Page 1
Australia
New Zealand
Page 2
8
6
7
Fig C
Fig D
Fig B
11
10
9
12
Page 3
General Safety Rules
Warning! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury. The term “power tool” in all of the warnings
listed below refers to your mains operated (corded) power tool
or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1) Work area
a) Keep work area clean and well lit. Cluttered and dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
d) When operating a power tool outdoors, use an extension
cord suitable for outdoor use.Use of a cord suitable for
outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety
equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off
position before plugging in. Carrying power tools with your
finger on the switch or plugging in power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Press properly. Do not wear loose clothingor jewellery.
Keep your hair, clothing and gloves away from moving parts.
Loose clothes,jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can reduce
dust related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before making
any adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for is alignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tools operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely
to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking into
account the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts.This will ensure that the
safety of the power tool is maintained.
Additional Safety Instructions Drills
a) Wear ear protectors with impact drills. Exposure to noise
can cause hearing lose.
b) Use auxiliary handles supplied with tool. Loss of control
can cause personal injury.
Page 4
Additional Safety Instructions For Australia And New
Zealand
a) Young children and the infirm. This appliance is not intended
for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not
play with this appliance.
b) Replacement of the supply cord. If the supply cord is
damaged, it must be replaced by the manufacturer or an
authorised DEWALT Service Centre in order to avoid a hazard.
Electrical safety
This tool is double insulated; therefore no earth wire is required.
Always check that the power supply corresponds to the voltage
on the rating plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Keyless chuck
6. Depth stop
7. Side handle
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting the side handle and depth stop (fig. B)
•
Turn the grip (7) counterclockwise until you can slide the side
handle (8) onto the front of the tool as shown.
•
Rotate the side handle into the desired position.
•
Insert the depth stop (6) into the mounting hole
as shown.
•
Set the depth stop to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the depth stop.
•
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyless chuck (fig. C)
•
Open the chuck by turning the front part (10) with one hand
while holding the rear part (9) with the other.
•
Insert the bit (11) shaft into the chuck and firmly tighten the
chuck.
Removing and refitting the chuck
Keyless chuck (fig. D)
•
Open the chuck as far as possible.
•
Remove the chuck retaining screw, located in the front part of
the chuck, by turning it clockwise using a screwdriver.
•
Tighten an Allen key (12) into the chuck and strike it with a
hammer as shown.
•
Remove the Allen key.
•
Remove the chuck by turning it counterclockwise.
•
To refit the chuck, screw it onto the spindle and secure it with
the chuck retaining screw.
Warning! Always make sure that the chuck is securely fitted.
Use
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the direction of rotation
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
•
To select forward rotation, push the forward/reverse slider
(3) to the left.
•
To select reverse rotation, push the forward/reverse slider to
the right.
Warning! Never change the direction of rotation while the motor
is running.
Selecting the drilling mode
•
For drilling in masonry, set the drilling mode selector (4) to
the position.
•
For drilling in other materials and for screwdriving, set the
drilling mode selector (4) to the position.
Switching on and off
•
To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch. As a
general rule, use low speeds for large diameter drill bits and high
speeds for smaller diameter drill bits.
•
For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available only
at full speed.
•
To switch the tool off, release the variable speed switch. To
switch the tool off when in continuous operation, press the
variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to high
quality standards and designed to enhance the performance of
your tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots with a clean, dry paint
brush. To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse any
part of the tool into liquid.
Protecting the environment
Black & Decker provides a facility for recycling Black & Decker
products once they have reached the end of their working life.
This service is provided free of charge. To take advantage of
this service please return your product to any authorised repair
agent who will collect them on our behalf. You can check the
location of your nearest authorised repair agent by contacting
your local Black & Decker office at the address indicated in this
manual. Alternatively, a list of authorised Black & Decker repair
agents and full details of our after-sales service and contacts are
available on the Internet at: www.2helpU.com.
Page 5
Technical data
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014, EN
61000
LpA (sound pressure): 97.3 dB(A),
LWA (acoustic power):110.3 dB(A),
hand/arm weighted vibration 10.7 m/s2
Bill Lessig
Director of Consumer Engineering
Towson, Maryland 21286,
United States
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is in
addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member States
of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair wear and tear
or replace such products to ensure minimum inconvenience to
the customer unless:
• The product has been used for trade, professional or hire
purposes;
• The product has been subjected to misuse or neglect;
• The product has sustained damage through foreign objects,
substances or accidents;
• Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised Black
& Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Please register at our website www.blackanddecker.com
to be kept up to date on new products and special offers.
Further information on the Black & Decker brand and our range
of products is available at www.blackanddecker.com.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road Tel. 03 8720 5100
Mooroolbark, Victoria 3138 Fax 03 9899 7465
New Zealand
Black & Decker Tel. 09 579 7600
81 Hugo Johnston Drive Fax 09 579 8200
Penrose, Auckland, New Zealand
Page 6
TYP
1
WWW.2helpU.com
FS6000-XE
26
12
15
20
17
16
25
23
24
40
42
8
13
7
10
9
6
29
19
14
18
4
5
34
43
41
800
2
1
11
27
1
28
21
22
Loading...