Black & Decker GH610 TYPE 1 Owner’s Manual

TRIMMER / EDGER

iNSTRUCTiON MANUAL

Model Number GH610

PLEASE READ BEFORE RETURNING

THIS PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your

Black & Decker purchase, go to

WWW.BLACKANDDECKER.COM/INSTANTANSWERS

for instant answers 24 hours a day.

If you can't find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri

to speak with an agent.

Please have the catalog number available when you call.

SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPANOL EN LA CONTRAPORTADA.
POUR LE FRAN(_AIS, VOIR LA COUVERTURE ARRIERE.

IN.STRUCTIVO DE O.PERACION, CENTROS DE SERVICIO Y
POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Model No. GH610

KEY INFORMATION YOU SHOULD KNOW:

o The guard must be installed before trimming or edging - if

not, the motor will overheat (page 5).

o When replacing the line, use only .065 inch diameter

ROUND line (B&D Model No. AF-100 is recommended) -
otherwise the tool will not function properly (page 8).

o Do not bump the feed head against the ground - it will

disrupt the feed mechanism.

o Always use the cord retention feature (page 7).

SafetyGuidelines-Definitions.................................................2

ImportantSafetyWarningsandInstructions............................2

SafetyWarningsandInstructions:PolarizedPlugs.................4

SafetyWarningsandInstructions:ExtensionCords................4

Components.............................................................................5

Assembly/ Adjustment ............................................................ 5

Operating Instructions .............................................................. 7

Replacement Accessories ....................................................... 8

Maintenance ............................................................................ 10

Troubleshooting ....................................................................... 10

Service Information .................................................................. 11

Full Two-Year Home Use Warranty .......................................... 11

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The
information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.

z_DANGER: Indicates an imminently hazardous situation which

if not avoided, will result in death or serious injury.

z_WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

Z_CAUTION: Indicates a potentially hazardous situation which,

not avoided, may result in minor or moderate injury.

NOTICE: Used without the safety alert symbol indicates a

potentially hazardous situation which, if not avoided, may result in
property damage.

Z_WARNING: When using electric gardening appliances, basic

safety precautions should always be followed to reduce risk of fire,
electric shock, and personal injury, including the following.

Read All Instructions

• ALWAYS WEAR EYE PROTECTION - Wear safety spectacles

or goggles at all times when this tool is plugged in.

• GUARD - Do not use this tool without guard attached.

• DRESS PROPERLY - Do not wear loose clothing or jewelry.

They can be caught in moving parts. Rubber gloves and
substantial rubber soled footwear are recommended when

working outdoors. Don't operate the tool when barefoot or
wearing open sandals. Wear long pants to protect your legs.
Wear protective hair covering to contain long hair.

• NYLON LINE - Keep face, hands and feet clear of rotating nylon
line at all times.

• THE ROTATING LINE PERFORMS A CUTTING FUNCTION -
Use care when trimming around screens and desirable plantings.

• KEEP ALL BYSTANDERS AWAY - at a safe distance from

work area, especially children.

• IMPORTANT WARNING - When being used as an Edger,

stones, pieces of metal and other objects can be thrown out at

high speed by the line. The toot and guard are designed to
reduce the danger. However, the following special precautions

should be taken:

• MAKE SURE that other persons and pets are at least 100 feet
(30m) away.

• TO REDUCE THE RISK of rebound (ricochet) injury, work going

away from any nearby solid object such as wall, steps, large
stone, tree, etc. Use great care when working close to solid
objects and where necessary, do edging or trimming by hand.

•AVOID ACCIDENTALLY STARTING - Don't carry plugged-in

toot with finger on trigger.

• DO NOT FORCE THE TOOL - at a rate faster than the rate at
which it is able to cut effectively.

• USE THE RIGHT TOOL- Do not use this toot for any job except
that for which it is intended.

• DON'T OVERREACH - Keep proper footing and balance at all times.

• DON'T ABUSE CORD - Don't yank cord from power supply.
Keep cord from heat, oil, and sharp edges.

• DAMAGE TO UNIT - If you strike or become entangled with a
foreign object, stop tool immediately, unplug, check for damage
and have any damage repaired before further operation is
attempted. Do not operate with a broken hub or spool.

• DAMAGE TO CORD - Keep power cord away from rotating
line. If you damage the cord, unplug it from the power supply
before moving the tool or examining the damage. A damaged
cord must be replaced before further use.

• DISCONNECT TOOL - when not in use, when replacing line, or
prior to cleaning.

• AVOID DANGEROUS ENVIRONMENTAL CONDITIONS - Do
not use electric tools in damp or wet locations. Follow all

instructions in this Instruction Manual for proper operation of your
tool. Don't use the tool in the rain.

• DO NOT OPERATE portable electric tools in gaseous or
explosive atmospheres. Motors in these tools normally spark, and
the sparks might ignite fumes.

• STORE IDLE TOOLS INDOORS - When not in use, tools
should be stored indoors in a dry, locked-up place out of reach of

children.

• GROUND FAULT CIRCUIT INTERRUPTER (GFC0 protection
should be provided on the circuits or outlets to be used for the
gardening appliance. Receptacles are available having built in
GFCI protection and may be used for this measure of protection.

• SECURE EXTENSION CORD using the cord retainer shown in
Figure 7.

• STAY ALERT - Watch what you are doing. Use common sense.
Do not operate tool when you are tired.

• MAINTAIN APPLIANCES WITH CARE - Follow instructions in

maintenance section. Inspect extension cords periodically and

replace if damaged. Keep handles dry, clean and free from oil and
grease.

• CHECK DAMAGED PARTS - Before further use of the

appliance, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and

perform its intended function. Check for alignment of moving

parts, binding of moving parts, breakage of parts, mounting, and

any other condition that may affect its operation. A guard or other

part that is damaged should be properly repaired or replaced by

an authorized service center unless otherwise indicated
elsewhere in this manual.

zLWARNING: When servicing double insulated tools, USE

ONLY IDENTICAL REPLACEMENT PARTS. Replace or repair
damaged cords.

ZLWARNING: To prevent electrical shock hazard, use only with

an extension cord suitable for outdoor use. Always connect extension
cords to a fused line or one protected by a circuit breaker.

• DO NOT immerse toot in water or squirt it with a hose. DO NOT

allow any liquid to get inside it.

• DO NOT store the toot on or adjacent to fertilizers or chemicals.

• DO NOT clean with a pressure washer.

SAVE THESE INSTRUCTIONS

The label on your tool may include the following symbols. The
symbols and their definitions are as follows:

V .............. volts

Hz ............ hertz

min ............ minutes

- - -. ......... direct current

[] .............. Class II Construction

z_ ............safety alert symbol

A ................ amperes

W................ watts

"_ .............. alternating current

no .............. no load speed

............ earthing terminal

.../min ...... revolutions or

reciprocations per minute

Z_WARNING: Some dust created by this product contains

chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some e×amples of these

chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber
To reduce your exposure to these chemicals, wear approved safety
equipment such as dust masks that are specially designed to filter
out microscopic particles.

Make sure your extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating. The table
shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord. If the

extension will be used outside, the cord must be suitable for outdoor
work. The letters "WA" on the cord jacket indicate that the cord is

suitable for outdoor use.

To reduce the risk of electric shock, this equipment has a polarized
plug (one blade is wider than the other) and will require the use of a
polarized extension cord. The appliance plug will fit into a polarized
extension cord only one way. If the plug does not fit fully into the
extension cord, reverse the plug. If the plug still does not fit, obtain
a correct polarized extension cord. A polarized extension cord will
require the use of a polarized wall outlet. This plug will fit into the
polarized wall outlet only one way. If the plug does not fit fully into
the wall outlet, reverse the plug. If the plug still does not fit, contact
a qualified electrician to install the proper wall outlet. Do not change
the equipment plug, extension cord receptacle, or extension cord
plug in any way.

Volts Total Length of Cord in Feet

Minimum Gauge for Cord Sets

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m)(30,4-60,9m)(60,9-91,4m)

Ampere Rating

More Not more American Wire Gauge

Than Than
0 6 18 16 16 14
6 10 18 16 14 12

10 12 16 16 14 12
12 16 14 12 Not Recommended

1. Switch

2. Cord Retainer

3. Cord Receptacle

4. Auxiliary Handle

5. Cotiar (to adjust
height and edge)

6. Motor Housing

7. Edge Guide

8. Guard

9. Spool

ASSEMBLY TOOLS REQUIRED (NOT SUPPLIED):

- Phillips Screwdriver
INSTALLING THE GUARD

z_WARNJNG: UNPLUG THE TOOL BEFORE ATTEMPTING TO

ATTACH THE GUARD, EDGE GUIDE OR HANDLE. NEVER

OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE. THE
GUARD MUST ALWAYS BE ON THE TOOL TO PROTECT THE
USER.

• Turn the trimmer upside
down so that you are booking
down at the spool cap (a).

• Turn the guard (b) upside
down and slide it onto the

motor housing (c). Make
sure the tabs (d) on the

guard engage the ribs (e) on

/ //

J_

JH

JH

the motor housing as shown.

• Continue to slide the guard
on until you hear it "snap" into
place.

• Using a phillips
screwdriver, remove the

screw from the guard.

• Insert the guard screw as
shown in figure 2 to
complete the guard
assembly.

• Once the guard is installed,
remove the covering from the

line cut-off blade, located on
the edge of the guard.

ATTACHING THE AUXILIARY HANDLE

• To attach the handle, press
in on the buttons (f) on both
sides of the upper housing as
shown in figure 3.

• Position the handle as
shown in figure 4 (with the

Black & Decker logo facing
upward). Partially push the

handle on so that it will hold
the buttons in when you

release them with your hand.

• Push the handle
completely onto the housing

and position it slightly until it
"snaps" into place (figure 5).

• To adjust the handle up or
down, press in on the button
(g) and raise or lower the

handle.

• The handle should be
adjusted so that your front

arm is straight when the
trimmer is in the working
position.

HEIGHT ADJUSTMENT

• The overall height of the
trimmer can be adjusted by

loosening the collar (h) and
rotating it in the direction of

the arrow shown in figure 6.

• Move the upper housing
straight up or down. When
the desired height is
achieved, tighten the collar
by rotating it opposite of the
direction shown in figure 6.

O

ATTACHING EXTENSION CORD

• An extension cord retainer
(figure 7) is built into the switch

handle that prevents the cord
from coming unplugged. To use
this feature, simply double the

extension cord about 8 inches
(203mm) from the end, and

insert it into the slot (i) in the end
of the handle area. Hook the

loop formed by doubling the
cord over the tab (j). Gently tug

on the cord to insure that it is
firmly retained in the trimmer's

handle. Plug the receptacle end of the extension cord into the
plug blades (k) in the trimmer.

SWITCHING ON AND OFF

• To switch the tool on, squeeze the trigger
lever.

• To switch the tool off, release the trigger
lever.

• With the unit on, angle unit and slowly
swing the trimmer side to side as shown in
figure 8.

CONVERT TO EDGING MODE

"%1

ZLWARNING: Always use proper eye protection that conforms

to ANSI Z87.1 (CAN/CSA Z94.3) while operating this power tool.

ZLCAUTION: Inspect area to be trimmed and remove any wire,

cord, or string-like objects which could become entangled in the

rotating line or spool. Be particularly careful to avoid any wire which
might be bent outwardly into the path of the tool, such as barbs at the

base of a chain link fence.

• To operate as a maintenance edger, turn _Jl
the collar (I) as shown in part 1 of figure 9.

• Hold the metal shaft and rotate the lower
housing 180° as shown in part 2.

• Turn the collar (t) until tight.

•Ifdesired,pullthewireedgeguide(m)
outfromthemotorhousinguntilitclicks
intothelockedpositionasshowninfigure
10andpositionthetrimmerabovethe
surfaceasshowninfigure10.

•Returntothetrimmingpositionby
looseningthelockcollarandrotatingthe
lowerhousingback180°.Thetootwiltlock
inthetrimmerposition.Whenusingthe
tool,retractthewireedge
guidetotheoriginalposition,
outoftheway.

CUTTING LINE/LiNE FEEDING

Your trimmer uses .065 inch (1.65 mm) diameter, ROUND
nylon line. During use, the tips of the nylon lines will become
frayed and worn and the special self feeding spool will
automatically feed and trim a fresh length of line. Cutting line will
wear faster and require more feeding if the cutting or edging is
done along sidewalks or other abrasive surfaces or heavier
weeds are being cut. The advanced automatic line feeding
mechanism senses when more cutting line is needed and feeds
and trims the correct length of line whenever it's required. DO
NOT BUMP unit on ground in attempt to feed line or for any other
purposes.

UseBlack&DeckerreplacementspoolModelNo.AF-100.
Reloadnylonline(eitherbulkorprewoundreplacementspool)as

showninthismanual.

•USEONLY.065 inch (1.65 mm) DIAMETER ROUND NYLON

LINE. Do not use serrated or heavier gauge line, as they will
overload the motor and cause overheating. This line is available
at your local dealer or authorized service center.

• Other replacement parts (guards, spool caps, etc.) are available
through Black & Decker service centers. To find your local service

location call: 1-800=544-6986 or visit www.biackanddecker.com.

ZLWARNIN6: The use of any accessory not recommended by

Black & Decker for use with this tool could be hazardous.

REPLACING THE SPOOL (FIGURES 11,12,13)

• Unplug toot.

• Depress the tabs (n) and
remove the spool cap (o)

from the spool housing (p) in
the trimmer head (figure 11).

• For best results, replace
spool with Black & Decker

model no. AF-100.

• Grasp empty spool with one
hand and spool housing with
other hand and pull spool

out.

Replacement

spool

•Iflever(q)(figure12)in
baseofhousingbecomes
dislodged,replaceincorrect
positionbeforeinsertingnew
spoolintohousing.

•Removeanydirtandgrass
fromthespoolandhousing.

•Unfastentheendofthe
cuttinglineandguidetheline

intotheeyelet(r)figure13.

•Takethenewspooland
pushitontotheboss(s)

(figure12)inthehousing.
Rotatethespoolslightlyuntilit

isseated.

Thelineshouldprotrude
approximately5-3/8inches

(136mm)fromthehousing.

•Alignthetabsonthespool
capwiththeslots(t)inthe

housing(figure13).

•Pushthecapontothe

housinguntilitsnaps

securelyintoplace.

NOTICE: To avoid tool damage, if the cutting line protrudes

beyond the trimming blade, cut it off so that it just reaches the
blade.

REWINDING SPOOL FROM BULK LINE

(USE ONLY .065 IN. ROUND DIAMETER LINE) (FIGURES 14, 15, 16)
Bulk line is also available for purchase from your local retailer.

NOTE: Hand wound spools from bulk line are likely to become
tangled more frequently than Black & Decker factory wound
spools. For best results, factory wound spools are

recommended.

To install bulk line, follow the steps below:

• Unplug toot.

• Remove the empty spool
from the tool as described

in "REPLACING THE
SPOOL".

• Remove any remaining
cutting line from the spool.

• Make a fold at the end of
the cutting line at about 3/4

inch (19mm)(u). Feed the
cutting line into one of the
line anchoring slots (v) as
shown in figure 14.

• Insert the 3/4 inch (19mm)
end of the bulk line into the

hole (w) in the spool
adjacent to the slot as
shown in figure 15.

•Windthecuttinglineontothespoolin
thedirectionofthearrowonthespool.
Makesuretowindthelineonneatlyand
inlayers.Donotcrisscross(figure16).

•Whenthewoundcuttinglinereaches
therecesses(x),cuttheline.(figure15).

•Fitthespoolontothetoolasdescribed

in"REPLACINGTHE SPOOL".

ZLCAUTION: Before you begin

trimming, only use the appropriate type of
cutting line.

X

ZLWARNING: To avoid serious injury, switch off and unplug the

tool before performing any maintenance.

1. Keep the air intake slots clean to avoid overheating.

2. Your trimmer line can dry out over time. To keep your line in top
condition, store spare pre-wound spools or bulk line in a plastic,
sealable bag with a tablespoon of water.

3. Plastic parts may be cleaned by using a mild soap and a damp
rag.

4. The line cutter on the edge of the guard can dull over time. It is
recommended you periodically touch-up the sharpness of the

blade with a file.

IMPORTANT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed by
authorized service centers or other qualified service organizations,
always using identical replacement parts.

TOOL RUNS SLOWLY

• Check that the spool housing can rotate freely. Carefully clean it if
necessary.

• Check that the cutting line does not protrude more than
approximately 5-3/8 inches (136mm) from the spool. If it does, cut
it off so that it just reaches the line trimming blade.

AUTOMATIC LINE FEED DOES NOT WORK

• Keep the tabs depressed and remove the spool from the spool
housing in the trimmer head.

• Pull the cutting line until it protrudes approximately 5-3/8 inches
(136mm) from the spool. If insufficient cutting line is left on the
spool, install a new spool of cutting line.

• Ensure that the line is not crisscrossed on the spool as detailed
in figure 16. If it is, unwind the cutting line, then wind it back on
the spool neatly so that the lines do not cross.

• Align the tabs on the spool cap with the cut outs in the housing.

• Push the spool cap onto the housing until it snaps securely into
place.

• If the cutting line protrudes beyond the trimming blade, cut it off
so that it just reaches the blade. If the automatic line feed still
does not work or the spool is jammed, try the following
suggestions:

• Carefully clean the spool and housing.

• Remove the spool and check if the lever in the spool housing
can move freely.

• Remove the spool and unwind the cutting line, then wind it on
neatly again. Replace the spool into the housing.

10

All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool

service. Whether you need technical advice, repair, or genuine
factory replacement parts, contact the Black & Decker location

nearest you. Tofind your local service location, refer to the yellow

page directory under "Tools--Electric" or call: 1-800-544-6986 or

visit www.blackanddecker.com

Black & Decker (U.S.) Inc. warrants this product for two years
against any defects in material or workmanship. The defective
product will be replaced or repaired at no charge in either of two
ways.

The first is to return the product to the retailer from whom it was
purchased (provided that the store is a participating retailer).

Returns should be made within the time period of the retailer's
policy for exchanges (usually 30 to 90 days

after the sate). Proof of purchase may be required. Please check
with the retailer for their specific return policy regarding returns that
are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a

Black & Decker owned or authorized Service Center for repair or

replacement at our option. Proof of purchase may be required.

Black & Decker owned and authorized Service Centers are listed
under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives

you specific legal rights and you may have other rights which vary
from state to state or province to province. Should you have any
questions, contact the manager of your nearest Black & Decker
Service Center. This product is not intended for commercial use.

LATIN AMERICA: This warranty does not apply to products sold in
Latin America. For products sold in Latin America, check country
specific warranty information contained in the packaging, call the
local company or see the website for warranty information.

FREE WARNING LABEL REPLACEMENT: Ifyour warning labels
become illegible or are missing, call 1-800-544-6986 for a free
replacement.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

11

See 'Tools=Electric'

- Yellow Pages -

for Service & Sales

TAILLE-BORDURE / COUPE-

BORDURE MODE D'EMPLOI

Numero de modele GH610

A LIRE AVANT DE RETOURNER CE PRODUIT

POUR QUELQUE RAISON QUE CE SOIT •

Sidesquestions0udespr0blemessurgissentapresrachatd'unpr0duit

Black&Decker,consulterlesiteWeb

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

pourobtenirdesr@onsesinstantanement24heuresparjour.

Silareponseestintrouvableouenrabsenced'acces_.I'lntemet,

composerle1-800-544-6986de8ha.17hHNE,dulundiauvendredi,

pourparleravecunagent.

Priered'avoirlenumerodecataloguesouslamainIorsderappel.

12

Numero de modele GH610

VOlCl DES RENSEIGNEIVlENTS IMPORTANTS

QU'iL VOUS FAUT CONNAITRE :

o Le pare-main doit _tre installe avant de debuter le taillage

ou la coupe sinon le moteur surchauffera (page 17).

o Utiliser seulement un fil ROND de 1,7 mm (0,065 po) de

diametre Iors du remplacement (modele AF-100 de B&D

recommande), sinon I'appareil ne fonctionnera pas

correctement (page 19).

o Eviter de frapper la t_te d'alimentation contre le sol. En

effet, cela endommagera le mecanisme d'alimentation.

• Toujours utiliser le dispositif de retenue du cordon (page 18).