Page 1
www.blackanddecker.com.au.
2
1
4
3
Australia
New Zealand
Page 2
2
C D
B
A
6 7 5
4 7
8
3
9
Page 3
3
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool for damage. Check for
misalignment and seizure of moving parts, breakage of parts,
damage to guards and switches and any other conditions that
may affect its operation. Ensure that the tool will operate
properly and perform its intended function. Do not use the tool
if any part is damaged or defective. Do not use the tool if the
switch does not turn it on and off. Have any damaged or
defective parts repaired or replaced by an authorised repair
agent. Never attempt any repairs yourself.
Remove the battery
Where the design permits, remove the battery when the tool
is not in use, before changing any parts of the tool,
accessories or attachments and before servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when inserting the battery
into the tool.
Do not abuse cord
Never carry the charger by its cord or pull it to disconnect from
the socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools, batteries and chargers should be
stored in a dry, locked up or high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.
Repairs
This tool complies with relevant safety requirements. Repairs
should only be carried out by qualified persons using original
spare parts; otherwise this may result in considerable danger
to the user.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
Do not expose the battery to water.
Do not store in locations where the temperature may
exceed 40 °C.
Intended use
Your Black & Decker cordless blower has been designed for
blowing leaves and debris. This tool is intended for consumer
and outdoor use only.
Your Black & Decker charger has been designed for charging
Black & Decker batteries of the type supplied with this tool.
Safety instructions
Warning! When using battery-powered tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, leaking batteries,
personal injury and material damage.
Read all of this manual carefully before operating the tool.
Retain this manual for future reference.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the tool
where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn.
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense. Do not operate
the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
Page 4
4
Charge only at ambient temperatures between 4 °C
and 40 °C.
Charge only using the charger provided with the tool.
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Under extreme conditions, battery leakage may occur.
When you notice liquid on the battery, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
- In case of skin or eye contact, follow the instructions
below.
Warning! The battery fluid, a 25-30% solution of potassium
hydroxide, can be harmful. In case of skin contact, immediately
rinse with water. Neutralise with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with
clean water for at least 10 minutes. Consult a physician.
Do not incinerate the battery.
Do not attempt to charge damaged batteries.
Chargers
Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
$
The charger is intended for indoor use only.
Electrical safety
#
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate.
Never attempt to replace the charger unit with
a regular mains plug.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Switch the tool off. Before performing any
maintenance on the tool, remove the battery from
the tool.
Additional safety instructions for blowers
Warning! Do not point the tool at persons or animals when it
is switched on.
F
Wear safety glasses or goggles when operating
this tool.
Use a face or dust mask whenever the operations take
place in dusty surroundings.
Do not expose the tool to rain or high humidity.
Do not place outlet tubes near eyes or ears when
operating.
Do not cross gravel paths or place the tool on gravel
while the tool is switched on.
Do not place any objects into the openings and moving
parts.
Before removing the blow tube, always switch off the tool,
remove the battery and allow the tool to run down.
Read the instructions carefully. Be familiar with the
controls and the proper use of the appliance.
Do not allow children or any person unfamiliar with these
instructions to operate the appliance. Local regulations
may restrict the age of the operator.
Never use the appliance while people, especially children,
or pets are nearby.
Remember that the operator will be held responsible for
accidents or hazards occurring to other people or their
property.
Preparation
Do not operate your product barefoot or in open sandals.
To protect your feet and legs, always wear stout shoes or
boots and long trousers - freshly cut grass is damp and
slippery. Rubber or man made footwear will enhance your
safety.
Warning! Only use the tool in the manner it was intended.
Overview
1. On/off switch
2. Handle
3. Blow tube
4. Battery
Fig. A
5. Charger
6. Charging indicator
7. End of charge indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Page 5
5
Fitting and removing the battery (fig. B)
To fit the battery (4), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (7) while
at the same time pulling the battery out of the receptacle.
Connecting the blow tube (fig. C)
Blow tube must be assembled to the blow clamshell before use.
Align the circles (8) on the clamshell (9) and the tube (3).
Push the tube firmly onto the clamshell until the circles
click into place.
For storage the blow tube can be detached from the blow
clamshell by depressing the circles on either side and
gently sliding off the tube.
Use
Warning! Let the tool work at its own pace. Do not overload.
To charge the battery (4), remove it from the tool and
insert it into the charger (5). The battery will only fit into
the charger in one way. Do not force. Be sure that the
battery is fully seated in the charger.
Plug in the charger.
1 hour charger
Check if the red charging indicator (6) lights up. If the
green end of charge indicator (7) lights up now instead,
the battery is too hot and cannot be charged. If this
happens, remove the battery from the charger, let the
battery cool down for approx. 1 hour and re-insert it.
After approx. 1 hour of charging, the red charging indicator will
stop lighting and the green end of charge indicator will light
up. The battery is now fully charged.
Remove the battery from the charger.
Switching on and off
To switch the tool on, press the on/off switch (1).
To switch the tool off, release the on/off switch.
Hints for optimum use
Hold the blow tube approx. 180 mm above the ground
when operating the tool.
Use a sweeping motion from side to side. Advance slowly
keeping the accumulated debris/leaves in front of you (fig. D).
After blowing the debris/leaves into a pile, it is easy to
dispose of the pile.
Cleaning the tool
Clean the tool regularly.
Warning! Keep your product dry. Under no circumstances
spray with water.
To clean the tool, use only mild soap and a damp cloth.
Warning! Do not use any type of detergent, cleaner or solvent
which may contain chemicals that could seriously damage the
plastic.
Self lubricating bearings are used in your product,
therefore lubrication is not required.
Protecting the environment
Separate collection. This product must not be disposed
of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Reuse of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Batteries
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard batteries
with due care for our environment:
Page 6
6
Run the battery down completely, then remove it from the
tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
Technical data
BS118-XE
Voltage VDC 18
Weight (without battery) kg 2.2
Battery
Voltage VDC 18
Capacity Ah 1.5
Weight kg 0.8
Charger
Input voltage VAC 230
Approx. charging time h 1
Weight kg 0.4 0.4
EC declaration of conformity
BS118-XE
Black & Decker declares that these products conform to:
98/37/EC, 2006/95/EC, EN 50260, EN 61000, EN 60335
2000/14/EC, Leaf blower, 2.0 m3, Annex V
Level of sound pressure, measured according to 2000/14/EC:
LpA (sound pressure) 74 dB(A), uncertainty (K) 3 dB(A)
LWA (acoustic power) 88 dB(A), uncertainty (K) 3 dB(A)
LWA (guaranteed) 90 dB(A), uncertainty (K) 3 dB(A)
Hand/arm weighted vibration value according to
EN 60745 Annex K: 2.5 m/s
2
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-7-2008
AUSTRALIA AND NEW ZEALAND
Black & Decker welcomes you as a purchaser of this product
from our range of Home Products, Garden tools and Accessories.
All our products are engineered and manufactured to ensure the
highest standards of reliability and performance during use, and
are supported in After Sales Service by a wide network of
Black & Decker Authorised Service Centres.
2YEAR REPAIR GUARANTEE
BLACK & DECKER SUPPLEMENTARY
GUARANTEE
Subject to the conditions stated below, Black&Decker
guarantees that it will correct by repair or parts
replacement, without charge, any defect in the product
arising from faulty workmanship or materials where such
defect arises within two years from the date of purchase
of the product. A product subject to claim under this
guarantee should be returned as a complete unit to the
most convenient Black&Decker Authorised Service Centre
or Agent.
CONDITIONS.
The Black&Decker Supplementary Guarantee does not
apply in the following cases:
where the product has been used for trade or industrial
purposes:
where any defect or failure is attributed to accident,
misuse, abuse, negliance or non-observance of local
regulations on the part of the owner or user: or
where the product has been serviced by a person
not authorised by Black&Decker to do so, or with non
approved parts: or
to loose accessories.
In order to enforce the Black&Decker Supplementary
Guarantee, proof of purchase is required (purchase receipt).
The period of the Black&Decker Supplementary Guarantee
begins from the original date of purchase not withstanding
any subsequent repair or parts replacement. No guarantees
other than contained in this document, whether written
or verbal, are authorised to be made on behalf of
Black&Decker. All other conditions and guarantees
whether expressed or implied by law, are, to the extent
permitted by law, hereby excluded. The Black&Decker
Supplementary Guarantee does not apply outside
Australia and New Zealand.
PURCHASERS STATUTORY RIGHTS.
The Black&Decker Supplementary Guarantee set out
above does not exclude any conditions or guarantees
that may be manditorily implied by law, and your attention
is drawn to the provisions of the Consumer Guarantee
Act 1993 (New Zealand only), Trade practices Act 1974
and State legislation (Australia only), which confers
rights upon consumers. This is in addition to any rights
conferred on a consumer under the Act, where applicable and any other rights provided under applicable
legislation.
Page 7
TYP
1
WWW.2helpU.com 28-10-03B
B
S118-XE
1
3
4
2
5
6
7
8
9
10
11
12
15
14
13
16
17
Page 8
90541103 T-08/08
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark, Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker Tel. 0800 339 258
5 Te Apunga Place Fax +64 9 259 1122
Mt Wellington
Auckland 1060
Loading...