Black & Decker Gs500, 243147-00 User Manual

WARNING: IMPOR TANT SAFETY WARNINGS AND INSTRUCTIONS

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this garden appliance reads and understands all safety
instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

• WARNING: When using gardening appliances, basic safety precautions should always be

followed to reduce risk of fire, electric shock, and personal injury, including the
following.

• WARNING: This product contains chemicals, including lead, known to the State of California

to cause cancer , and birth defects or other reproductive harm. Wash hands after
handling.

• WARNING: Some dust created by this product contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber
To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks
that are specially designed to filter out microscopic particles.

CAUTION: Wear appropriate personal hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

READ ALL INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES

• AVOID DANGEROUS ENVIRONMENT . Don’ t use appliances in damp or wet locations. Don’t use

appliances in the rain.

• KEEP CHILDREN A WAY .All visitors should be kept at a distance from work area.

• STORE IDLE APPLIANCES INDOORS. When not in use, appliances should be stored indoors in

dry, and high or locked-up place – out of reach of children.

• DON’T FORCE APPLIANCE. It will do the job better and with less likelihood of a risk of injury at the

rate for which it was designed.

• USE RIGHT APPLIANCE. Do not use the appliance for any job except that for which it is intended.

• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts.

Rubber gloves and substantial, non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT . Use safety goggles or safety glasses

with side shields, complying with applicable safety standards and, when needed, a face shield.
Also use face or dust mask if operation is dusty . This applies to all persons in the work area. Also
use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified
or required. Safety glasses or the like are available at extra cost at your local dealer or Black &
Decker Service Center.

• MAINT AIN APPLIANCE WITH CARE. Keep cutting edge clean and sharp for best performance and

to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Keep
handles dry, clean, and free from oil and grease.

• AVOID UNINTENTIONAL STAR TING. Don’ t carry plugged-in appliance with finger on switch. Be

sure switch is off when plugging in.

• CHECK DAMAGED P ARTS.Before further use of the appliance, a guard or other part that is

damaged should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts, binding of moving parts, breakage of
parts, mounting, and any other condition that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an Authorized Service Center unless
otherwise indicated elsewhere in this manual.

• ST AY ALERT. Watch what you are doing. Use common sense. Do not operate appliance when you

are tired.

• REP AIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this manual

should be performed by Black & Decker Authorized Service Centers or other qualified service
organizations, always using identical replacement parts.

• USE OF ACCESSORIES AND A TTACHMENTS. The use of any accessory or attachment not

recommended for use with this appliance could be hazardous.

• DON’T GRASP THE EXPOSED CUTTING BLADES or cutting edges when picking up or holding the

appliance.

• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry the current your product will draw.

IMPORT ANT WARNINGS FOR GRASS SHEARS

1. Keep hands away from blades.

2. Do not charge the appliance in rain, or in wet locations.

3. Do not use battery operated appliance in rain.

WHEN USING YOUR CHARGER:

• The shear and its charger are specifically designed to work together. DO NOT attempt to
charge the shear with any other type of charger. DO NOT attempt to charge any other type
of cordless tool with the shear charger.

• DO NOT charge shear when temperature is below +40° or above +120°. This is very

important!

• DO NOT ABUSE THE CORD. Never carr y charger or shear by the cord or yank it to
disconnect the charger from a receptacle. Keep cord away from heat, oil, and sharp edges.

• DO NOT operate a damaged charger. Have damaged cords or plugs replaced immediately.

• Never expose charger to weather; use indoors only.

• The charger is designed to operate on standard household electrical power (120 volts). Do
not attempt to use it on any other voltage!

PREP ARING TO OPERATE:

THE BA TTERY IN YOUR NEW GRASS SHEAR IS NOT FULL Y CHARGED!
First, read the Safety Rules. Then follow the “Important Charging Notes” and “Charge the
Battery” sections.

IMPORT ANT CHARGING NOTES

1. Longest life and best performance can be obtained if the batteries are charged at normal
room temperatures.

2. While charging, the charger will normally become warm to the touch.

3. If the batteries do not charge properly:

a. Check house current at receptacle by plugging in a lamp or other appliance.
b. Check to see if receptacle is connected to a light switch which turns power off when you

turn out the lights.

c. If house current is okay and you do not get proper charging, contact your nearest

Black & Decker Service Center.

4. The grass shear should be recharged when it fails to produce sufficient power on jobs which
were done easily previously. Do not continue to use the unit under these conditions. Repeat
the charging procedure.

5. Unplug your shear’s charger from the power supply before disconnecting the charger from
the shear. Unplug charger before attempting to clean.

6. Battery life is dependent on usage, storage temperature and time. Replacement batter y packs
are available and should only be replaced by Black & Decker Service Centers or Authorized
Service Centers.

CHARGE THE BA TTERY (Figure1)

1. Attach charger cord to shear.

2. Plug charger into any 120-Volt receptacle. Your shear is now on charge.

CAUTION: This Charger can be used only with 60 cycle,

115-120 AC voltage.

3. Recharging the shear will require on the average about 16 hours for it to reach full capacity.
The shear will not overcharge and can be left on charge indefinitely throughout the cutting
season. One 7-hour charge will restore about 1/2 the battery capacity. A 4-hour charge will
give about 8-10 minutes of operation. Continuous charging may slightly shorten overall
battery life, but will not diminish the running time per charge.

SA VE THESE INSTRUCTIONS

OPERATION & INSTRUCTIONS

SWITCH

A SWITCH LOCKING BUTTON is provided on the top of the handle as a safety feature. Please note

the following very carefully.

1. Disconnect charger before attempting to turn switch “ON”.

2. TO TURN TOOL “ON” (FIGURE 2) slide the locking button “A” FORWARD with your thumb,
and hold it FORWARD momentarily, while you squeeze the trigger switch “B”. The trigger has
been designed so that it is very easy to hold in the “ON” position.

3. TO TURN TOOL “OFF”, merely release the trigger.

INSTRUCTION MANUAL

CCCCoooorrrrddddlllleeeessssssss GGGGrrrraaaassssssss SSSShhhheeeeaaaarr

rr

SAVE THIS MANUAL FOR FUTURE REFERERENCE.

KEY INFORMA TION YOU SHOULD KNOW:

•Charger may hum; tool or charger may become warm while charging.

•Charge batteries before initial use.

•Press lock-off button before pulling trigger.

Cat No. GS500 Form No. 243147-00 REV. 3 (DEC. ‘02)

Copyright © 2002 Black & Decker Printed in China

GS500

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG
Than Than
0 - 6 18 16 16 14
6- 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

FIG 1

3.6V3.6V

A

B

FIG 2

3.6V

FIG 3

FIG 4

3.6V3.6V

FIG 5

3

.6

V

3.6V

3.6V3.6V

AA

BB

FIG 6

BB

A

FIG 7

3

.6V3.6V

FIG 8

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986).

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION

AVAILABLE, CATALOG NO., TYPE NO., AND DATE CODE.

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE

YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR

COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

(544-6986)

RENSEIGNEMENTS IMPORTANTS

• Le chargeur peut émettre un bourdonnement; les piles ou le chargeur peuvent
devenir chauds au toucher pendant le chargement.

• Il faut charger les piles avant la première utilisation.

• Enfoncer le bouton de verrouillage avant d’appuyer sur la détente.ERTISSEMENT

AVERTISSEMENT : IMPORTANTES MESURES DE SÉCURITÉ

Afin de réduire les risques de blessures :

•Avant toute utilisation, s'assurer que tous ceux qui se servent de l'outil de jardinage lisent et
comprennent toutes les mesures de sécurité et tout autre renseignement contenu dans le présent guide.

• Conserver ces mesures et les relire fréquemment avant d'utiliser l'outil et d'en expliquer le
fonctionnement à d'autres personnes.

• AVERTISSEMENT : Afin de réduire les risques d'incendie, de secousses électriques ou de

blessures lorsqu'on utilise des outils de jardinage, il faut toujours respecter

les mesures de sécurité suivantes.

• AVERTISSEMENT : Le produit renferme des produits chimiques, dont du plomb. Selon l’état de

la Californie, ce produit chimique peut causer le cancer ainsi que des
malformations congénitales, et il présente d’autres dangers au système
reproductif humain. Se laver les mains après l’utilisation.

• AVERTISSEMENT : Le produit génère de la poussière qui peut renfermer des produits

chimiques. Selon l’état de la Californie, ces produits chimiques peuvent
causer le cancer ainsi que des malformations congénitales, et ils présentent
d’autres dangers au système reproductif humain. Voici des exemples de tels
produits chimiques :

• les composés d’engrais;

• les composés d’insecticides, d’herbicides et de pesticides;

• l’arsenic et le chrome provenant de bois traité.
Afin de minimiser les risques, porter de l’équipement de sécurité approuvé comme des masques
antipoussières spécialement conçu pour filtrer les particules microscopiques.

MISE EN GARDE : Porter un dispositif approprié de protection de l’ouïe lors de l’utilisation du

produit. Dans certaines conditions et durées d’utilisation, le produit peut
émettre un niveau de bruit provoquant la perte de l’ouïe.

LIRE TOUTES LES DIRECTIVES.

MESURES DE SÉCURITÉ POUR TOUS LES OUTILS

• TENIR COMPTE DU MILIEU DE TRAVAIL. Ne pas utiliser l'outil dans un endroit mouillé ou humide.

Protéger l'outil de la pluie.

• ÉLOIGNER LES ENFANTS. Tous les visiteurs doivent être tenus à l'écart de l'aire de travail.

• RANGER LES OUTILS INUTILISÉS À L'INTÉRIEUR. Il faut ranger les outils dans un endroit sec,

situé en hauteur ou fermé à clé, hors de la portée des enfants.

• NE JAMAIS FORCER L'OUTIL. Afin d'obtenir un rendement sûr et efficace, utiliser l'outil à son

rendement nominal.

• UTILISER L'OUTIL APPROPRIÉ. Se servir de l'outil selon l'usage prévu.

• PORTER DES VÊTEMENTS APPROPRIÉS. Éviter de porter des vêtements amples et des bijoux qui

peuvent être happés par les pièces en mouvement. Porter des gants de caoutchouc et des chaussures
à semelle antidérapante pour travailler à l'extérieur. Protéger la chevelure si elle est longue.

• NE PAS DÉPASSER SA PORTÉE. Toujours demeurer dans une position stable et garder son

équilibre.

• PORTER DES LUNETTES DE SÉCURITÉ ET AUTRE ÉQUIPEMENT DE SÉCURITÉ. Porter des lunettes

de protection ou de sécurité à écrans latéraux, conformément aux normes de sécurité
appropriées, et, au besoin, un écran facial. Porter également un masque respiratoire si le travail
de coupe produit de la poussière. La présente mesure vaut pour toute personne dans la zone de
travail. Il faut également porter un casque, des protège-tympans, des gants et des chaussures de
sécurité ainsi qu'utiliser des systèmes de dépoussiérage lorsque spécifié ou exigé. Les lunettes de
sécurité et autre matériel semblable sont vendus séparément chez les détaillants et dans les
centres de service Black & Decker.

• PRENDRE SOIN DES OUTILS. Conserver les outils propres et affûtés pour qu'ils donnent un

rendement supérieur et sûr. Suivre les directives concernant la lubrification et le remplacement
des accessoires. S'assurer que les poignées sont toujours propres, sèches et libres de toute tache
d'huile ou de graisse.

• ÉVITER LES DÉMARRAGES ACCIDENTELS. Ne pas laisser le doigt sur l'interrupteur lorsqu'on

transporte l'outil. S'assurer que l'interrupteur est à la position hors circuit lorsqu'on branche
l'outil.

• VÉRIFIER LES PIÈCES ENDOMMAGÉES. Avant d'utiliser de nouveau l'outil, bien vérifier un

protecteur endommagé ou toute autre pièce défectueuse afin de déterminer si elle fonctionnera
de façon appropriée et si elle remplira la fonction prévue. Vérifier l'alignement et les attaches
des pièces mobiles, le degré d'usure des pièces et leur montage, ainsi que tout autre facteur
susceptible de nuire au bon fonctionnement de l'outil. Faire réparer ou remplacer tout protecteur
ou toute autre pièce endommagée dans un centre de service autorisé, sauf si le présent guide fait
mention d'un avis contraire.

• DEMEURER VIGILANT. Travailler avec vigilance et faire preuve de bon sens. Ne pas se servir de

l'outil lorsqu'on est fatigué.

• RÉPARATIONS ET ENTRETIEN. Confier les réparations, l'entretien et les rajustements non spécifiés

dans le présent guide au personnel des centres de service Black & Decker n'utilisant que des
pièces de rechange identiques.

• UTILISATION D'AUTRES ACCESSOIRES. L'utilisation de tout accessoire non recommandé pour

l'outil peut être dangereuse.

• NE PAS SAISIR LES LAMES À DÉCOUVERT ni les arêtes tranchantes lorsqu'on prend l'outil ou

qu'on le tient.

• CORDONS DE RALLONGE. S'assurer que le cordon de rallonge est en bon état. Lorsqu'on se

sert d'un cordon de rallonge, s'assurer qu'il est de calibre approprié pour la tension nécessaire
au fonctionnement de l'outil.

Calibre minimal des cordons de rallonge

Tension Longueur totale du cordon en pieds
120 V 0-25 26-50 51-100 101-150

240 V 0-50 51-100 101-200 201-300
Intensité (A)

Au Au AWG
moins plus

0- 618161614
6- 1018 16 14 12
10 - 12 16161412
12 - 16 14 12 Non recommandé

MESURES IMPORTANTES RELATIVES AUX COUPE-HERBE

1. Éloigner les mains des lames.

2. Ne pas charger l'outil sous la pluie ni dans un endroit mouillé.

3. Ne pas se servir d'un outil alimenté par une pile sous la pluie.

TRIMMING CAP ACITY

Much depends upon the density of growth, type of grass, cleanliness and sharpness of blades, but
under average conditions the shear will cut for approximately 30 minutes without recharging.

TRIMMING INSTRUCTIONS (FIGURES 3, 4 AND 5)

1. Be sure that you have read carefully the safety rules. Use shear only for trimming grass and
weeds.

2. For the best results you should trim only on a dry day, but water or moisture in the grass or
on the ground does not create an electric shock hazard with this tool. Just be sure not to cut
through any electric cords which may be in the area.

3. Keep your other hand well away from the blade, and maintain a stable working position so
that you don’t slip. Don’t overreach.

4. Feed the blade into the grass at a rate that allows it to keep up cutting speed. Feed slower if
the blade slows down. Watch out for foreign objects in the grass.

MAINTENANCE

It is easy to remove sap and dirt deposits when they are fresh and moist, but difficult after they
become dry. Therefore, it is recommended that you wash the blades in water after each use. Hold
the BLADES under a running faucet (Figure 6a) or in a pan of water (Figure 6b) and turn the tool
“ON” to help dislodge the deposits. (There is no electric shock hazard from the shear’s low-voltage
power supply .) If the buildup of sap is difficult to remove, it may be necessary (with the motor
“OFF”) to scrub the blades with soap and a stiff bristle brush.

After cleaning, wipe the blades with a cloth and allow them to dry. Then, with a rag, apply a thin
film of light engine oil to the top and bottom of the blades. Do not over oil. T urn the shear “ON”for
a few seconds to work the lubricant between the blades.

BLADE REPLACEMENT

Under normal usage and proper cleaning, shear blades should last approximately one season.
When blades become worn and will not cut, they must be replaced. During the overall life of the
shear , blades should be replaced before each cutting season. Sharp blades help to maintain
consistent cutting time. Blades are available, at extra cost, at your local Black & Decker Service
Center .( RB-001)

TO REPLACE THE BLADES:

Remove three screws from bottom of shear (Figure 7a). Lift worn blades off. Be sure washer
remains on its post on the gear (Figure 7b). Clean out any grass or dirt. The teeth on the new
blades should be evenly spaced—shift the moving blade, if necessary to accomplish this. Move
gear to line up washer with slot in moving blade (Figure 7b). Slot in moving blade must fit over
washer when blade is placed on shear . Replace three screws to fasten blades to shear.

•LUBRICATION

No periodic relubrication of the bearings or mechanism is required.

•CLEANING PLASTIC P ARTS

Use only warm water and mild soap to clean the plastic parts. Many household cleaners contain
chemicals which could seriously damage the plastic. Never use gasoline, turpentine, lacquer or
paint thinner , dry cleaning fluids, or similar products.

•STORAGE

The best storage place is one that is cool and dry. Store the tool away from direct sunlight, heating
pipes and ducts, furnaces, etc. The best storage temperature is about +50°F. Do not store where
temperatures go below +40°F or above 120°F. Avoid storage in outside metal buildings where
temperature can exceed 120°F in summer .

For off-season storage you should first recharge the shear for 16 hours. Unplug the charger from
the wall socket and then disconnect charger from the shear . (Fig. 1) Clean and lightly oil the blades
as described in this manual and store the shear and charger away .

•BLADE NICKS

The blades are made from high quality , heat treated steel and they will hold a sharp edge for a
long period of time. However , if you accidentally hit a wire fence, stones, glass or other hard
objects, you may put a nick in the blade. There is no need to remove this nick as long as it does not
interfere with the movement of the blade. If it does interfere, use a fine toothed file or sharpening
stone to remove it. A replacement blade set is available from your Black & Decker service center
when blades become worn.

•DROPPING THE GRASS SHEAR

If you drop the shear , carefully inspect it for damage, if the blades are bent, replace them with a
new set of blades from your dealer . If the housing is cracked, or handle broken, contact your local
Black & Decker Service Center for repairs before putting the tool back into use.

•BATTERIES

When they reach the end of their useful life, the batteries in your tool will no longer accept a
charge. Before discarding the old tool, the nickel cadmium batteries must be removed and recycled
or disposed of properly . Cadmium is a highly toxic form of waste and is extremely harmful to the
environment. Contact your local municipality to find out how to properly recycle or dispose of the
batteries. Alternately, you can take or send the complete tool to your local Black & Decker service
center . If battery replacement is required they will, at your direction, replace the batteries and
properly recycle or dispose of the old ones. If you choose to replace the tool at this time, they will
be glad to take the old one and see to its proper recycling or disposal.

IMPORTANT:To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
should be performed by Black & Decker Service Centers or other qualified service organizations,
always using identical replacement parts.

Accessories: GSH500 Extension Handle Kit (fig. 8)

RB-001 Grass Shear Replacement Blade

NOTE! - Accessories sold separately

• WARNING: Only use Shear with Black & Decker approved accessories. Use of non approved

Accessories could be hazardous.

Service Information

Black & Decker offers a full network of company-owned and Authorized Service locations
throughout North America. All Black & Decker Service Centers are staffed with trained personnel
to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair , or genuine factory replacement parts, contact the Black
& Decker service location nearest you.

To find your local service location, refer to the yellow page directory under “Tools—Electric” or call:

1-800-54-HOW-TO.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or
workmanship. The defective product will be replaced or repaired at no charge in either of two
ways:

The first, which will result in exchanges only , is to return the product to the retailer from whom it
was purchased (provided that the store is a participating retailer). Returns should be made within
the time period of the retailer’ s policy for exchanges (usually 30 to 90 days after the sale). Proof of
purchase may be required. Please check with the retailer for their specific return policy regarding
returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or
Authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and Authorized Service Centers are listed under “Tools-Electric”
in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you
may have other rights which vary from state to state. Should you have any questions, contact the
manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

GUIDE D’UTILISATION

Modèle GS500

CCCCoooouuuuppppeeee----hhhheeeerrrrbbbbeeee ssssaaaannnnssss ffffiiiill

ll

AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAISON

PRIÈRE DE COMPOSER

1 800 544-6986