Black & Decker DR670 TYPE 1 Owner’s Manual
1/2 in. (13ram) HAMMER DRILL
iNSTRUCTiON A L
Catalog Number
DR670
Thank you for choosing Black & Decker!
Go to www.BlackandDecker.com/NewOwner
to register your new product.
PLEASE READ BEFORE RETURNING THIS
PRODUCT FOR ANY REASON:
IfyouhaveaquestionorexperienceaproblemwithyourBlack&Deckerpurchase,goto
HTTP:/,_VWW.BLACKANDDECKER.COM/INSTANTANSWERS
forinstantanswers24hoursaday.
Ifyoucan'tfindtheanswerordonothaveaccesstotheinternet,
call1-800-544-6986from8 a.m.to5 p.m.ESTMon.-- Fri.tospeakwithanagent.
Pleasehavethecatalognumberavailablewhenyoucall.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIV© DE pPERACION, CENTROS DE SERVlCIO Y POLIZA DE GARANTiA.
ADVERTENClA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
General Power Tool Safety Warnings
_WARNING! Read all safety warnings and instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power toot" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power toot.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power toots in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets willreduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock:
f) If operating a power tool in a damp location is unavoidable, use a ground fault
circuit interrupter (GFCl) protected supply,. Use of a GFCI reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energizing power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewe//ery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power toot. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. Ifdamaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This willensure that the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
• Wear ear protectors with impact drills. Exposure to noise can cause hearing toss.
• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
• Hold power tools by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live" and shock the operator.
• Use clamps or another practical way to secure and support the work piece to a
stable platform. Holding the work by hand or against your body leaves itunstable and
may lead to loss of control.
• Keep your hair, clothing, and gloves away from air vents. Air vents often cover
moving parts in which these items can be caught.
• Hold tool firmly with two hands (see figure A). Use auxiliary handle if provided. Loss
of control can cause personal injury.
• Hammer bits and tools get hot during operation. Wear gloves when touching them.
z_WARNING: Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
z_WARNING: Use of this tool can generate and/or disperse dust, which may
cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body.
z_WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
ANSI S12.6 ($3. 19) hearing protection
NIOSH/OSHA/MSHA respiratory protection
2_WARNING: Always wear proper personal hearing protection that conforms to
ANSI $12.6 (S3.19) during use. Under some conditions and duration of use, noise
from this product may contribute to hearing boss.
SAFETY GUiDELiNES - DEFiNiTiONS
It is important for you to read and understand this manual.
The information it contains relates to protecting YOUR SAFETY and PREVENTING
PROBLEMS. The symbols below are used to help you recognize this information.
Z_DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
z_ WARNING: Indicates a.potentially hazardous situation which, if not avoided, could
result in death or serious tnjury.
Z_ CAUTION: Indicates a.po.tentially hazardous situation which, if not avoided, may
result in minor or moderate tnjury.
C..AU.TION: U.sed withou! the safety ale.rt symbol.ind.icates a potentially hazardous
situation wnicn, iTnot avoided, may result in property damage.
The label on your tool may include the following symbols.
V .......................... volts
Hz ........................ hertz
min ........................ minutes
A.......................... amperes
W ........................ watts
,x, ...................... alternating
current
- - - ...................... direct current
[] .......................... Class II Construction
no ........................ no load speed
G ........................ earthing terminal
z_ ........................ safety alert symbol
.../min .................... revolutions or
bpm ..................... beats per minute
reciprocations per minute
Extension Cords
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord wilt cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on
cord length and nameplate ampere rating. Ifin doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gauge
Than Than
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
Minimum Gauge for Cord Sets
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
(0-15,2m) (15,2-30,4m)(30,4-60,9m)(60,9-91,4m)
FUNCTIONAL DESCRIPTION
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode Selector
5. Side handle
6. Keytess chuck
7. Spindle lock button
8. Depth stop
Safety Warnings and instructions: Drills
Z_WARNING: Shock hazard. When drilling or driving into walls, floors or wherever
live electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF
THE TOOL! Hold the tool only by the plastic handle(s)/ housing to prevent shock.
• Do not lock the toot ON when drilling by hand. Refer to Operating Instructions-Switching
On and Off.
• Hold drill firmly with both hands to control the
twisting action of the drill (figure A). If your drill is
equipped with a side handle, always use the side
handle.
z_WARNING: Drill may stall (if overloaded or
improperly used) causing a twist. Always expect the
stall. Grip the drill firmly to control the twisting action
and prevent loss of control which could cause
personal injury. Ifa stall does occur, release the
trigger immediately and determine the reason for the
stall before re-starting.
• Always unplug the drill when attaching or removing accessories. When attaching
accessories in the drill chuck, it is important to securely tighten the chuck using all three
holes to prevent slippage. When using a keytess chuck, hand tighten firmly.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means
your drill will operate on standard 60 Hz household power. Do not operate AC tools on
DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC
or DC power. This information is printed on the nameplate. Lower voltage wilt cause loss
of power and can result in over-heating. All Black & Decker tools are factory-tested; if this
tool does not operate, check the power supply.
Assembly
Z_WARNING: To reduce the risk of injury, before assembly, make sure that the tool is
switched off and unplugged.
Attaching the side handle and depth stop -
(fig. B}
Your drill is equipped with a side handle, it must be
installed properly to control the drill.
• Turn the grip counterclockwise until you can slide the side
handle (5) onto the front of the toot as shown.
• Rotate the side handle into the desired position.
• Insert the depth stop (8) into the mounting hole as shown.
• Tighten the side handle by turning the grip clockwise.
• Be sure side handle is secure and will not rotate about the
tool. i i
Inserting a drill bit or other accessory (fig. C }
_WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping
the front part of the chuck and turning the tool on. Damage to the chuck and
personal injury may occur when changing
accessories.
z_WARNING: Always ensure the bit is
secure before starting the tool. A loose bit
may eject from tool causing possible
personal injury.
• Open the chuck by pressing the manual
spindle lock button (7) and turning the sleeve
(9) counter clockwise.
• Insert the bit shaft (10) into the chuck to about
3/4 in.(19 mm) depth, centered in the jaws.
• Firmly tighten the chuck by pressing the
manual spindle lock button (7) and turning
the sleeve (9) clockwise until it is tight.
Removing and attaching the chuck - (fig. D)
• Open the chuck (6) as far as possible.
• Remove the chuck retaining screw (11),
located in the chuck, by turning it clockwise
using a screwdriver (lefthand thread).
• Tighten an allen key (12) of 1/4in. (6mm) or
greater size (not supplied) into the chuck and
strike it with a soft hammer (13) in a
clockwise direction (when viewed from the
chuck end) as shown.
• Remove the allen key.
• Remove the chuck by turning it
counterclockwise.
• To attach the chuck, screw it onto the spindle
and secure it with the chuck retaining screw.
Operating Instructions
zEWARNING: To reduce the risk of serious personal injury, read, understand and
follow all safety warnings and instructions prior to using tool
_WARNING: It is important to support the work properly and to hold the drill
firmly to prevent loss of control which could cause personal injury, ffyou have any
questions on how to properly operate tool, call: 1=800-544-6986.
2_WARNING: Do not attempt to tighten drill bits (or any other accessory) by
gripping the front part of the chuck and turning the tool on. Damage to the chuck
and personal injury may occur when changing accessories.
z_WARNING: To reduce the risk of injury, always unplug drill from power supply
before making any adjustments or changing accessories.
2_WARNING: To reduce the risk of injury, let the tool work at its own pace. Do not
overload.
Selecting the direction of rotation - (fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
zEWARNING: Never change the direction of rotation
while the motor is running.
• To select forward rotation, push the forward/reverse
slider (3) to the left (when viewed from the chuck end).
• To select reverse rotation, push the forward/reverse
slider (3) to the right (when viewed from the chuck end).
Selecting the drilling mode
• For drilling in masonry, set the drilling mode selector (4)
to the "hammer symbol" [_ position.
• For drilling in other materials and for screwdriving, set the drilling mode selector (4) to the
"drill symbol" [_position.
O
Setting the drilling depth - (fig. F)
• Slacken the side handle (5) by turning the grip
counterclockwise.
• Set the depth stop (8) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
• Tighten the side handle by turning the grip clockwise.
Switching on and off
• To switch the tool on, press the variable speed switch
(1). The toot speed depends on how far you press the
switch. As a general rule, use low speeds for large
diameter drill bits and high speeds for smaller diameter drill bits.
• For continuous operation, press the lock-on button (2) and release the variable speed
switch. This option is available only at full speed in both forward and reverse direction.
• To switch the toot off, release the variable speed switch. To switch the toot off when in
continuous operation, press the variable speed switch once more and release it.
zkWARNING: The drill should only be locked ON when it is held stationary in a drill
press stand or other means; NOT BY HAND! Never unplug the toot with the locking
feature engaged. To do so will cause the tool to start immediately the next time it is
plugged in.
Drilling
• Always unplug the drill when attaching or removing accessories. When attaching
accessories in the drill chuck, it is important to securely tighten the chuck using all three
holes to prevent slippage. When using a keyless chuck, hand tighten firmly.
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the safety instructions.
• Use appropriate and required safety equipment, as instructed in the safety instructions.
• Secure and maintain work area, as instructed in the safety instructions.
• Plug in drill. Make sure switch turns drill on and off.
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the
drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting
but not so much as to stall the motor or deflect the bit.
• Hold the drill firmly with both hands to control its twisting action (figure A).
• Use side handle if drill is equipped with one.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON INAN ATTEMPT
TO START IT. DAMAGE TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the
last part of the hole.
• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.
Drilling In Wood
Holes in wood can be made with the same twist drill bits used for metal or with spade bits.
These bits should be sharp and should be pulled out frequently when drilling to clear
chips from the flutes.
Drilling In Metal
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which
should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
Drilling in Masonry (Shift drill into hammer mode)
Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but
not so much that you crack the brittle material. A smooth, even flow of dust indicates the
proper drilling rate.
Problem
• Unit will not start,
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
personnel, always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800=544-6986.
z_WARNING: The use of any accessory not recommended for use with this tool could
be hazardous.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service. Whether you need technical
advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. Tofind your local service location, refer to the yellow page directory under
"Tools--Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
FULL TWO=YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge
in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer's policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
Possible Cause
• Cord not plugged in.
• Forward/reverse slider not fully
depressed in desired direction.
• Circuit fuse is blown.
• Circuit breaker is tripped.
• Cord or switch is damaged.
9
Possible Solution
• Plug toot into aworking
outlet.
• Push slider completely to
the left or right.
• Replace circuit fuse.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Reset circuit breaker.
(If the product repeatedly
causes the circuit breaker
to trip, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Have cord or switch
replaced at Black &
Decker Service Center or
Authorized Servicer.
Troubleshooting
authorizedServiceCenterforrepairorreplacementatouroption.Proofofpurchasemay
berequired.Black&DeckerownedandauthorizedServiceCentersarelistedunder
"Toots-Electric"intheyellowpagesofthephonedirectory.
Thiswarrantydoesnotapplytoaccessories.Thiswarrantygivesyouspecificlegalrights
andyoumayhaveotherrightswhichvaryfromstatetostateorprovincetoprovince.
Shouldyouhaveanyquestions,contactthemanagerofyournearestBlack&Decker
ServiceCenter.Thisproductisnotintendedforcommercialuse.
FREEWARNINGLABELREPLACEMENT:Ifyourwarninglabelsbecomeillegibleorare
missing,call1-800=544=6986forafreereplacement.
LATINAMERICA:ThiswarrantydoesnotapplytoproductssoldinLatinAmerica.For
productssoldinLatinAmerica,checkcountryspecificwarrantyinformationcontainedin
thepackaging,callthelocalcompanyorseethewebsiteforwarrantyinformation.
MAXIMUM RECOMMENDED CAPACITIES
Cat. # Type Steel Soft Wood Hard Wood Mason_
DR670
1/2in. Hammer Drill 1/2in.(12.7mm) Twist Bit 1-1/2in.(38.1mm) 1-1/4in.(31.7mm) 1/2in.(12.7mm)
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
See 'Tools=
Electric'
- Yellow Pages -
for Service &
Sales
10
MARTEAU PERFORATEUR AVEC MECHE DE
1/2po (13 ram)
MODE D'EMPLOI
Catalog Number
DR670
Merci d'avoir choisi Black & Decker!
Consulter le site Web
www.BiackandDeck er.com/NewOwner
pour enregistrer votre nouveau produit.
A LIRE AVANT DE RETOURNER CE PRODUIT
POUR QUELQUE RAISON QUE CE SOIT :
SidesquestionsoudesproblemessurgissentapresI'achatd'unproduitBlack&Decker,
consulterlesiteWeb
HTTPJ/WWW.BLACKANDDECKER.COM/INSTANTANSWERS
pourobtenirdesr@onsesinstantanement24heuresparjour.
Silar@onseestintrouvableouenI'absenced'ac@sa.I'lnternet,composerle
1-800-544-6986de8 ha 17h HNE,dulundiauvendredi,pourparleravecunagent.
P@red'avoirlenumerodecataloguesouslamainIorsdeI'appel.
11
Loading...