www.blackanddecker.com.au
www.blackanddecker.co.nz
FSMH13E10
10
11
12
1
3
9
4
2
5
8
6
7
2
8
9
14
13
5
6
A
B
6
7
C
4
3
11
10
D E
3
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKERTM FSMH13E10
designed for sanitising and cleaning sealed hardwood, sealed
laminate, linoleum, vinyl, ceramic tile, stone and marble floors.
This appliance is intended for indoor household use only.
steam mop has been
Safety Instructions
Warning! Read all Safety,
Maintenance, Service' manual
t
carefully before operating
this appliance. Read all of this
manual carefully before operating this appliance.
Safety of others
u This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved.
u Children shall not play with the appli-
ance. Cleaning and user maintenance
shall not be made by children without
supervision.
u If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
u The plug must be removed from the
socket-outlet before cleaning or maintaining the appliance.
u The liquid or steam must not be
directed towards equipment containing electrical components, such as the
interior of ovens.
u The appliance shall not be left unat-
tended while it is connected to the supply mains;
u The appliance is not to be used if it
has been dropped, if there are visible
signs of damage or if it is leaking;
u Keep the appliance out of reach of
children when it is energized or cooling
down.
Labels on appliance
The following pictograms along with the
date code are shown on the appliance.
CAUTION Hot Steam
Features
1. On/off switch
2. Steam operate button
3. Water tank access tab
4. Water tank
5. Steam head connector
6. Steam head
7. Steam head cleaning pad
8. Handle connector button
9. Handle
10. Cable tidy hook
11. Grip
12. Power cable
Assembly
Warning! Before attempting any of the following
@
Attaching the handle (Fig. A)
u Slide the bottom end of the handle (9) into the top end of
Attaching the steam head (Fig. B)
u Connect the steam mop body to the steam head (6) via
Attaching a cleaning pad (Fig. C)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
u Place a cleaning pad (7) on the floor with the velcro 'loop'
instructions, make sure that the appliance is
switched off and unplugged and the appliance is
cold and does not contain any water.
the steam mop body until the handle connector button (8)
clicks into place.
the steam head connector (5), ensuring the connection
button (13) clicks into place in the the opening (14) .
side facing up.
4
(Original instructions)
ENGLISH
u Lightly press the steam mop down onto the cleaning pad
(7).
Caution: Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (9) to the upright position and turn the
steam mop 'OFF'.
u Wait until the steam mop cools down (approximately 5
minutes).
u Lift the steam mop away from the cleaning pad freeing it
from the velcro fastening.
Caution! Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Filling the water tank (Fig. D)
Note! Do not use chemical cleaners with your steam mop
water tank.
Note! Fill the water tank with clean tap water.
Note! In areas of hard water, the use of de-ionised water is
recommended.
u Open the water tank access tab (3).
u Fill the water tank (4) with water.
Warning! Your water tank has a 380ml capacity. Do not over
fill the tank
u Replace the water tank access tab.
Note! Ensure the water tank access tab is firmly secured
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pad fitted and a continuous run tim
of 90 seconds.
Switching on and off
u To switch the appliance on, press the ON/Off button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
u Press the steam operation button (2). This will operate the
pump and the unit will begin to produce steam.
u To stop steam generation, turn the steam operation button
(2) to off. This will maintain power to the boiler for quicker
start up.
u To switch the appliance off, press the ON/Off button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (9) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running d , it can take up to 45
seconds for steam to be produced.
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
u Always vacuum or sweep the floor before using the steam
mop.
u The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at a
time.
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam Cleaning
u Place a cleaning pad (7) on the floor with the velcro 'loop'
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(7).
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note! When first filled or after running d , it can take up to 45
seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
u Push and pull the steam mop slowly across the surface to
thoroughly steam clean each section.
u When you have finished using the steam mop, return
the handle (9) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes)
Caution! It is important to monitor the water level in the water
tank (4). To refill the water tank and continue to sanitize
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, refill the water tank (4)
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (9) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
5
ENGLISH
(Original instructions)
After use (Fig. E)
u Turn the steam mop 'OFF'. turn the steam operation
button (2) to off and then press the ON/OFF button (1).
u Wait until the steam mop cools down.
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank.
u remove the cleaning pad (7) and wash it ready for next
use.
u Wrap the power supply cable around the tidy hook (10).
Technical Data
FSMH13E10
Voltage V
ac
230
Power W 1300
Tank
Capacity
ml 380
Weight kg 2.8
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Problem Step Possible solution
The steam mop is not
turning on
The steam mop is not
producing steam
Where can I get
further information/
accessories for my
steam mop
6
1. Check the unit is
2. Check the unit is
3. Check the fuse in the
4. Check the water tank
5. Check the steam
6. The steamer is
7. Refer to the assembly
plugged in at the wall
socket.
switched on using the
ON/OFF switch (1)
plug.
(4) is full .
NOTE: When first fille
or after running dry it
can take up to 45
seconds for steam to
be produced.
generation button is in
the ON position (2).
equipped with a
thermostat and a
thermal cut-out. If for
any reason the steamer
overheats it will switch
off. If this happens turn
off and unplug the
steamer, allow to cool
for 2 to 4 hours and
re-try.
chapter of the manual
for correct fitting of
parts and
accessories.
Australia & New Zealand
Stanley Black & DeckerSt
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
(Original instructions)
ENGLISH
7
N500349 08/2017
Loading...