Black & Decker Fsm1630nd Instruction Manual

Page 1
FSM1630ND
Page 2
A
B
C
E
2
D
Page 3
F
G
H
J
I
3
Page 4
(Original instructions)
Intended use
Your Black & Decker steam mop has been designed for sanitising and cleaning sealed hardwood, sealed laminate, linoleum, vinyl, ceramic tile, stone and marble oors and for refreshing carpets. This appliance is intended for indoor household use only.
Warning! Read all of the 'Safety, Maintenance, Service' manual carefully before operating this appliance.
Read all of this manual carefully before operating the appliance.
Features
This appliance includes some or all of the following features.
1. ON/Off switch
2. AutoselectTM button
3. Removable water tank
4. Handle
5. Steam head
6. Steam head cleaning pad
7. Resting mat
8. Carpet glider
9. Bottom cable tidy hook
10. Top cable tidy hook
11. Cable management clip
Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
u Slide the bottom end of the handle (4) into the top end
of the steam mop body (12) until it clicks into place. The arrow on the handle (4) should be aligned with the top of the steam mop body (12).
Attaching the steam head (Fig. B)
u Slide the bottom end of the steam mop body (2) onto the
steam head (5) until it clicks into place.
u The steam head can be removed from the Steam mop
body by pressing the steam head release button (13) and pulling the steam mop body (12) off the steam head (5).
Attaching the water jug (Fig. C)
u Clip the water jug (3) onto the handle (4). u Slide the water jug (3) down into the Steam mop body
(12), ensure that the water jug is rmly seated.
4
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black & Decker dealer:- (cat. no. FSMP20-XJ).
u Place a cleaning pad (6) on the oor with the ‘hook & loop’
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(6). Caution! Always place your steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or open toed footwear.
u Return the handle (4) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
u Place the front of your shoe onto the cleaning pad removal
tab (14) and press down rmly.
u Lift the steam mop up off the cleaning pad.
Caution! Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. F)
The water tank on your steam mop is removable for conven­ient and easy lling. This Steam Mop incorporates an anti-calc system to help prolong the life of the system.
Note: Fill the water tank with clean tap water. Note: In areas of very hard water, the use of de-ionised water
is recommended.
u Remove the water tank (3). u Open the ller cap (16) by pressing the release button
(17).
u Fill the water tank (3) with water.
Warning! Your water tank has a 0.5 litre capacity. Do not over ll the tank.
u Re-t the ller cap (16). u Re-t the water tank (3).
Note: Ensure the ller cap is rmly secured. Note: Do not use chemical cleaners with your steam mop..
Attaching the carpet glider (Fig. G) (For use on carpets only)
u Place carpet glider on the oor. u Attach a cleaning pad to the unit. u Lightly press the steam mop down onto the carpet glider
(8) until it clicks into place. Caution! Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and
Page 5
(Original instructions)
make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or open toed footwear.
u Return the handle (4) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
u Place the front of your shoe onto the carpet glider removal
tab (15) and press down rmly.
u Lift the steam mop up off the carpet glider (8).
Caution! Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro bre pad tted and a continuous run time of 90 seconds.
Switching on and off
u To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the steam mop to
heat up. Note: When the steam mop is rst turned on the water res­ervoir will glow red. Once the steam mop is ready to use the water reservoir will glow blue.
u To switch the appliance off, press the ON/OFF button (1).
Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Caution! Always empty the steam mop after use. Note: When rst lled or after running dry it can take up to 45
seconds for steam to be produced.
AutoselectTM Technology (Fig. H)
This steam mop is tted with an AutoselectTM button (2) which shows various cleaning applications. They are used to select the correct operating mode for your particular cleaning operation. Using AutoselectTM , choose from one of the following applica­tions by pressing the autoselect button (2) until the required setting is selected:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
The steam mop will select the correct volume of steam required for your particular cleaning operation. Note: Always check you are using the correct setting before using your steam mop. For convenience the steam mop will remember the last setting you chose.
Steam burst (Fig. H)
The steam mop is equipped with a steam burst button to aid in the removal of stubborn marks and stains.
u During use, press the steam burst button (18) to apply
extra cleaning power. Note: The steam burst will last for 10 seconds then the steam mop will return to the chosen setting.
Hints for optimum use
General Caution! Never use the steam mop without rst attaching a
cleaning pad.
u During use you can use the cable management clip (11) to
keep your cable out of the way of the work area..
u Always vacuum or sweep the oor before using the steam
mop.
u The easiest way to use the machine is to tilt the handle to
a 45˚ angle and clean slowly, covering a small area at a
time.
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum oors, you
can use the steam burst button to apply extra steam to
the area or pre-treat with a mild detergent and some water
before using the steam mop.
Steam cleaning
u Place a cleaning pad (6) on the oor with the ‘hook & loop’
side facing up.
u Raise the steam mop off the resting mat (7) and lightly
press it down onto the cleaning pad (6).
u Place the steam mop on the resting mat. u Connect the steam mop to the mains. u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u Press the Autoselect
reached.
TM
button (2) till the required setting is
5
Page 6
(Original instructions)
u Pulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head. Note: When rst lled or after running dry it can take up to 45 seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
u Push and pull the steam mop slowly across the oor to
thoroughly steam clean each section. Note: During use you may turn off the steam pump by return­ing the handle to the upright position, this convenient feature will allow you to place the steam mop on the resting mat for a short time so that you may move items of furniture, then continue cleaning without the need to switch the appliance off.
u When you have using the steam mop, return the handle
(4) to the upright position and turn it ‘OFF’, place it on the
resting mat (7) and wait until the steam mop cools down.
(approximately ve minutes) Caution! It is important to monitor the water level in the water tank. To rell the water tank and continue to sanitise/clean, return the handle (4) to the upright position and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet, remove and rell the water tank (3). Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Carpet refreshing
u Place a cleaning pad (6) on the oor with the ‘hook & loop’
side facing up.
u Raise the steam mop off the resting mat (7) and lightly
press it down onto the cleaning pad (6).
u Place the carpet glider (8) on the oor. u Lightly press the steam mop down onto the carpet glider
(8) until it clicks into place.
u Place the steam mop on the resting mat. (7) u Connect the steam mop to the mains. u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u Press the Autoselect
TM
button (2) to the Wood/Laminate
setting.
u Pulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head. Note: When rst lled or after running dry it can take up to 45 seconds for steam to be produced.
u Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section. Note: During use you may turn off the steam pump by return-
ing the handle (4) to the upright position, this convenient feature will allow you to place the steam mop on the resting mat (7) so that you may move items of furniture with out the need to switch the appliance off.
u When you have nished using the steam mop, return the
handle (4) to the upright position and turn it ‘OFF’, place it on the resting mat (7) and wait until the steam mop cools
down. (approximately ve minutes) Caution! It is important to monitor the water level in the water tank. To rell the water tank and continue to sanitise/clean, return the handle (4) to the upright position and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet, remove and rell the water tank (3). Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
After use (Fig. I & J)
u Return the handle (4) to the upright position and turn the
steam mop ‘OFF’,
u Place the steam mop on the resting mat (7) and wait until
the steam mop cools down. (approximately ve minutes)
u Unplug the steam mop from the electrical wall outlet. u Empty the water tank (3). u Remove the cleaning pad (6) and wash it ready for next
use. (Take care to follow the wash care instructions
printed on the cleaning pad).
u Wrap the supply cable around the cable tidy hooks (9 &
10). Note: The top cable tidy hook (10) rotates to easily release the cable ready for next use.
u Clip the supply cable onto itself using the cable tidy clip
(10) close to the plug.
u Place steam mop on the resting mat (7) for storage.
Note: With the handle (4) in the upright position, the cable neatly wrapped around the cable tidy hooks (9 & 10) and secured with the cable tidy clip (19) your steam mop will stand on its own for storage. Alternatively there is a hanging bracket (20) built into the hand grip (21) which will allow your steam
6
Page 7
(Original instructions)
mop to be hung from a suitable hook on the wall. Always ensure that your wall hook is capable of supporting the weight of the steam mop safely.
Technical data
FSM1630
(Type 1)
Voltage V
Power W
Tank capacity ml
Weight kg 3.4
ac
230
1600
500
Troubleshooting
If your appliance seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local Black & Decker repair agent.
Problem Step Possible solutions
The steam mop is
not turning on.
The digital controls
do not light up.
The steam mop is
not producing
steam.
The digital controls
go out during use.
The steam mop
stops producing
steam during use.
Check the unit is plugged in at the wall
1
socket.
Check the unit is switched on using the on/
2
off switch (1).
3 Check the fuse in the plug.
Check that the handle (4) of the steam mop
4
is pushed rmly into the steam mop body
(12). Check that the arrow on the handle is
ush with the top of the steam mop body
(12).
5 Check steps 1, then 2, then 3.
The steam mop will only produce steam
6
once the handle is pulled back from the
upright position.
Check that the water tank (3) is full and
7
correctly tted.
NOTE: When rst lled or after running dry it
can take up to 45 seconds for steam to be
produced.
Check that the Steam head (5) is rmly
8
docked into the steam mop body (12).
9 Check steps 1, then 2, then 3.
10 Check steps 4, then 5, then 1, then 2, then 3
11 Check steps 6, then 7, then 8, then 4, then 3.
Problem Step Possible solutions
The steam mop is
producing too
much steam during
use.
The steam mop is
producing too little
steam during use.
Steam is escaping
from unexpected
areas of the unit.
Where can I get
further information
/ accessories for
my steam mop.
The steam mop has 3 settings. Press the
12
autoselect button (2) to reduce the amount of
steam being produced.
Check that the steam burst button (18) has
13
not been pressed.
The steam mop has 3 settings. Press the
14
autoselect button (2) to increase the amount
of steam being produced.
Press the steam burst button (18) to
15
temporarily increase the amount of steam.
Refer to the assembly chapter of the manual
16
for correct tting instructions of all parts and
accessories.
17 www.blackanddecker.co.uk/steammop
www.blackanddecker.ie/steammop
7
Page 8
FSM1630ND
4
TYPE
1
1
20
2
6
21
3
8
25
9
E16773
10
11
www.2helpU.com
12
16
15
14
17
17 - 10 - 12
Page 9
9
Page 10
10
Page 11
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Page 12
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100 20 Fletcher Road, Mooroolbark, Fax 03-9727 5940 Victoria, 3138
New Zealand
Black & Decker Tel. +64 9 259 1133 5 Te Apunga Place Fax +64 9 259 1122 Mt Wellington Auckland 1060
United Kingdom
Black & Decker Tel. 01753 511234 210 Bath Road Fax 01753 551155 Slough, Berkshire SL1 3YD
90598591 REV-0 05/2013
Loading...