Black & Decker FS1600R User Manual

www.blackanddecker.ae

FS1600R

ENGLISH

Parts Identification

1. Front guard

2. Locking screw

3. Guard securing clip

4. Guard ring

5. Blade cap

6. Fan blade

7. Guard lock nut

8. Rear guard

9. Motor shaft

10. Main unit

11. Oscillation control knob

12. Control panel

13. Securing screw

14. Switch housing

15. Adjusting tube

16. Tighten/ loosen screw

17. Support tube

18. Base plate 19 Screw

20. Base plate screw

21. Handle

22. Remote control

23. Two AAA size Alkaline batteries

ENGLISH

Intended use

Your Black & Decker fan has been designed for indoor household use only. Remove all the parts from the packaging material and keep them aside . Ensure that you have all the parts as identified in the part identification list else get in touch with your nearest Black & Decker service agent assistance.

Read this entire manual carefully before using the appliance.

Safety instructions

• Warning! When using mains-powered

appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.

• The intended use is described in this manual.

The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.

• Retain this manual for future reference.

Using your appliance

• Always take care when using the appliance.

• Do not use the appliance outdoors.

• Do not operate the appliance if your hands

are wet. Do not operate the appliance if you are barefoot.

• Never pull the power supply cord to

disconnect the plug from the socket. Keep the power supply cord away from heat, oil and sharp edges.

• If the power supply cord is damaged during

use, disconnect the appliance from the power supply immediately. Do not touch the power supply cord before disconnecting from the power supply.

• Disconnect the appliance from the power

supply when not in use and before cleaning.

Safety of others

• This appliance is not intended for use by

persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that

they do not play with the appliance.

After use

• Switch off, remove the plug from the socket

and let the appliance cool down before leaving it unattended and before changing, cleaning or inspecting any parts of the appliance.

• Guide the power supply cord neatly so it

does not hang over the edge of a worktop and cannot be caught accidentally or tripped over.

• When not in use, the appliance should be

stored in a dry place. Children should not have access to stored appliances.

ENGLISH

Inspection and repairs

• Switch off the appliance before cleaning,

changing accessories or approaching parts which move in use

• Before use, check the appliance for

damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation.

• Do not use the appliance if any part is

damaged or defective.

• Have any damaged or defective parts

repaired or replaced by an authorised repair agent.

• Before use, check the power supply cord for

signs of damage, ageing and wear.

• Do not use the appliance if the power supply

cord or mains plug is damaged or defective.

• If the power supply cord or mains plug is

damaged or defective it must be repaired by an authorised repair agent in order to avoid a hazard. Do not cut the power supply cord and do not attempt to repair it yourself.

• Never attempt to remove or replace any

parts other than those specified in this manual.

Electrical safety

Before use, check that the mains voltage corresponds to the voltage on the rating plate.

This appliance is double insulated in accordance with EN 60335-2-14; therefore no earth wire is required.

• To avoid the risk of electric shock, do not

immerse the cord, plug or motor unit in water or other liquid.

• Check that the supply voltage shown on the

rating plate of the appliance matches that of your electrical system. Any connection error will invalidate the guarantee.

Mains Plug Replacement

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal of

the new plug.

• Connect the blue lead to the neutral terminal.

• If the product is class l (earthed), connect the

green / yellow lead to the earth terminal.

Warning! If your product is class ll double insulated (only 2 wires in the cord set), no connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs

Any replacement fuse must be of the same rating as the original fuse supplied with the product.

• If the supply cord is damaged, it must be

replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.

• Allow the appliance to cool before fitting or

removing any parts and before cleaning.

• Do not immerse the appliance in liquid.

Fitting and Assembling

Make sure your fan is switched off before connecting to or disconnecting from power supply. Ensure that the voltage rating on the base plate corresponds to the main voltage at your home.

ENGLISH

Assembling of base and stand

1. Rotate the screw in the anti-clockwise direction and remove it from the support tube.

2. Place the support tube onto the base and then tighten the screw in the clockwise direction.

3. To assemble the main unit, release a few inches of the adjustable tube by operating the screw.

Motor Rear guard Fan blade Front guard

2. Mount the fan blade onto the motor shaft. Fasten the blade cap by rotating it in the anti-clockwise direction until the blade is fixed firmly into place.

3. Open the securing clip at the bottom of the front guard and loosen the clip screw. Position the top clip on the uppermost part of the rear guard. Push the top clip down and press rim of the front guard onto the rear guard. Close the bottom clip and tighten the screw.

Operations

Your Fan has three speed control to keep the desired air flow through your room

4. Fit the main unit on the adjustable tube and secure it in place by tightening the screw.

Assembly of the fan

1. To install the rear guard, remove the blade cap and guard nut from the motor shaft. Then attach the rear guard by positioning it on the location pins on the main unit. Secure the guard on to the motor body by fastening the guard nut, turning it clockwise until the guard is locked into position.

Finish

0 - Off 1 - Low 2 - Medium

3 - High You can press the oscillating control knob down

to make the fan oscillate to position the fan in specific direction pull the knob up.

ENGLISH

The Fan guard can also be positioned vertically depending upon the direction of flow desired. For this switch OFF the fan first, let the fan come to halt, then with one hand hold the stand and with the other hand, move the guard assembly up or down depending upon the desired angle required. To make the fan oscillate pin down. To make it stop oscillation, pull it up.

ON/OFF button

Your fan can be controlled by pushing the buttons, which can be set on the Control panel or on the Remote Control.

Press the On/Off button once to operate the fan and once again to make the fan stop running.

ON/OFF

Speed button

Your Fan has a speed control button to keep the desired air flow through your room. The speed of the fan can be adjusted by pressing the button. The speed will be displayed on the LCD. To increase the speed press the ” + “ button continually until it reaches the maximum of 4.To decrease the speed press the “ _ ” button continually until the running speed reaches the minimum of 1. The can be operated by remote control as well fan.

SPEED

Timer

The timer can be used to set the running time of the fan, which can vary from 1 to 8 hrs. The number of times the timer button is pressed will

set the running time which will be displayed on the LCD.

For example: If the timer is pressed once, the operating time will be set at 1hr and if the timer is pressed 4 times, the operating time will be set at 4 hours. The can be operated by remote control as well fan.

The Fan guard can also be positioned vertically depending upon the direction of flow desired. For this switch OFF the fan first, let the fan come to a halt, then with one hand hold the stand and with the other hand, move the guard assembly up or down depending upon the desired angle required.

To make the fan oscillate, press the oscillation pin down. To make it stop oscillation, pull it up.

TIMER

Remote control

Please inset 2’AAA’ size batteries into the remote as per making in the remote cavity.

Always face the LED on your remote towards the fan when you are operating the fan with remote.

To increase the speed, press the increase speed button once with every press of button the speed increases by onestep.Your fan is a four speed fan.To run the fan at maxmimum speed , press the “speed+” button four times. In similar fashion, to reduce speed press the “speed_” button.

Your remote also has timer control functions. As explained under “Times” functioning, the “time+” & ”time_” buttons can be operated to set the running time of fan.

The On/Off button operates and switches off the fan from your remote.

ENGLISH

Replacing battery

With normal use, the batteries should last for about six months, when the remote no longer operates the fan, replace the batteries with new ones.

Always check your batteries inside the remote periodically to check for corrosion or leakage.

Warning !

•

Never use the fan without the guard in place

or if the guard is damaged.

• Do not touch moving parts

• Always allow motor to stop before

approaching the blades or changing an accessory.

• Operate the appliance only with dry hands.

• If the power supply cord is damaged during

use, disconnect the appliance from the power supply immediately . Do not touch the power supply cord before disconnecting from the power supply.

• When not in use, the

appliance should be stored in a dry place. Children should not have access to stored appliance.

• Do not cover the rear

housing of the fan with any cloth or curtain.

• Keep your fingers, long hair, loose clothes

and supply cord away from moving parts.

• Never pull the power cord to disconnect the

plug from the socket.

• Keep the power supply cord away from

heat, oil and sharp edges.

• Do not place the appliance on or near heat

source or in a heated oven

• Do not use the appliance outdoors. Always

protect the motor unit from water or excessive humidity

• Do not operate this unit in tropical climate or

in areas where the temperature exceeds 40ºC.

Technical Data

Voltage 220 – 240V ~ 50Hz Power input 60W Weight 8.75kg

ENGLISH

Protecting the environment

Separate collection. This product must not

be disposed of with normal household waste.

Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with other household waste. Make this product available for separate collection.

• Black & Decker provides a facility for

recycling Black & Decker products once they have reached the end of their working life. This service is provided free of charge. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

• You can check the location of your nearest

authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorized Black & Decker repair agents and full details of our after-sales service and contact are available on the Internet at: www.2helpU.com.

Guarantee

Black & Decker is confident of the quality of its products and offers an outstanding guarantee.

This guarantee statement is in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless:

The product has been used for trade,

professional or hire purposes;

The product has been subjected to misuse

or neglect;

The product has sustained damage

through foreign objects, substances or accidents;

Repairs have been attempted by persons

other than authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual.

Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.

+ 17 hidden pages