Black & Decker GH1100, GH2000 User Manual

GGGGHHHH1111000000000000,,,, GGGGHHHH1111111100000000,,,, GGGGHHHH2222000000000000 TTTTRRRRIIIIMMMMMMMMEEEERRRR////EEEEDDDDGGGGEEEERR

RR

IINNSSTTRRUUCCTTIIOONN MMAANNUUAALL

Date Code:

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PLEASE READ BEFORE RETURNING THIS

PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your Black & Decker purchase, go to

HHTTTTPP::////WWWWWW..BBLLAACCKKAANNDDDDEECCKKEERR..CCOOMM//IINNSSTTAANNTTAANNSSWWEERRS

for instant answers 24 hours a day.

If you can’t find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.

Please have the catalog number available when you call.

KEY INFORMATION YOU SHOULD KNOW:

• The guard must be installed before trimming or edging - if not, the motor
will overheat.

• When replacing the line, use only .080 inch diameter ROUND line - other­wise the unit will not function properly.
Do not bump the feed head against the ground - it will disrupt the feed

•
mechanism.

• Angle tool slightly (5

• Always use the cord retainer and the extension cord lock feature.

• For trouble free feeding and best results, only use Black & Decker
replacement spools with dual 0.080 inch line. Black & Decker
replacement spool model number DF-080.

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

Cat No. GH1000, GH1100, GH2000 Form No. 90579142 August 2011
Copyright © 2011 Black & Decker Printed in China

WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this tool reads and understands all safety

instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

CAUTION: Failure to comply with the recommendations outlined in the key information

section will void warranty.

WARNING: When using electric gardening appliances, basic safety precautions should

always be followed to reduce risk of fire, electric shock, and personal injury, including the
following:

WARNING: Some dust created by this product contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are: • compounds in fertilizers

To reduce your exposure to these chemicals, wear approved safety equipment such as
dust masks that are specially designed to filter out microscopic particles.

WARNING: This product contains chemicals, including lead, known to the State of
California to cause cancer, and birth defects or other reproductive harm. Wash hands
after handling.

CAUTION: Wear appropriate personal hearing protection during use. Under some
conditions and duration of use, noise from this product may contribute to hearing loss.

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual.
The information it contains relates to protecting YOUR SAFETY and PREVENTING
PROBLEMS. The symbols below are used to help you recognize this information.

° to 10°) when trimming.

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber

Catalog Number: GH1000

GH1100

GH2000

S

• IMPORTANT WARNING – When being used as an Edger, stones, pieces of metal and

other objects can be thrown out at high speed by the line. The tool and guard are
designed to reduce the danger. However, the following special precautions should be taken:

• MAKE SURE that other persons and pets are at least 100 feet (30m) away.

• TO REDUCE THE RISK of rebound (ricochet) injury, work going away from any nearby

solid object such as wall, steps, large stone, tree, etc. Use great care when working close
to solid objects and where necessary, do edging or trimming by hand.

• AVOID ACCIDENTALLY STARTING – Donʼt carry plugged-in tool with finger on trigger.

• DO NOT FORCE THE TOOL – at a rate faster than the rate at which it is able to cut

effectively.

• USE THE RIGHT TOOL – Do not use this tool for any job except that for which it is intended.

• DONʼT OVERREACH – Keep proper footing and balance at all times.

• DONʼT ABUSE CORD – Donʼt yank cord from power supply. Keep cord from heat, oil,

and sharp edges.

• DAMAGE TO UNIT – If you strike or become entangled with a foreign object, stop tool

immediately, unplug, check for damage and have any damage repaired before further
operation is attempted. Do not operate with a broken hub or spool.

• DAMAGE TO CORD – Keep power cord away from rotating line. If you damage the cord,

unplug it from the power supply before moving the tool or examining the damage. A
damaged cord must be replaced before further use.

• DISCONNECT TOOL – when not in use, when replacing line, or prior to cleaning.

• AVOID DANGEROUS ENVIRONMENTAL CONDITIONS – Do not use electric tools in

damp or wet locations. Follow all instructions in this Instruction Manual for proper
operation of your tool. Donʼt use the tool in the rain.

• DO NOT OPERATE portable electric tools in gaseous or explosive atmospheres. Motors

in these tools normally spark, and the sparks might ignite fumes.

• STORE IDLE TOOLS INDOORS – When not in use, tools should be stored indoors in a

dry, locked-up place out of reach of children.

• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the

circuits or outlets to be used for the gardening appliance. Receptacles are available
having built in GFCI protection and may be used for this measure of protection.

• SECURE EXTENSION CORD using the cord retainer shown in Figure 3.

• STAY ALERT – Watch what you are doing. Use common sense. Do not operate tool

when you are tired.

• MAINTAIN APPLIANCES WITH CARE – Follow instructions in maintenance section.

Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and
free from oil and grease.

CHECK DAMAGED PARTS – Before further use of the appliance, a guard or other part

•
hat is damaged should be carefully checked to determine that it will operate properly and

t

erform its intended function. Check for alignment of moving parts, binding of moving

p

arts, breakage of parts, mounting, and any other condition that may affect its operation.

p

guard or other part that is damaged should be properly repaired or replaced by an

A

uthorized service center unless otherwise indicated elsewhere in this manual.

a

WARNING: When servicing double insulated tools, USE ONLY IDENTICAL

REPLACEMENT PARTS. Replace or repair damaged cords.

WARNING: To prevent electrical shock hazard, use only with an extension cord

suitable for outdoor use. Always connect extension cords to a fused line or one protected
by a circuit breaker.

ADDITIONAL WARNINGS FOR STRING TRIMMERS

1. Keep the air intake slots (Figure 14) clean to avoid overheating.

2. Your trimmer line can dry out over time. To keep your line in top condition, store spare
pre-wound spools or bulk line in a plastic, sealable bag with a tablespoon of water.

3. Plastic parts may be cleaned by using a mild soap and a damp rag.

4. DO NOT immerse tool in water or squirt it with a hose. DO NOT allow any liquid to get
inside it.

5. Do not store the tool on or adjacent to fertilizers or chemicals.

6. DO NOT clean with a pressure washer.

7. The line cutter on the edge of the guard can dull over time.

SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider
than the other) and will require the use of a polarized extension cord. The appliance plug
will fit into a polarized extension cord only one way. If the plug does not fit fully into the
extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized
extension cord. A polarized extension cord will require the use of a polarized wall outlet.
This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into
the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to
install the proper wall outlet. Do not change the equipment plug, extension cord receptacle,
or extension cord plug in any way.

1

3

2

4

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may result

in minor or mod er ate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation

which, if not avoided, may result in property damage.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS

• ALWAYS WEAR EYE PROTECTION – Wear safety spectacles or goggles at all times

when this tool is plugged in.

• GUARD – Do not use this tool without guard attached.

• DRESS PROPERLY – Do not wear loose clothing or jewelry. They can be caught in

moving parts. Rubber gloves and substantial rubber soled footwear are recommended
when working outdoors. Donʼt operate the tool when barefoot or wearing open sandals.
Wear long pants to protect your legs. Wear protective hair covering to contain long hair.

• NYLON LINE – Keep face, hands and feet clear of rotating nylon line at all times.

• THE ROTATING LINE PERFORMS A CUTTING FUNCTION – Use care when trimming

around screens and desirable plantings.

• KEEP ALL BY-STANDERS AWAY – at a safe distance from work area, especially children.

5

6

1

13

7

9

1

8

10

1

2

14

Cutting line will wear faster and require more feeding if the cutting or edging is done
along sidewalks or other abrasive surfaces or heavier weeds are being cut. The
advanced automatic line feeding mechanism senses when more cutting line is needed
and feeds and trims the correct length of line whenever its required. DO NOT BUMP unit
on ground in attempt to feed line or for any other purposes.

CLEARING JAMS AND TANGLED LINES

From time to time, especially when cutting thick or stalky weeds, the line feeding hub
may become clogged with sap or other material and the line will become jammed as a
result. To clear the jam, follow the steps listed below.

1. Unplug the trimmer.

2. Press the release tabs on the line hub cap, as shown in Figure 9 and remove the cap by

pulling it straight off.

3. Pull the nylon line spool out and clear any broken line or cutting debris from the spool area.
(YOU DO NOT HAVE TO REMOVE THE CENTER SCREW TO REMOVE THE SPOOL).

4. Place spool and line into spool housing with lines “parked” in slots provided as shown in
figure 10.

5. Insert the line end through the appropriate holes in the spool hub. Pull slack line through
until it pulls out of the holding slots as shown in Figure 11.

6. Press the spool down GENTLY and rotate it until you feel it drop into place and then push
to snap into place. (When in place, the spool will turn a few degrees left and right freely).
Take care to keep the line from becoming trapped under the spool.

7. Snap the hub cap back on as shown in figure 12 by depressing lugs and pressing into
spool housing. NOTE: Make sure that cover is fully positioned, listen for two audible
clicks to ensure both lugs are correctly located. Power the tool on. In a few seconds or
less youʼll hear the nylon line being cut automatically to the proper length.

SPOOL OR LINE REPLACEMENT (Use .080 in. diameter ROUND line only)

1. Unplug the trimmer. Press the release tabs on the line hub cap, as shown in Figure 9
and remove the cap by pulling it straight off.

2. Remove the spool from the tool and remove and discard all line on the spool.

3. Choose either OPTION 1 or OPTION 2.

OPTION 1: ACCESSORY REPLACEMENT SPOOL

Use Black & Decker replacement spool Model No. DF-080. Install following instructions
under “ SPOOL OR LINE REPLACEMENT“ #1 through #6, discarding old spool for Step 3
and using new spool in subsequent steps.

PTION 2: REWINDING SPOOL USING BULK LINE

O

ulk line for your trimmer/edger is available at extra cost from your local dealer or

B

lack & Decker Service Center. Install following instructions under “SPOOL OR LINE

B

EPLACEMENT” #1 through #6, performing the following steps for Step 3.

R

Use .080 in. diameter ROUND line only)

(

a. Your line spool for this product has two (2) wind areas for line. Wind line in one area first
and then in the other. NOTE: For best results, wind line onto the outer portion of the spool
(side with arrows) first.

b. Fold over nylon line about 3/4 in. (19mm) from the end to form a “hook” as shown in
Figure 13. Insert the hooked end of the line into the slot on the inside of the spool.
c. Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on the
spool until the line builds up to the notches in the spool rim. Do not overfill spool. Repeat
for the other wind area.

4. Place spool and line into spool housing with lines “parked” in slots provided as shown in
figure 10.

5. Insert the line ends through the holes in the spool hub. Pull slack line through until it
pulls out of the holding slots as shown in Figure 11.

6. Press the spool down GENTLY and rotate it until you feel it drop into place and then push
to snap into place. (When in place, the spool will turn a few degrees left and right freely).
Take care to keep the line from becoming trapped under the spool.

7. Snap the hub cap back on as shown in figure 12, by depressing lugs and pressing into
spool housing. NOTE: Make sure that cover is fully positioned, listen for two audible
clicks to ensure both lugs are correctly located. Power the tool on. In a few seconds or
less youʼll hear the nylon line being cut automatically to the proper length.

• For trouble free feeding and best results, only use Black & Decker replacement

spools with dual 0.080 inch line. Black & Decker replacement spool model number
DF-080.

SAFETY WARNINGS AND INSTRUCTIONS: EXTENSION CORDS

Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. The table shows the
correct size to use depending on cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number, the heavier the cord. If the
extension will be used outside, the cord must be suitable for outdoor work. The letters “WA”
on the cord jacket indicate that the cord is suitable for outdoor use.

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gauge
Than Than
0-6 18 16 16 14
6-10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

Minimum Gauge for Cord Sets

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

SAVE THESE INSTRUCTIONS

ASSEMBLY / ADJUSTMENT SET-UP

WARNING: The guard must always be on the tool to protect the user.

NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.
UNPLUG THE TOOL BEFORE ATTEMPTING TO ATTACH THE GUARD.

1. Position the open center of the guard over the line feed head (Figure 1).

2. Slide the guard into slot provided and tighten hex head screws with hex wrench included

(Figure 2).

3. The guard is not

4. Once the guard is installed, remove the covering from the line cut-off blade, located on the
edge of the guard.

5. Adjust the length of the tube by pushing the button and moving the tube up or down as
shown in Figure 8.

6. Secure the extension cord with the cord retainer as shown in Figure 3.

OPERATING INSTRUCTIONS

CAUTION: ALWAYS WEAR EYE PROTECTION

CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects

which could become entangled in the rotating line or spool. Be particularly careful to avoid any
wire which might be bent outwardly into the path of the tool, such as barbs at the base of a
chain link fence.

• With the unit on, slowly swing the trimmer side to side as shown in Figure 5.

• To convert for maintenance edging, unplug the unit from the power source. Gently pull the

wire edge guide down into place as shown in Figure 7. Push the button and rotate the
tube 180° as shown in Figure 6. The tool will lock in the edger position. Unit is shipped in
the edging position.

• To operate as a maintenance edger, position the trimmer above the surface as shown in

Figure 7.

• Return to the trimming position by unplugging the unit from the power source, pushing the

button and rotating the tube back 180°. The tool will lock in the trimmer position. When
using the tool put up the wire edge guide to the original position, out of the way.

CUTTING LINE
LINE FEEDING

Your trimmer uses .080 in. (2mm) diameter, ROUND nylon line to cut grass and weeds
quickly and easily. During use, the tips of the nylon lines will become frayed and worn
and the special self feeding line hub will automatically feed and trim a fresh length of line.

intended to be removed once installed.

Problem Possible Cause PossibleSolution

TROUBLESHOOTING

• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.

For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.

ACCESSORIES

Use Black & Decker replacement spool Model No. DF-080.
Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.

• USE ONLY .080 in. (2mm) DIAMETER NYLON MONOFILAMENT LINE. Do not use
serrated or heavier gauge line, as they will overload the motor and cause overheating.
The unit only functions properly with 0.080 in. (2mm) diameter nylon monofilament line.
This line is available at your local dealer or authorized service center.

WARNING: The use of any accessory not recommended by Black & Decker for use with

this tool could be hazardous.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state or province to province. Should you
have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, check country specific warranty information contained in the
packaging, call the local company or see the website for warranty information.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

• Circuit fuse is blown. • Replace circuit fuse. (If the product
repeatedly causes the circuit fuse to

blow, discontinue use immediately and
have it serviced at a Black & Decker
service center or authorized servicer.)

• Circuit breaker is tripped. • Reset circuit breaker. (If the product
repeatedly causes the circuit breaker to
trip, discontinue use immediately and
have it serviced at a Black & Decker
service center or authorized servicer.)

• Cord or switch is • Have cord or switch replaced at Black

damaged. & Decker Service Center or Authorized

Servicer

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales