suitable extension cord. If the extension cord does not fit fully into the outlet,
contact a qualified electrician to install the proper outlet. Do not change the tool plug or extension cord in
any way.

SPECIFIC SAFETY WARNING

WARNING: Some dust created by this product contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber
To reduce your exposure to these chemicals, wear approved safety equipment such as
dust masks that are specially designed to filter out microscopic particles.

CAT. NOs. TR1800, TR1800-CA, HT2200, HT2200-CA, HT22D, HS1010, HS1010-CA FORM NO. 90512417
(NOV. -06) Copyright © 2006 Black & Decker PRINTED IN MEXICO

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

4

5

ATTACHING BAIL HANDLE TO TRIMMER (TR1800, HT2200, HT22D & HS1010 ONLY)

WARNING: Do not operate the hedge trimmer without the bail handle attached.

The trimmer is shipped with the bail handle tied to the trimmer. To attach the bail handle:

• Cut the ziptie which holds the handle to the trimmer.

• Remove the phillips head screws from both sides of the trimmer housing.

• Position the handle in place as shown in figure 1 (TR1800, HT2200, HT22D) or figure 1A
(HS1010).

• Reinsert the phillips head screws into the openings on the side of the handle and tighten
securely.

ATTACHING EXTENSION CORD TO TRIMMER

An extension cord retainer is built into the switch handle that prevents the tool from coming
unplugged. To use this feature, simply double the extension cord about 8 inches from the
end, and insert it into the slot in the bottom of the handle area. Hook the loop formed by
doubling the cord over the tab, as shown in figure 2 (TR1800, HT2200, HT22D) or figure
2A (HS1010). Gently tug on the cord to insure that it is firmly retained in the trimmer’s
handle. Plug the receptacle end of the extension cord into the plug blades in the trimmer.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage
Than Than
0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

7

KEY INFORMATION YOU SHOULD KNOW:

• To insure extension cord does not come loose see Figures 2 and 2A for proper

attachment.

• In order to operate the trimmer, the lock button must first be pulled back

(see figure 3) then squeeze trigger.

3

Lock Button

Bouton de verrouillage

Botón de seguridad

Trigger

Gâchette

Interruptor de

Gatillo

Plug Blades

Raccordement à fiche

Clavijas de enchufe

DATE CODE

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU

HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO

BLACK & DECKER.

T

T

HANK

HANK

YOU

YOU

FOR

FOR

CHOOSING

CHOOSING

B

B

LACK

LACK

&&D

D

ECKER

ECKER

!

!

G

G

OOTTOOWWW

WWW

.B

.B

LACKAND

LACKAND

D

D

ECKER

ECKER

.

.

COM

COM

/N

/N

EW

EW

O

O

WNER

WNER

TTOOREGISTER

REGISTER

YOUR

YOUR

NEW

NEW

PRODUCT

PRODUCT

.

.

1

2

6

1A

2A

MESURES DE SÉCURITÉ POUR TOUS LES OUTILS

• NE PAS UTILISER DANS UN ENVIRONNEMENT DE TRAVAIL DANGEREUX. Ne pas
utiliser le taille-haie dans des endroits humides ou mouillés.

• PROTÉGER DE LA PLUIE.

• ÉLOIGNER LES ENFANTS. Tous les visiteurs doivent être gardés à une distance sûre de
l’aire de travail.

• PORTER DES VÊTEMENTS APPROPRIÉS. Éviter de porter des vêtements amples et des
bijoux qui peuvent être happés par les pièces en mouvement. Porter des gants de
caoutchouc et des chaussures à semelle antidérapante pour travailler à l’extérieur.
Protéger la chevelure si elle est longue.

• TOUJOURS PORTER DES LUNETTES DE SÉCURITÉ. Il faut également porter un
masque respiratoire si le travail produit de la poussière.

• Il faut installer un DISJONCTEUR DIFFÉRENTIEL sur le ou les circuits ou prises utilisés
pour alimenter le taille-haie. Il existe des prises à disjoncteur différentiel intégré et on peut
s’en servir par mesure de sécurité.

• UTILISER L’OUTIL APPROPRIÉ. – Utiliser l’outil seulement aux fins pour lesquelles il a été
conçu.

AVERTISSEMENT : Afin de prévenir les risques de secousses électriques, utiliser
seulement un cordon de rallonge prévu pour l’extérieur (SW-A, SOW-A, STW-A, STOW-A,
SJW-A, SJOW-A, SJTW-Aou SJTOW-A).

• CORDON DE RALLONGE - S’assurer que le cordon de rallonge est en bon état. Lorsqu’on
se sert d’un cordon de rallonge, s’assurer qu’il est de calibre approprié pour la tension
nécessaire au fonctionnement de l’outil. L’utilisation d’un cordon de calibre inférieur
occasionne une baisse de tension entraînant une perte de puissance et la surchauffe. Le
tableau de la page suivante indique le calibre approprié selon la longueur du cordon et les
mentions de la plaque signalétique de l’outil. En cas de doute, utiliser un cordon de calibre
supérieur. Le chiffre indiquant le calibre est inversement proportionnel au calibre du cordon.
Black & Decker offre des cordons de rallonge trifilaires mis à la terre prévus pour l’extérieur.

• ÉVITER LES DÉMARRAGES ACCIDENTELS. Ne pas laisser le doigt sur l’interrupteur
lorsqu’on transporte le taille-haie. S’assurer que l’interrupteur est en position hors circuit
lorsqu’on branche l’outil.

• NE PAS MANIPULER LE CORDON DE FAÇON ABUSIVE. Ne pas transporter l’outil par le
cordon ni tirer sur ce dernier pour le débrancher de la prise. Éloigner le cordon des sources
de chaleur, des flaques d’huile et des arêtes tranchantes.

DANGER : Risque de coupure. Éloigner les mains des lames. Laisser les deux mains sur

les poignées lorsque l’outil fonctionne.

• NE PAS TENTER d’enlever des matières coupées ni de débloquer le couloir d’éjection
lorsque la lame tourne. S’assurer que le taille-haie est hors tension avant de retirer les
matières coincées dans la lame. Ne jamais saisir les lames à découvert ni les arêtes
tranchantes lorsqu’on prend l’outil ou qu’on le tient.

MISE EN GARDE : La lame peut continuer de bouger après avoir mis l’outil hors tension.

• NE JAMAIS FORCER L’OUTIL. Afin d’obtenir un rendement sûr et efficace, utiliser l’outil à
son rendement nominal.

• NE PAS DÉPASSER SA PORTÉE. Toujours demeurer dans une position stable et garder
son équilibre.

• DEMEURER VIGILANT. Travailler avec vigilance et faire preuve de bon sens. Ne pas se
servir de l’outil lorsqu’on est fatigué.

• DÉBRANCHER LE TAILLE-HAIE. – Lorsqu’il ne sert pas, lorsqu’on le répare ou avant de
le nettoyer.

• RANGER LES TAILLE-HAIES INUTILISÉS. Il faut ranger les outils dans un endroit sec,
situé en hauteur ou fermé à clé, hors de la portée des enfants.

• PRENDRE SOIN DES OUTILS. Conserver les outils propres et bien affûtés pour qu’ils
donnent un rendement supérieur et sûr. Inspecter régulièrement les cordons de rallonge et
les remplacer lorsqu’ils sont endommagés. S’assurer que les poignées sont toujours
propres, sèches et libres de toute tache d’huile ou de graisse.

• VÉRIFIER LES PIÈCES ENDOMMAGÉES. Avant d’utiliser de nouveau l’outil, bien vérifier
un protecteur endommagé ou toute autre pièce défectueuse afin de déterminer si elle
fonctionnera de façon appropriée et si elle remplira la fonction prévue. Vérifier l’alignement et
les attaches des pièces mobiles, le degré d’usure des pièces et leur montage, ainsi que tout

OPERATING INSTRUCTIONS

TO TURN THE TOOL ON

Pull the LOCK BUTTON back with your thumb and then squeeze the TRIGGER with your
fingers as shown in Figure 3. (Once the tool is running you can release the LOCK
BUTTON.) To turn the tool OFF, release the TRIGGER.

TO LOCK THE TOOL ON FOR CONTINUOUS RUN

WITH THE TOOL RUNNING

, pull the LOCK BUTTON ALL THE WAYback, release the
TRIGGER, then release the LOCK BUTTON. The tool is now locked ON. To turn the tool
OFF, squeeze and release the TRIGGER. NOTE: In order to lock the tool on, it is important
to first release the trigger and then release the lock button.

TRIMMING INSTRUCTIONS

1 EXTENSION CORD – (Figure 4) Always keep extension cord behind trimmer and away

from the trimming operation. Never drape it over a hedge being trimmed. If you cut or
damage the cord, unplug it at the electrical outlet immediately, before inspecting or
repairing cord.

2 WORKING POSITION – Maintain proper footing and balance and do not overreach.

Wear safety goggles, non-skid footwear and rubber gloves when trimming. Hold the tool
firmly in both hands and turn the tool ON. Always hold the trimmer, as shown in figure
4, with one hand on the switch handle and one hand on the bail handle. Never hold the
tool by the blade guard.

3 TRIMMING NEW GROWTH - (Figure 5) – A wide, sweeping motion, feeding the blade

teeth through the twigs is most effective. A slight downward tilt of the blade, in the
direction of motion gives the best cutting.

CAUTION: Do not use the trimmer for cutting stems greater than 3/4” (10mm). Use the

trimmer only for cutting normal shrubbery found around houses and buildings.

4. LEVEL HEDGES (Figure 6) – To obtain exceptionally level hedges, a piece of string

can be stretched along the length of the hedge as a guide.

5. SIDE-TRIMMING HEDGES (Figure 7) – Begin at the bottom and sweep up.

WARNING: TO GUARD AGAINST INJURY, OBSERVE THE FOLLOWING:

• READ INSTRUCTION MANUAL BEFORE USING, SAVE INSTRUCTION MANUAL.

• KEEP HANDS AWAY FROM BLADES.

• KEEP HANDS ON HANDLES. DON’T OVERREACH.

• CAUTION: – BLADE COASTS AFTER TURN OFF.

• DO NOT USE UNDER WET CONDITIONS.

• DO NOT USE WITH DAMAGED EXTENSION CORD.

• DO NOT UNPLUG OR STORE WITH SWITCH LOCKED ON.

Troubleshooting

Problem Possible Cause Possible Solution

•Unit will not start. • Cord not plugged in. • Plug in cord.

• Circuit fuse is blown. • Replace circuit fuse.

• Circuit breaker • Reset circuit breaker.
is tripped.

• Cord or switch is • Have cord or switch
damaged. replaced at Black & Decker Service

Center or Authorized Servicer.

For assistance with your product, visit our website www.black&decker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

MAINTENANCE

The cutting blades are made from high quality, hardened steel and with normal usage, they
will not require resharpening. However, if you accidentally hit a wire fence, stones, glass or
other hard objects, you may put a nick in the blade. There is no need to remove this nick as
long as it does not interfere with the movement of the blade. If it does interfere, unplug unit
and use a fine toothed file or sharpening stone to remove the nick.
If you drop the trimmer, carefully inspect it for damage. If the blade is bent, housing
cracked, or handles broken or if you see any other condition that may affect the trimmer’s
operation, contact your local Black & Decker Service Center for repairs before putting it
back into use.
Fertilizers and other garden chemicals contain agents which greatly accelerate the
corrosion of metals. Do not store the tool on or adjacent to fertilizers or chemicals.
With the unit unplugged, use only mild soap and a damp cloth to clean the tool. Never let
any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.

Accessories

WARNING: DO NOT use the hedge trimmer with any type of accessory or attachment.

Such usage might be hazardous.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact
the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under "Tools–Electric"
or call:1-800-54-HOW TO (544-6986).

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways:
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may
be required. Black & Decker owned and authorized service centers are listed under
"Tools–Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

GUIDE D’UTILISATION

Taille-haies

RENSEIGNEMENTS IMPORTANTS

• Afin de s’assurer que la rallonge ne se débranche pas, la raccorder

conformément aux figures 2 and 2A .

• Pour faire fonctionner l’outil, on doit tirer sur le bouton de verrouillage (figure 3),

puis enfoncer l’actionneur vers le haut.

Calibre minimal des cordons de rallonge

Tension Longueur totale du cordon en pieds

120 V De 0 à 25 De 26 à 50 De 51 à 100 De 101 à 150
240 V De 0 à 50 De 51à 100 De 101 à 200 De 201 à 300

Intensité (A)
Au Au Calibre moyen de fil
moins plus

0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Non recommandé

AVERTISSEMENT : IMPORTANTES MESURES DE SÉCURITÉ

AFIN DE RÉDUIRE LES RISQUES DE BLESSURES :

• Avant toute utilisation, s’assurer que tous ceux qui se servent de l’outil lisent et
comprennent toutes les mesures de sécurité et tout autre renseignement contenu dans le
présent guide.

• Conserver ces mesures et les relire fréquemment avant d’utiliser l’outil et d’en expliquer le
fonctionnement à d’autres personnes.

MISE EN GARDE : Porter un dispositif approprié de protection de l’ouïe lors de
l’utilisation du produit. Dans certaines conditions et durées d’utilisation, le produit peut
émettre un niveau de bruit provoquant la perte de l’ouïe.

AVERTISSEMENT : Afin de réduire les risques d’incendie, de secousses électriques ou
de blessures lorsqu’on utilise des outils électriques, il faut toujours respecter les mesures
de sécurité suivantes.

LIRE TOUTES LES DIRECTIVES.

AAAAVVVVAAAANNNNTTTT DDDDEEEE RRRREEEETTTTOOOOUUUURRRRNNNNEEEERRRR CCCCEEEE PPPPRRRROOOOD

DDDUUUUIIIITTTT PPPPOOOOUUUURRRR QQQQUUUUEEEELLLLQQQQUUUUEE

EE

RRRRAAAAIIIISSSSOOOONNNN QQQQUU

UUEEEE CCCCEEEE SSSSOOOOIIIITTTT,,,, CCCCOOOOMMMMPPPPOOOOSSSSEEEERRRR LLLLEEEE NNNNUUUUMMMMÉÉÉÉRRRROOOO

SSSSUUUUIIIIVVVVAAAANNNNTTTT :::: 1111 888800000000 555544444444----66

66999988886666

MMMMEEEERRRRCCCCIIII DDDD’’’’AAAAVVVVOOOOIIIIRRRR CCCCHHHHOOOOIIIISSSSIIII BBBBLLLLAAAACCCCKKKK &&&& DDDDEEEECCCCKKKKEEEERRRR!!

!!

VVVVIIIISSSSIIIITTTTEEEEZZZZ WWWWWWWWWW

WW

....BBBBLLLLAAAACCCCKKKKAAAANNNNDDDDDDDDEEEECCCCKKKKEEEERRRR....CCCCOOOOMMMM////NNNNEEEEWWWWOOOOWWWWNNNNEEEERR

RR

PPPPOOOOUUUURRRR EEEENNNNRRRREEEEGGGGIIIISSSSTTTTRRRREEEERRRR VVVVOOOOTTTTRRRREEEE NNNNOOOOUU

UUVVVVEEEEAAAAUUUU PPPPRRRROOOODDDDUUUUIIIITTTT....