Page 1
Page 2
2
Battery Cap
2
1
•Variable Speed
Switch
•Forward/Reverse
Button
Page 3
3
––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––
EPP18ID-XE
18V CORDLESS IMPACT DRIVER
TECHNICAL DATA
Cordless Drill/ Driver
Voltage
No Load Speed
Max. Torque
Capacity
– Chuck Capacity
Weight
Battery
Voltage
Capacity
Weight
Charger
Approx. Charging Time
EPP18ID
18
0-2900
130
6.35mm Hex Chuck
1.12
18
1.5
0.87
3
V
/min
N.m
mm
kg
V
Ah
kg
Hour
INTENDED USE
Your Black & Decker 18V cordless impact driver has been
designed for all impact driving applications.
GENERAL SAFETY RULES
Warning! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains operated
(corded) power tool or battery operated (cordless) power
tool.
SAVE THESE INSTRUCTIONS.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric
shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
tool in unexpected situations.
Page 4
4
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Battery tool use and care
a. Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
b. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
c. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
d. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
e. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
ADDITIONAL SAFETY INSTRUCTIONS FOR
AUSTRALIA AND NEW ZEALAND
a. Young children and the infirm.This appliance is not
intended for use by young children or infirm persons
without supervision. Young children should be
supervised to ensure they do not play with this
appliance.
b. Replacement of the supply cord. If the supply cord is
damaged, it must be replaced by the manufacturer or
an authorised Black & Decker Service Centre in order to
avoid a hazard.
ADDITIONAL POWER TOOL SAFETY WARNINGS
Warning! Additional safety warnings for drills and
impact drills.
• Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
• Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord.
• Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and shock
the operator.
ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES AND CHARGERS
Batteries
• Never attempt to open for any reason.
• Do not expose the battery to water.
• Do not expose the battery to heat.
• Do not store in locations where the temperature may
exceed 40°C.
• Charge only at ambient temperatures between 4°C and
40°C.
• Charge only using the charger provided with the tool.
• When disposing of batteries, follow the instructions
given in the section “Protecting the environment”.
• Do not damage/deform the battery pack either by
puncture or impact, as this may create a risk of injury
or fire.
• Do not charge damaged batteries.
Chargers
Your charger has been designed for a specific voltage.
Always check that the mains voltage corresponds to the
voltage on the rating plate.
• Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and
damage.
• Never attempt to charge non-rechargeable batteries.
• If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised Black & Decker
Service Centre in order to avoid a hazard.
Page 5
5
• Do not expose the charger to water.
• Do not open the charger.
• Do not probe the charger.
LABELS ON THE CHARGER
The following symbols are found on your charger:
Your charging base is double insulated; therefore no
earth wire is required. Always check that the power supply
corresponds to the voltage on the rating plate.
The charging base is intended for indoor use only.
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when
performing an operation where the tool may
contact hidden wiring or its own cord. Contact with
a “live” wire will also make exposed metal parts of the
tool “live” and shock the operator.
• When working on a ladder or on scaffolding be sure
to lay the tool down on its side when not in use.
Some tools with large battery packs will stand upright
but may be easily knocked over.
• Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
• When fitting and changing accessories, always use the
instructions supplied with the accessory.
• Should your tool develop a fault, do not try to fix it
yourself, but take it to one of our authorized repair
agents.
SYMBOLS
The label on your tool may include the following symbols:
V volts
A Amperes
Hz Hertz
W Watts
min Minutes
Alternating current
Direct current
no No load speed
Class II Construction
Earthing terminal
Safety alert symbol
…/min Revolutions or reciprocations per minute
…/bpm Beats per minute
Using the 3 hr charger
• To charge the battery, remove it from the tool and slide
the charger receptacle onto the battery.
• Plug in the charger.
The battery will become warm while charging. After approx.
3 hours of charging, the battery will be sufficiently charged
for use in regular applications. After approx. 6 hours of
charging, the battery will be fully charged.
• Remove the charger receptacle from the battery.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOTcharge
the battery pack in an air temperature below +40°F
(+4.5°C), or above +105°F (+40.5°C).This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to
touch while charging. This is anormal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
• Check current at receptacle by plugging in a lamp or
other appliance.
• Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
• Move charger and battery pack to a location where the
surrounding air temperature is approximately 65°F 75°F (18°- 24°C).
• If charging problems persist, take the tool, battery pack
and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
also charge a partially used pack whenever you desire
with no adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminum foil, or any build up
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power
supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other
liquid.
Shock hazard! Do not allow any liquid to get inside
charger.Never attempt to open the battery pack for any
reason. If the plastic housing of the battery pack breaks or
cracks, return to a service center for recycling.
Safety warnings and Instructions: Drills
1. Hold drill firmly with one hand on the grip and the other
hand on the side handle as shown in figure E
2. When attaching accessories in the drill chuck, hand
tighten the keyless chuck firmly.
se
conditions. Follow the charging procedure. You may
done previously. DO NOT CONTINUE to use under the
Page 6
6
Warning! Drill may stall (if overloaded or improperly
used) causing a twist. Always expect the stall. Grip the drill
firmly to control the twisting action and prevent loss of
control which could cause personal injury. If a stall does
occur, release the trigger immediately and determine the
reason for the stall before re-starting.
OPERATING INSTRUCTIONS
Variable Speed Trigger Switch (Fig. 1)
To turn the tool on, squeeze the trigger switch. To turn the
tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop as soon as the trigger
switch is fully released. The variable speed switch enables
you to select the best speed for a particular application. The
more you squeeze the trigger, the faster the tool will
operate. Use lower speeds for starting holes without a
center punch, drilling in metals or plastics, or driving
screws. For maximum tool life, use variable speed only for
starting holes or fasteners.
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should be
avoided.
Forward/Reverse Control Button (FIG. 1)
A forward/reverse control button determines the direction of
the tool and also serves as a lock off button. To select
forward rotation, release the trigger switch and depress the
forward/reverse control button on the right side of the tool.
To select reverse, depress the forward/reverse control
button on the left side of the tool. The center position of the
control button locks the tool in the off position. When
changing the position of the control button, be sure the
trigger is released.
Quick Release Chuck – (FIG. 2)
NOTE: The chuck accepts 1/4 in. (6.35 mm) hex accesso-
ries only.
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
To install an accessory, pull the chuck collar away from
the front of the tool, insert the accessory, and release the
collar. The accessory is locked in place.
To remove an accessory, pull the chuck collar away from
the front of the tool, remove the accessory and release the
collar.
MAINTENANCE
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
• Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
• Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
NOTE
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at www.2helpU.com.
GUARANTEE
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement
is in addition to and in no way prejudices your statutory
rights. The guarantee is valid within the territories of the
Member States of the European Union and the European
Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 48
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
ensure minimum inconvenience to the customer unless:
Page 7
7
• The product has been used for trade, professional or
hire purposes;
• The product has been subjected to misuse or neglect;
• The product has sustained damage through foreign
objects, substances or accidents;
• Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service
staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You
can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com
Please visit our website www.blackanddecker.com.au to
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
products is available at www.blackanddecker.com.au
Page 8
90564042
06/10
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark, Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker Tel. +0800 339 258
5 Te Apunga Place Fax +64 9 259 1122
Mt Wellington
Auckland 1060
Loading...