Black & Decker BX560-B5, BX580-B5 User Manual
www.blackanddecker.ae
BX560-B5 / BX580-B5
ENGLISH
Parts Identification
A. Filler Cap
B. Lid
C. Blender Jug
D. Jug Base
E. Jug Seal
F. Blade
G. Blade Holder
H. Motor Coupling
I. Blender Body
J. Control Knob
K. Mincer Jug
(BX580 Only)
L. Mincer Blade
(BX580 Only)
M. Mincer Blade Holder
(BX580 Only)
N. Grinder Jug
O. Grinder Blade
P. Grinder Blade Holder
Q. Grinder / Mincer Seal
2
ENGLISH
Intended use
Your Black & Decker blender has been designed
for blending, mixing and crushing of solid and
liquid food and beverage ingredients. This
product is intended for indoor household use
only.
Read this entire manual carefully
before using the appliance.
Safety instructions
• Warning! When using mains-powered
appliances, basic safety precautions,
including the following, should always be
followed to reduce the risk of fire, electric
shock and personal injury.
• The intended use is described in this manual.
The use of any accessory or attachment or
the performance of any operation with this
appliance other than those recommended in
this instruction manual may present a risk of
personal injury.
• Retain this manual for future reference.
Using your appliance
• Always take care when using the appliance.
• Never pull the power supply cord to
disconnect the plug from the socket. Keep
the power supply cord away from heat, oil
and sharp edges.
• Do not place the appliance on or near heat
sources or in a heated oven.
• Do not use the appliance outdoors.
• Always protect the motor unit from water or
excessive humidity.
• If the power supply cord is damaged during
use, disconnect the appliance from the
power supply immediately. Do not touch the
power supply cord before disconnecting from
the power supply.
• Disconnect the appliance from the power
supply when not in use, before fitting or
removing parts and before cleaning.
• Never let the appliance operate unattended.
• Never reach into the jar with your fingers or
an object while the appliance is running.
• Only remove the jar after you have switched
the appliance off and any moving parts have
stopped.
• Do not touch the cutting blades.
• Keep any loose clothing or long hair away
from the feeding tube and any moving parts.
• Care shall be taken when handling the sharp
cutting blades, emptying the bowl and during
cleaning.
• Do not immerse the appliance, cord set or
plug in liquids.
Safety of others
• This appliance is not intended for use by
persons (including children) with reduced
physical sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
After use
• Remove the plug from the socket before
leaving the appliance unattended and before
changing, cleaning or inspecting any parts of
the appliance.
• When not in use, the appliance should be
stored in a dry place. Children should not
have access to stored appliances.
3
ENGLISH
Inspection and repairs
• Switch off the appliance before cleaning,
changing accessories or approaching parts
which move in use
• Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches and
any other conditions that may affect its
operation.
• Do not use the appliance if any part is
damaged or defective.
• Do not use the appliance if the blade is
damaged.
• Have any damaged or defective parts
repaired or replaced by an authorised repair
agent.
• Before use, check the power supply cord for
signs of damage, ageing and wear.
• Do not use the appliance if the power supply
cord or mains plug is damaged or defective.
• If the power supply cord or mains plug is
damaged or defective it must be repaired by
an authorised repair agent in order to avoid a
hazard. Do not cut the power supply cord
and do not attempt to repair it yourself.
• Never attempt to remove or replace any
parts other than those specified in this
manual.
Electrical safety
Before use, check that the mains voltage
corresponds to the voltage on the rating plate.
This appliance is double insulated in
accordance with EN 60335-2-14;
therefore no earth wire is required.
• To avoid the risk of electric shock, do not
immerse the cord, plug or motor unit in water
or other liquid.
• Check that the supply voltage shown on the
rating plate of the appliance matches that of
your electrical system. Any connection error
will invalidate the guarantee.
Mains plug replacement
If a new mains plug needs to be fitted:
• Safely dispose of the old plug
• Connect the brown lead to the live terminal of
the new plug
• Connect the blue lead to the neutral terminal
• If the product is class I (earthed), connect the
green/yellow lead to the earth terminal
Warning! If your product is class II double
insulated (only 2 wires in the cord set), no
connection is to be made to the earth terminal
• Follow the fitting instructions supplied with
good quality plugs
• Any replacement fuse must be of the same
rating as the original fuse supplied with the
product
Assembly
1. Wash all detachable parts (see chapter
‘Maintenance and cleaning’).
2. For the blender, fit the seal (E) on to the
blade holder (G).
3. Place the blade holder (G) into the jug base
(D) and secure buy turning anti-clockwise.
4. Place the filler (A) cap into the lid (B) and
secure by turning it clockwise.
5. Place the lid (B) on to the jug (C) and secure
it by turning clockwise.
6. For the grinder, fit the jug seal (Q) into the
groove around the edge of the grinder jug
(N).
4
ENGLISH
7. For the mincer, fit the mincer seal (Q) into the
groove around the edge of the mincer jug
(K).
8. Secure the blade holder (P or M) into the
required jug by pushing it into the jug and
turning it clockwise.
9. Fit the blender jug (C), grinder jug (N) or
mincer jug (K) to the blender body (I) by
turning it clockwise.
Use
1. Place the appliance on a flat, stable surface.
2. Put the ingredients into the required jug (C, K
or N).
3. If using the blender push the lid (B) and filler
cap (A) onto the jug (C). The filler cap and lid
are secured by turning them clockwise.
4. If using the grinder or mincer seal the jug by
fitting the required blade holder (P or M) and
secure by turning clockwise.
5. Place the jug (C, N or K) onto the blender
body (I).
6. Secure the jug (C, K or N) by turning it anti
clockwise.
7. Connect it to the electrical supply and select
the required speed using the rotary switch.
The following settings are available:-
P = Pulse Operation
O = Power Off
1 = Low Speed
2 = Low to medium speed
3 = Medium speed
4 = Medium to high speed
5 = High Speed
The appliance should be disconnected
from the mains supply before removing
the jug.
Recommendations when
blending
Ingredients Max Run Time Speed Max Quantity
(Seconds) (ml)
Liquids 60 sec 3 to 5 1.25L
Semi
Liquids 30 sec 1 to 3 0.75 to 1.5L
*Semi Liquids assumes maximum of 250 grams
of fruits, vegetables or ice in 2.5x2.5 cm cubes
along with 500 ml of water or any other liquid of
similar consistency.
Note: The blender should not be run for longer
than 3 minute. After a continuous run of 3
minutes, the blender should be allowed to cool
down for at least 10 minutes before further use.
Recommendations when
grinding
Ingredients Max Run Time Speed Max Quantity
(Seconds) (g)
Dry Pepper/
Coffee beans
Dry Pulses 30 sec 1 50g
Dry Herbs 20 sec 1 50g
Note: The dry grinder should not be run for
longer than 1 minute. After a continuous run of 1
minute, the blender should be allowed to cool
down for at least 10 minutes before further use.
Warning! The grinder should NOT be used for
wet grinding of hard food materials like pulses,
beans, grains etc. This will lead to damage of
blades and reduction of motor life span.
20 sec 2 60g
5
ENGLISH
Recommendations when
mincing (BX580 Only)
Ingredients Max Run Time Speed Max Quantity
(Seconds) (g)
Ginger 60 sec 1 30g
Meat ** 10 sec 1 50g
Cheese * 10 sec 2 50g
* The mincer should only be used for very hard
cheeses such as parmesan.
** Meat should be thawed, boneless, skinless &
a maximum cube size of 2x3 cm
Note: The mincer should not be run for longer
than 1 minute. After a continuous run of 1
minute, the blender should be allowed to cool
down for at least 10 minutes before further use.
Useful advice
Note: Do not exceed the maximum capacity of
1.5 litres.
• When blending is complete return the control
knob to the off (0) position.
• Once the blade has come to a complete
stop, lift the jug (D) from the blender body (I).
• Remove the lid (B) and pour the ingredients
into a suitable container.
• Liquids can be poured through the pouring
spout (C) by lifting the spout cover.
Note: Ingredients can be added by inserting
them through the hole left when the filler cap (A)
is removed.
Warning! Never operate the Blender without
the lid (B) fitted.
Warning! Do not use any of the accessories
with out the required seal.
Maintenance & cleaning
• Switch the appliance off, remove the plug
from the wall socket and wait until the blade
has stopped rotating.
• The appliance is easier to clean if you do so
immediately after use.
• Do not use abrasive cleaning agents,
scourers, acetone, alcohol etc. to clean the
appliance.
• All detachable parts are dishwasher-safe.
• Place the detachable plastic parts on the top
tray of the dishwasher. Make sure they are
placed well away from the heating element.
• All removable parts can be cleaned with a
cleaning brush in warm water with some
washing-up liquid and rinse them under the
tap.
• Remove the dirty parts from the motor unit.
Clean the motor unit with a damp cloth.
• Never immerse the motor unit in water nor
rinse it under the tap.
Technical data
BX560, BX580
Voltage 220 – 240 Volts
Supply 50/60 Hz
Power consumption 500W
6
ENGLISH
Protecting the environment
Separate collection. This product must not
be disposed of with normal household
waste.
Should you find one day that your Black &
Decker product needs replacement, or if it is of
no further use to you, do not dispose of it with
other household waste. Make this product
available for separate collection.
• Black & Decker provides a facility for
recycling Black & Decker products once they
have reached the end of their working life.
This service is provided free of charge. To
take advantage of this service please return
your product to any authorised repair agent
who will collect them on our behalf.
• You can check the location of your nearest
authorised repair agent by contacting your
local Black & Decker office at the address
indicated in this manual. Alternatively, a list of
authorized Black & Decker repair agents and
full details of our after-sales service and
contact are available on the Internet at:
www.2helpU.com.
Warranty
Black & Decker is confident of the quality of its
products and offers an outstanding warranty.
This warranty statement is in addition to and in
no way prejudices your statutory rights.
The warranty is valid within the territories of the
Member States of the European Union and the
European Free Trade Area.
If a Black & Decker product becomes defective
due to faulty materials, workmanship or lack of
conformity, within 24 months from the date of
purchase, Black & Decker warranty to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
The product has been used for trade,
professional or hire purposes;
The product has been subjected to misuse
or neglect;
The product has sustained damage
through foreign objects, substances or
accidents;
Repairs have been attempted by persons
other than authorised repair agents or
Black & Decker service staff.
To claim on the warranty, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting
your local Black & Decker office at the address
indicated in this manual.
Alternatively, a list of authorised Black & Decker
repair agents and full details of our after-sales
service and contacts are available on the Internet
at: www.2helpU.com.
7
Loading...