Black & Decker 622675-00, FS6000HD User Manual

serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make

exposed metal parts of the tool "live" and shock the operator.

• When working on a ladder or on scaffolding be sure to lay the tool down on its side when not in use. Some tools with large battery packs will stand upright but may be easily knocked over.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury.Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

WARNING: Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating current

......................direct current

o........................no load speed

..........................

Class II Construction

........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations per minute

SAFETY WARNINGS

AND INSTRUCTIONS: DRILLS

• When drilling or driving into walls, floors or wherever live electrical wires may be

encountered, DO NOT TOUCH ANYMETALP ARTS OF THE TOOL! Hold the tool only by the plastic handle to prevent shock.

• Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.

• Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a

side handle, always use the side handle.

WARNING:Drill may stall (if overloaded or improperly used) causing a twist. Always expect

the stall. Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

• Always unplug the drill when attaching or removing accessories. When attaching accessories

in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

MOTOR

Your Black & Decker tool is powered by a Black & Decker-built motor. Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your drill will operate on standard 60 Hz household power. Do not operate AC tools on DC. Arating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in overheating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.

USE OF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the tool – that is, proper wire size for various lengths of cord and heavy

General Safety Rules

WARNING: Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. Amoment of inattention while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on.Awrench or key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off.Any tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tools operation. If damaged, have the tool

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR ELPRODUCTO.

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544-6986)

IF YOU SHOULD EXPERIENCE APROBLEM

WITH YOUR BLACK &DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986)

BEFORE YOU CALL, HA VE THE FOLLOWING INFORMATION A VAILABLE, CATALOG No., TYPE No., AND DATE CODE. IN MOSTCASES, ABLACK & DECKER REPRESENTA TIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT,

GIVE US ACALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

FEATURES

1. Variable speed switch

2. Lock-on button

3. Forward/reverse slider

4. Drilling mode selector

5. Keyless chuck

6. Depth stop

7. Side handle

A B

CATALOG NUMBER

FS6000HD

INSTRUCTION

MANUAL

1111////2222"""" ((((11113333mmmmmmmm)))) HHHHaaaammmmmmmmeeeerrrr DDDDrrrriiiillllll

enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in line voltage resulting in loss of power and overheating. For proper size cords see chart below.

ASSEMBLY

WARNING:

Always unplug drill from power supply before any of the following operations.

FITTING THE SIDE HANDLE AND DEPTH STOP (FIG.A)

•Turn the side handle grip (7) counterclockwise until you can slide the side handle onto the front of the tool as shown.

• Rotate the side handle into the desired position.

• Insert the depth stop (6) into the mounting hole as shown.

• Set the depth stop to the desired position. The maximum drilling depth is equal to the distance between the tip of the drill bit and the front end of the depth stop.

•Tighten the side handle by turning the grip clockwise.

FITTING A DRILL BIT OR SCREWDRIVER BIT (FIG. B)

• Open the chuck by turning the front part (8) with one hand while holding the rear part (9) with the other.

• Insert the bit shaft (10) into the chuck and firmly tighten the chuck.

REMOVING AND REFITTING THE CHUCK (FIG. C)

• Open the chuck as far as possible.

• Remove the chuck retaining screw, located in the front part of the chuck, by turning it clockwise using a screwdriver.

•Tighten an Allen key (11) into the chuck and strike it with a hammer as shown.

• Remove the Allen key.

• Remove the chuck by turning it counterclockwise.

•To refit the chuck, screw it onto the spindle and secure it with the chuck retaining screw.

OPERATION

WARNING: To reduce the risk of serious personal injury, read, understand and follow all

important safety warnings and instructions prior to using tool.

SELECTING THE DIRECTION OF ROTATION

• For drilling and for tightening screws, use forward (clockwise) rotation. For loosening screws or removing a jammed drill bit, use reverse (counterclockwise) rotation.

•To select forward rotation, push the forward/reverse slider (3) to the RIGHT (when viewed from the chuck end).

•To select reverse rotation, push the forward/reverse slider (3) to the LEFT (when viewed from the chuck end).

WARNING: Never change the direction of rotation while the motor is running.

SELECTING THE DRILLING MODE

• For drilling in masonry, set the drilling mode selector (4) to the position.

• For drilling in other materials and for screwdriving, set the drilling mode selector (4) to the position.

SWITCHING ON AND OFF

•To switch the tool on, press the variable speed switch (1). The tool speed depends on how far you press the switch. As a general rule, use low speeds for large diameter drill bits and high speeds for smaller diameter drill bits.

• For continuous operation, press the lock-on button (2) and release the variable speed switch. This option is available only at full speed.

•To switch the tool off, release the variable speed switch. To switch the tool off when in continuous operation, press the variable speed switch once more and release it.

WARNING:The drill should only be locked ON when it is held stationary in a drill press stand or other means; NOT BY HAND! Never unplug the tool with the locking feature engaged. To do so will cause the tool to start immediately the next time it is plugged in.

DRILLING

• Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the safety instructions.

• Secure and maintain work area, as instructed in the safety instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly to control its twisting action..

• DO NOT CLICK THE TRIGGER OF AST ALLED DRILLOFF AND ON IN AN A TTEMPTTO STAR TIT . DAMAGE TO THE DRILLCAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

• Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The lubricants that work best are sulphurized cutting oil or lard oil. Bacon grease will also serve.

• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear chips from the flutes.

• Plug in drill. Make sure switch turns drill on and off.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY , repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO (544-6986).

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow pages directory under "Tools—Electric" or call: 1-800-54-HOW-TO.

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "ToolsElectric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage Than Than 0-6 18 16 16 14 6-10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

MAXIMUM RECOMMENDED CAPACITIES

Steel / Concrete 1/2” (13mm) Wood 1” (25mm)

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

RÈGLES DE SÉCURITÉ – GÉNÉRALITÉS

AVERTISSEMENT : Lire, comprendre et suivre toutes les directives précisées ci-dessous, y compris les consignes de sécurité, afin d’éviter les risques de choc électrique, d’incendie ou de blessure grave.

Conserver le présent guide à titre de référence

AIRE DE TRAVAIL

•L’aire de travail doit être propre et bien éclairée. Les établis encombrés et les endroits sombres peuvent entraîner des accidents.

• Ne pas faire fonctionner des outils électriques dans des atmosphères explosives, comme en présence de liquides, de gaz et de poussières inflammables. Les outils

électriques produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.

•Tenir les enfants, les visiteurs ou toute autre personne à l’écart lorsqu’on utilise un outil électrique; les distractions peuvent faire perdre la maîtrise de ce dernier

MESURES DE SÉCURITÉ – ÉLECTRICITÉ

• Les outils à double isolation sont munis d’une fiche polarisée (c’est-à-dire que l’une des lames est plus large que l’autre), laquelle ne peut être raccordée qu’à une prise polarisée et ce, dans un seul sens; on doit l’inverser si on est incapable de l’enfoncer complètement. Si la fiche ne s’adapte toujours pas, on doit faire appel à un électricien qualifié pour qu’il installe la prise appropriée. On ne doit jamais modifier la fiche. La double isolation élimine le besoin d’installer un cordon

d’alimentation trifilaire et un système d’alimentation électrique pourvus d’une mise à la terre.

• Éviter tout contact entre le corps et les éléments mis à la terre, comme les tuyaux, les radiateurs, les cuisinières et les réfrigérateurs, afin de réduire les risques de choc

électrique.

• Ne pas utiliser l’outil électrique dans des endroits mouillés, ni l’exposer à la pluie;

l’infiltration d’eau à l’intérieur de l’outil augmente les risques de choc électrique.

• Ne pas utiliser le cordon de manière abusive; on ne doit pas transporter l’outil en le tenant par le cordon, ou utiliser ce dernier pour le débrancher. On doit tenir le cordon à l’écart des sources de chaleur, de l’huile, des bords tranchants ou des pièces mobiles. Remplacer immédiatement les cordons endommagés, car ces

derniers augmentent les risques de choc électrique.

• Lorsqu’on utilise un outil électrique à l’extérieur, on ne doit utiliser que des rallonges conçues pour cet usage, comme celles de type W-Aou W, afin de réduire

les risques de choc électrique.

SÉCURITÉ PERSONNELLE

• Rester vigilant en tout temps et faire preuve de jugement lorsqu’on utilise un outil électrique; ne pas utiliser l’outil lorsqu’on est fatigué ou sous l’influence de drogues, d’alcool ou de médicaments, car un moment d’inattention pourrait entraîner

des blessures graves.

• Porter des vêtements appropriés. Ne pas porter des vêtements amples ou des bijoux. Couvrir ou attacher les cheveux longs. Garder les cheveux, les vêtements, les

bijoux et les gants éloignés des pièces mobiles, car ceux-ci peuvent s’y coincer. Se tenir éloigné des évents puisque ces derniers pourraient camoufler des pièces mobiles.

• Éviter les démarrages accidentels; s’assurer que l’interrupteur est en position d’arrêt avant de brancher l’outil. Ne pas transporter l’outil en laissant le doigt sur

l’interrupteur ni le brancher lorsque l’interrupteur est en position de marche, car cela pourrait causer un accident.

• Retirer les clés de réglage avant de démarrer l’outil. Une clé laissée sur une pièce rotative pourrait entraîner des blessures.

• Ne pas trop étendre les bras; les pieds doivent rester ancrés fermement au sol afin de maintenir son équilibre en tout temps et de mieux maîtriser l’outil dans des

situations imprévues.

• Utiliser le matériel de sécurité approprié; toujours porter des lunettes de protection.

Porter un masque anti-poussières, des chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la situation le requiert.

UTILISATION ET ENTRETIEN DE L’OUTIL

• Fixer et soutenir la pièce sur une plate-forme stable au moyen d’une bride de serrage ou de tout autre dispositif semblable. La pièce est instable lorsqu’on la retient

manuellement ou qu’on l’appuie contre le corps, ce qui pourrait faire perdre la maîtrise de l’outil.

• Ne pas forcer l’outil ni l’utiliser pour des travaux autres que ceux pour lesquels il a été conçu. Pour obtenir de meilleurs résultats et prévenir les risques de blessure, laisser

l’outil couper à la vitesse pour laquelle il a été conçu.

• Ne pas utiliser l’outil lorsque l’interrupteur marche-arrêt ne fonctionne pas. Tout outil qui ne peut être commandé au moyen de l’interrupteur est dangereux et doit être réparé.

• Débrancher l’outil de la source d’alimentation électrique avant d’effectuer un réglage, de changer les accessoires ou de ranger l’outil; ces mesures de sécurité

préventives réduisent les risques de démarrage accidentel.

• Lorsqu’on n’utilise pas l’outil, le ranger hors de la portée des enfants ou des personnes non qualifiées. Les outils sont dangereux entre les mains de personnes

inexpérimentées.

• Bien entretenir l’outil; s’assurer qu’il est toujours bien propre et aiguisé. Les outils bien entretenus et dont les bords sont bien tranchants sont moins susceptibles de rester coincés et sont plus faciles à maîtriser.

• Vérifier les pièces mobiles afin de s’assurer qu’elles sont bien alignées et qu’elles ne restent pas coincées. Vérifier également les pièces afin de s’assurer qu’il n’y a aucun bris ni aucune autre condition susceptible de nuire au bon fonctionnement de l’outil. Faire réparer l’outil si ce dernier est endommagé avant de s’en servir à nouveau, car les accidents sont souvent causés par des outils mal entretenus.

• N’utiliser que les accessoires recommandés par le fabricant pour le modèle concerné. Un accessoire destiné à un outil particulier peut devenir dangereux lorsqu’il est

utilisé avec un autre.

ENTRETIEN

•L’outil doit être entretenu par le personnel qualifié seulement; toute maintenance effectuée par une personne non qualifiée pourrait entraîner des risques de blessure.

• Lors de l’entretien, n’utiliser que des pièces de rechange identiques et suivre les directives précisées à la section « Entretien » du présent guide afin de prévenir les

risques de choc électrique ou de blessure.

NO DE CAT. FS6000HD

GUIDE D’UTILISATION

AAAARRRRTTTTEEEEAAAAUUUUPPPPEEEERRRRFFFFOOOORRRRAAAATTTTEEEEUUUURRRRDDDDEE

11113333

MMMMMM

((((1111////2222

PPPPOO

))

AAAAVVVVAAAANNNNTTTT DDDDEEEE RRRREEEETTTTOOOOUUUURRRRNNNNEEEERRRR LLLLEEEE PPPPRRRROOOODDDDUUUUIIIITT

PPPPOOOOUUUURRRR QQQQUUUUEEEELLLLQQQQUUUUEEEE RRRRAAAAIIIISSSSOOOONNNN QQQQUUUUEEEE CCCCEEEE SSSSOOOOIIIITTTT,,,,

CCCCOOOOMMMMPPPPOOOOSSSSEEEERRRR LLLLEE

1111 888800000000 555544444444----66669999888866

+ 3 hidden pages