Black & Decker DR600 TYPE 1 Owner’s Manual

I//bBLACK DECKER

INSTRUCTIONMANUAL

Catalog Numbers DR200, DR210, DR220, DR300, DR400, DR402, DR500, DRCO0

IF YoU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PURCHASE,

CALL 1-800-54-HOW-TO (1-800-544-6986).

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONEI

IFYOU HAVE A SUGGESTION OR COMMENT,

GIVE US A CALLI YOUR FEEDBACK ISVITAL

TO THE SUCCESS OF BLACK & DECKER'S QUALITY

IMPROVEMENT PROGRAMI

KEY INFORMATION YOU SHOULD KNOW:

• Reversing drills must be switched into forward or reverse in order to operate. They will

not run with the switch control lever in the center position.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section

of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

SPECIFICSAFETYRULES

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact

hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Z_WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such

as those dust masks that are specially designed to filter out microscopic particles.

The label on your tool may include the following symbols.

V .......................... volts

Hz ........................ hertz

min ...................... minutes

.... .................... direct current

[] ........................ Class II Construction

Z_ ........................ safety alert symbol

Levierdecommandede r interrupteur

Palancadecontrol

Drillingposition

Modedeperoge

P0sici0ndetaladrad0

......L0ck-0nbutton

B0ut0ndeverr0uillage

B0t0nde encendid0permanente

A ........................ amperes

W ...................... watts

,x, ...................... alternating current

no ...................... no load speed

........................ earthing terminal

.../min ................ revolutions or

reciprocations per minute

Lever_ Levieri

Palancai

..........Hammeringposition

Modedepercussion

P0sici0nder0t0martill0

• Securely tighten chuck jaws using all three holes except with keyless chucks which should be securely hand tightened.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

VEAEL ESPA_OLEN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTiA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

GENERALSAFETYRULES

Z_WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICALSAFETY

• Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.

Double insulation [] eliminates the need for the three wire grounded power cord and grounded power supply system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock.

PERSONALSAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing,jewelry, or long hair can be caught in moving parts.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USEAND CARE

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the

work by hand or against your body is unstable and may lead to loss of control. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer

at the rate for which it is designed. Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is

dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

• When drilling or driving into walls, floors or wherever live electrical wires may be encountered, DO NOT

TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the plastic handle to prevent shock.

• Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.

• Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a side handle, always

use the side handle.

Z_WARNING: Use of this tool can generate dust containing chemicals known to cause cancer, birth defects or

other reproductive harm. Use appropriate respiratory protection.

z_WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip

the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

• Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a

keyless chuck, hand tighten firmly.

MOTOR

Your Black & Decker tool is powered by a Black & Decker-built motor. Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your drill will operate on standard 60 Hz household power. Do

not operate AC tools on DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can

result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.

USEOF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the tool - that is, proper wire size for various lengths of cord and heavy enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in line voltage resulting in loss of power and overheating. For proper size cords see chart below.

Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300 Ampere Rating

More Not more American Wire Gage Than Than

0 6 18 16 16 14 6 10 18 16 14 12

10 12 16 16 14 12 12 16 14 12 Not Recommended

Minimum Gage for Cord Sets

ASSEMBLY/ADJUSTMENT SET-UP

_WARNING: Always unplug drill from power supply before any of the following operations.

SIDEHANDLE (1/2" DRILLSONLY)

• If your drill is equipped with a side handle, it must be installed properly in order to control the drill.

• Insert bolt into recessed hole with molded hex shape, making sure that hex head is seated fully to prevent bolt from turning.

• Place circular opening over drill chuck and onto front of drill gear case.

• Place the drill on its side and holding the bolt head with your finger, thread handle onto bolt. The handle now has a full range of 360 degrees around the drill.

OPERATING INSTRUCTIONS

_WARNING: To reduce the risk of serious personal injury, read, understand and follow all important

safety warnings and instructions prior to using tool.

SWITCH

To turn the drill ON squeeze the trigger switch. The farther the trigger is depressed, the higher the speed of the drill. To turn the tool OFF release the trigger switch. The drill can be locked ON (maximum RPM only) for continuous use by squeezing the trigger while pushing in on the locking button (Fig. 1). Hold the locking button

in while you release the trigger switch and then release the locking button. The drill will continue to run. To turn

the drill OFF from a locked ON condition, squeeze and release the trigger.

_WARNING: The drill should only be locked ON when it is held stationary in a drill press stand or other

means; NOT BY HAND! Never unplug the tool with the locking feature engaged. To do so will cause the tool to start immediately the next time it is plugged in.

FORWARD/REVERSE(DR200, DR210, DR220, DR300, DR400, DR402, DR600)

To select forward rotation push the switch control lever to the RIGHT (when viewed from the chuck end) (Fig. 1). To select reverse push the lever to the LEFT (when viewed from the chuck end). After all reversing operations,

switch the tool to the forward running mode.

NOTE: WHEN THE SWITCH CONTROL LEVER IS IN THE CENTER POSITION THE DRILL WILL NOT OPERATE. DO NOT FORCE TRIGGER. SELECT FORWARD OR REVERSE BEFORE TURNING DRILL ON.

FORWARD/REVERSE(DR500 ONLY)

To select forward rotation push the switch control lever to the LEFT(when viewed from the chuck end) (Fig. 1). To select reverse push the lever to the RIGHT (when viewed from the chuck end). After all reversing operations, switch the tool to the forward running mode.

NOTE: WHEN THE SWITCH CONTROL LEVER IS IN THE CENTER POSITION THE DRILL WILL NOT OPERATE.

DO NOT FORCE TRIGGER. SELECTFORWARD OR REVERSEBEFORETURNING DRILLON.

CHUCK & KEY OPERATION (DR200, DR400, DR500, DR600)

Turn chuck collar to open chuckjaws. Place bit in chuck as far as it will go. Tighten chuck collar by hand. Place chuck key ineach of the three holes, and tighten in clockwise direction (Fig. 2). Tighten chuck with all three holes to prevent slippage.

KEYLESSCHUCK OPERATION(DR210, DR220, DR300, DR402)

DR220 - Single Sleeve Chuck with Automatic Spindle Lock -This tool is equipped with a feature that automatically locks the spindle when the tool is not running. This anti-rotational feature is a normal condition

which allows for tightening or loosening of the chuck with one hand operation. Loosen the chuck by rotating the sleeve counterclockwise (Fig. 3). Insert the bit or other accessory fully into the chuck, and tighten securely by rotating the sleeve in the clockwise direction as viewed from the chuck end.

DR210, DR300, DR402 - To attach accessories, grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction. Insert the bit or other accessory fully into the

chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end.

HAMMER ACTION (DR400, DR402, DR600)

Your drill has hammer action which is engaged by sliding the hammer/drill selector lever. To select hammering, turn off the drill and rotate the lever shown in Figure 4 so that the arrow on the lever points to to the hammer symbol on the drill housing. To select drilling, turn off the drill and rotate the lever so that the arrow on the lever

oints to the drill symbol.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of

the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.

DRILLING

• Always unplug the drill when attaching or removing accessories, when attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly..

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the safety instructions.

• Secure and maintain work area, as instructed in the safety instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly to control its twisting action..

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

• Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The lubricants that work best are sulphurized cutting oil or lard oil. Bacon grease will also serve.

• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear chips from the flutes.

• Plug in drill. Make sure switch turns drill on and off.

KEYLESSCHUCK REMOVAL(DR210, DR220, DR300, DR402)

UNPLUG DRILL. Tighten the chuck around the shorter end of a hex key (not supplied) of 1/4" (6.4mm) or greater size. Using a soft hammer, strike key sharply in a counterclockwise direction (when viewed from the front of the tool). This will loosen the chuck so that it can be unscrewed by hand.

KEYEDCHUCK REMOVAL (DR200, DR400)

UNPLUG DRILL. NOTE: Before attempting to remove chuck, shift the drill into the drilling mode (not hammer, if so equipped ).

Place chuck key in any one of the three holes in the chuck. Strike the key sharply in a counterclockwise direction (when viewed from the front of the tool). This will loosen the chuck so that it can be removed by hand.

KEYEDCHUCK REMOVAL (DR500, DR600)

UNPLUG DRILL.

NOTE: Before attempting to remove chuck, shift the drill into the drilling mode (not hammer, if so equipped). Place chuck key in any one of the three holes in the chuck. Using a soft hammer, strike the key in a clockwise

direction. This will loosen the screw inside the chuck. Open chuck jaws fully, insert screwdriver (or Torx tool if required) into front of chuck between jaws to engage screw head. Remove screw by turning clockwise (left- hand-thread). Place key in chuck. Using a soft hammer, strike key sharply in a counterclockwise direction. This will loosen the chuck so that it can be unscrewed by hand.

Z_WARNING: t is important to support the work properly and to hold the drill firmly to prevent loss of

control which could cause personal injury If you have any questions on how to properly operate tool, call: 1-800-54-HOW-TO (544-6986).

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.

DRILLING IN METAL

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil; bacon grease will also serve the

purpose.

DRILLING IN MASONRY (Shift drill into hammer mode as shown in Fig. 4)

Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not so much that you crack the brittle material. A smooth, even flow of dust indicates the proper drilling rate.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO (544-6986).

z_WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

SERVICEINFORMATION

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with

efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker

location nearest you. To find your local service location, refer to the yellow pages directory under "Tools--

Electric" or call: 1-800-54-HOW-TO (544-6986).

FULLTWO-YEAR HOME USEWARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer's

policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and

authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory. This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have

other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. These products are not intended for commercial use.

MAXIMUM RECOMMENDED CAPACITIES

Cat. # Type Steel

DR200 3/8"Drill 3/8"(9.5mm) Twist Bit DR210 3/8"Drill 3/8"(9.5mm) Twist Bit DR220 3/8"Drill 3/8"(9.5mm) Twist Bit DR300 3/8"Drill 3/8"(9.5mm) Twist Bit

DR400 3/8"Hammer Drill 3/8"(9.5mm) Twist Bit 1-1/4"(31.7mm) 1"(25.4mm) 3/8"(9.5mm) DR402 3/8"Hammer Drill 3/8"(9.5mm) Twist Bit 1-1/4"(31.7mm) 1"(25.4mm) 3/8"(9.5mm)

Soft Wood Hard Wood Masonry

1-1/4"(31.7mm) 1"(25.4mm) N/A 1-1/4"(31.7mm) 1"(25.4mm) N/A 1-1/4"(31.7mm) 1"(25.4mm) N/A 1-1/4"(31.7mm) 1"(25.4mm) N/A

DR500 1/2"Drill 1/2"(12.7mm) Twist Bit 1-1/2"(38.1mm) 1-1/4"(31.7mm) N/A DR600 1/2"Hammer Drill 1/2"(12.7mm) Twist Bit 1-1/2"(38.1mm) 1-1/4"(31.7mm) 1/2"(12.7mm)

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

See 'Tools-Electric'

- Yellow Pages -

for Service & Sales

GUIDED'UTILISATION

ModUles DR200, DR210, DR220, DR300,DR400, DR402, DRS00 et DR600

RENSEIGNEMENTS IMPORTANTS

•/es perceuses dotees d'un inverseur de marche do|vent etre en position de marche avant ou art|ere pour fonctionner. La perceuse ne fonctionne pas Iorsque le levier de commande de I'interrupteur se trouve a la position centrale.

• Bien serrer les m_choires du mandrin darts chacun des trois trous, saul les mandrins sans cle qui se serrent fermement a la main.

MESURESDESI_CURITI_

z_ AVERTISSEMENT : Lire et comprendre routes les directives. Le non-respect de routes les directives

suivantes presente des risques de secousses electriques, d'incendie ou de blessures graves.

CONSERVER CES MESURES.

ZONE DETRAVAIL

• S'assurer que la zone de travail est propre et bien eclairee. Des etablis encombres et des endroits sombres presentent des risques d'accidents.

• Ne pas utiliser des out|Is electriques en presence de vapeurs explosives (comme celles degagees par des

liquides, des gaz ou des poussieres inflammables). Les etincelles generees par le moteur des out|Is electriques peuvent enflammer les poussieres ou les vapeurs.

• I_loigner les curieux, les enfants et les visiteurs de la zone de travail Iorsqu'on utilise un outil electrique. Une distraction peut entrainer la perte de maitrise de I'outil.

MESURESDESI_CURITI_RELATIVESis,L'I_LECTRICITI_

• Les outils a double isolation comportent une fiche polarisee (une lame plus large que I'autre). La fiche

n'entre que d'une fa_;on dans une prise polarisee. Lorsque la fiche n'entre pas a fond dans la prise, essayer de nouveau apres avoir inverse les broches de la fiche. Si la fiche n'entre toujours pas dans la

prise, communiquer avec un electricien certifie afin de faire installer une prise polarisee. Ne modifier en

aucune fad:on la fiche. La double isolation [] elimine le besoin d'un cordon trifilaire mis a la terre et d'un

systeme d'alimentation mis a la terre.

• I_viter de toucher ,_des surfaces mises ,_ la terre comme des tuyaux, des radiateurs, des cuisinieres et des

refrigerateurs. Les risques de secousses electriques sont plus eleves si le corps de I'utilisateur est mis a la terre.

• Proteger les out|Is electriques de la pluie ou des conditions mouillees. Une infiltration d'eau dans I'outil

augmente les risques de secousses electriques.

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter I'outil ni tirer sur le

cordon pour debrancher I'outil. I_loigner le cordon des sources de chaleur, des flaques d'huile, des arOtes tranchantes et des pieces mobiles. Remplacer immediatement les cordons endommages. Les cordons endommages augmentent les risques de secousses electriques.

• Lorsqu'on utilise un outil electrique ,_ I'exterieur, se servir d'un cordon de rallonge prevu pour I'exterieur, portant la mention "W-A" ou "W". Ces cordons sont con(;:us pour servir a I'exterieur et minim|sent les risques de secousses electriques.

SI[CURITI[PERSONNELLE

• Demeurer vigilant, prendre soin et fake preuve dejugement Iorsqu'on utilise un outil electrique. Ne pas

s'en servir Iorsqu'on est fatigue ou affaibli par des drogues, de I'alcool ou des medicaments. De graves

blessures peuvent resulter d'un moment d'inattention Iors de I'utilisation d'un outil electrique.

• Porter des vOtements appropries. I_viter de porter des vOtements amples ou des bijoux. Recouvrir la

chevelure si elle est Iongue. Eloigner les cheveux, les vOtements et les gants des pieces en mouvement qui

peuvent les happer.

• I_viter les demarrages accidentels. S'assurer que I'interrupteur est en position hors tension avant de brancher I'outil. Afin d'eviter les risques de blessures, ne pas transporter I'outil avec le doigt sur I'interrupteur ni brancher un outil dont I'interrupteur est en position sous tension.

• Enlever les dos de reglage avant de mettre I'outil sous tension. Une cle qui est laissee sur une piece rotative

de I'outil presente des risques de blessures.

• Ne pas depasser sa portee. Carder son equilibre en tout temps. On s'assure d'une meilleure maitrise de I'outil dans des situations imprevues grace a une position stable et un bon equilibre.

• Porter de I'equipement de securit& foujours porter des lunettes de securit& Dans certaines conditions, il

faut porter des masques respiratoires, des chaussures antiderapantes, un casque de securite ou des protege- tympans.

UTILISATIONETENTRETIENDEL'OUTIL

• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de soutenir la piece ,_ouvrer

sur une plate-forme stable. La piece est instable Iorsqu'elle est retenue par la main ou le corps de I'utilisateur.

Cela presente des risques de perte de maitrise de I'outil.

• Ne pas forcer I'outil. Utiliser I'outil approprie ,_ la t,_che. L'outil approprie fonctionne mieux et sOrement Iorsqu'on s'en sert a son rendement nominal.

• Ne passe servir de I'outil Iorsque I'interrupteur est defectueux. Le cas echeant, I'outil est dangereux et il

faut le reparer.

• Debrancher I'outil de la source d'alimentation avant de le regler, d'en remplacer les accessoires ou de le

ranger. On rain|raise de la sorte le risque de demarrage accidentel de I'outil.

• Ranger I'outil hors de portee des enfants et de toute autre personne qui n'en connait pas le

fonctionnement. L'outil est dangereux entre les mains de ces personnes.

• Prendre soin des out|Is. S'assurer que les out|Is de coupe sont tranchants et propres. Des out|Is bien

entretenus a aretes tranchantes ont moins tendance a se coincer et |Is se maitrisent mieux.

• Verifier I'alignement et les attaches des pieces mobiles, le degre d'usure des pieces ainsi que tout autre

facteur susceptible de nuire au bon fonctionnement de I'outil. Fake reparer un outil endommage avant de s'en servir. Des out|Is real entretenus sont la cause de nombreux accidents.

• Utiliser seulement les accessoires recommandes par le fabricant. Des accessoires qui conviennent a un outil peuvent presenter des risques avec un autre outil.

ENTRETIEN

• Confier I'entretien de I'outil seulement ,_ du personnel qualifie. Le non-respect de la presente directive presente des risques de blessures.

• Lots de I'entretien de I'outil, utiliser seulement des pieces de rechange identiques. Respecter les consignes

relatives ,_ I'entretien du present guide d'utilisation. II y a risque de secousses electriques ou de blessures

Iorsqu'on utilise des pieces non autorisees ou Iorsqu'on ne respecte pas les consignes relatives a I'entretien.

MESURESDESI[CURITI[ADDITIONNELLES

• Saisir les surfaces isolees de I'outil Iorsqu'on s'en sert I,_ ou il pourrait y avoir des fils sous tension et

Iorsqu'il pourrait entrer en contact avec son propre fil. En cas de contact avec un fil sous tension, les composantes metalliques a decouvert de I'outil deviendraient sous tension et I'utilisateur subirait des secousses electriques.

Z_AVERTISSEMENT : Certains out|Is, tels que les sableuses electriques, les scies, les meules, les perceuses ou

certains autres out|Is de construction, peuvent soulever de la poussiere contenant des produits chimiques susceptibles d'entrainer le cancer, des malformations congenitales ou pouvant etre nocifs pour le systeme reproductif. Parmi ces produits chimiques, on retrouve :

• le plomb dans les peintures a base de plomb;

• la silice cristalline dans les briques et le ciment et autres produits de ma(;:onnerie;

• I'arsenic et le chrome dans le bois de sciage ayant sub| un traitement chimique.

Le risque associe a de telles expositions peut varier selon la frequence avec laquelle on effectue ces travaux. Pour reduire I'exposition a de tels produits, il faut travailler dans un endroit bien ventile et utiliser I'equipement

+ 3 hidden pages