Black & Decker BPGS8115, BPGS7100, BPGS7115, BPGL2223 User Manual
BPGS8100
BPGS8115
www.blackanddecker.ae
ENGLISH
2
Figure 1
b
c
c
d
h
f
g
e
i
k
Figure 2 Figure 3
n
a
3
ENGLISH
Figure 5
Figure 6
Figure 4
h
f
d
e
15o-30
o
A B
4
ENGLISH
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
Danger: Indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
Warning: Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Caution: Indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Notice: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Warning: To reduce the risk of injury, read the
instruction manual.
General Power Tool Safety Warnings
Warning: Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in the
off position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
5
ENGLISH
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional specific safety rules
Safety Instructions for All Operations
a) This power tool is intended to function as a grinder. Read
all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to
follow all instructions listed below may result in electric
shock, fire and/or serious injury.
b) Operations such as cutting-off , sander, wire brush or
polisher are not recommended to be performed with this
power tool. Operations for which the power tool was not
designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannon be
adequately guarded or controlled.
f) The arbour size of wheels, flanges, backing pads or any
other accessory must properly fit the spindle of the power
tool. Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
6
ENGLISH
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheel for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury beyond
immediate area of operation.
j) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
k) Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your
control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents. The motor’s
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
o) Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
Further safety instructions for all operations
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding. For example, if an
abrasive wheel is snagged or pinched by the workpiece, the
edge of the wheel that is entering into the pinch point can
dig into the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of the
wheel’s movement at the point of pinching. Abrasive wheels
may also break under these conditions.Kickback is the result
of tool misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions
as given below:
a) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start up.
The operator can control torque reaction or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool
in direction opposite to the wheel’s movement at the
point of snagging.
7
ENGLISH
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and
loss of control.
Safety Warnings Specific for Grinding Operations
a) Use only wheel types that are recommended for your
power tool and the specific guard designed for the
selected wheel. Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power tool
and positioned for maximum safety, so the least amount
of wheel is exposed towards the operator. The guard
helps to protect operator from broken wheel fragments
and accidental contact with wheel and sparks that could
ignite clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with the side of
cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels
may cause them to shatter.
d) Always use undamaged wheel flanges that are of correct
size and shape for your selected wheel. Proper wheel
flanges support the wheel thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels may be
different from grinding wheel flanges.
e) Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
Tool Symbols
The following symbols are printed on the tool:
Read the instruction manual before use.
Please wear hearing protectors.
Please wear eye protection equipment.
Position of date barcode (fig. 1)
The date barcode (n), including the year of manufacturing, is
printed on the tool housing.
E.g.:
2013 XX JN
Year of manufacturing
Package Content
This product package includes:
1 Angle grinder
1 Guard
1 Flange set
1 Spanner
1 Handle
1 Instruction manual
• Check the tool, parts, and accessories to see if they are
damaged during transportation.
• Take a few moments to read and understand this
manual before using the tool.
Description (Fig. 1)
Warning! Never modify the power tool or any
part of the tool, otherwise it may cause
damage to the tool or result in personal injury.
a. ON/OFF switch
b. Spindle lock
c. Guard
8
ENGLISH
Purpose of design
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other than
those with depressed center.
Do not use the tool in wet conditions or environments in the
presence of flammable liquids or gases.
This heavy-duty angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool under
supervision.
Electrical Equipment Safety
Only one voltage is applicable to this tool. Be sure to check
that the power suuply corresponds to the voltage on the
rating plate.
Your Black & Decker tool is equipped with double
insulation, hence, it does not require to be earthed.
When the power cord is damaged, have it sent to a Black &
Decker service center for replacement to specially prepared
cables.
Using Extension Cords
If an extension cord is required, please select a 3-phase
extension cord that has been inspected and matches the
input power (see Technical Data) of this tool. The minimum
conductor size is 1.5mm2, maximum length is 30 meters.
When using a cable reel, be sure to pull out all the cables.
Assembly and Adjustment
Warning! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling the
tool, press and release the trigger switch to make sure the
tool is already switched off.
Attaching and Removing the Wheel Guard
(Fig. 2)
Warning! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling the
tool, press and release the trigger switch to make sure the
tool is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (c) collar over the groove (i)
of the gear housing.
3. Turn the guard (c) clockwise by 180 degrees.
4. Make sure that the screws (k) are tightened.
Removing the guard
1. Loosen the screws (k) on the guard collar.
2. Pull up the guard (c).
Warning! Do not operate the tool when the
safety guard is not in place.
Note: Refer to the grinding accessories chart at the end of
this section for accessories that can be used together with
this angle grinder.
Attaching and Removing Grinding Wheels (Fig. 3, 4)
Warning! Do not use damaged grinding wheels.
1. Place the tool on a work bench, groove facing up.
2. Attach the inner flange (d) correctly on the output shaft
(e) (Fig. 3).
3. Place the grinding wheel (f) on the inner flange (d).
When attaching a grinding wheel with a raised center,
make sure that the raised center (g) faces the inner
flange (d).
4. Tighten the outer flange (h) until the output shaft (e) (Fig.
4). When attaching the grinding wheel, the ring on top of
the outer flange (h) must face the wheel.
5. Press the spindle lock (b) and prevent the spindle (e)
from rotating until it locks in place.
6. Use the pin spanner to tighten the outer flange (h).
9
ENGLISH
Preparation Before Use
• Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
• Make sure that the inner and outer flanges are attached
correctly.
• Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the accessories
and tool.
Operation (Fig. 5)
Instructions
Warning! Always observe the safety
instructions and applicable regulations.
Warning! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling the
tool, press and release the trigger switch to make sure the
tool is already switched off.
Warning!
• Make sure all materials to be grinded are secured in
position.
• Apply slight pressure to the tool. Do not apply side
pressure to the abrasive disc. • Avoid overloading. If the
tool becomes hot, let it spin for a few minutes with no
load.
1. Be sure to hold the tool tightly with both hands (one
hand on housing, the other on side handle). Start the
tool and bring the grinding wheel on the workpiece.
2. Keep the edge of the wheel tilted at angle from 15 to 30
degrees against the surface of the workpiece.
3. When using a new grinding wheel, do not operate the
wheel in the B direction, otherwise, it will cut into the
workpiece. When the edge of wheel has been rounded
off, you are free to operate the grinder in either the A or
B direction.
Starting and Stopping (Fig. 1)
Warning! Before using the tool, check whether
the handle is tightened securely. Check whether
the ON/OFF switch is working normally.
Before plugging in the tool to the power supply, check
whether the switch is in the OFF (o) position when pressing
the rear end of the switch.
To start the tool, press the rear end of the switch and slide it
forward. Then press the front end of the switch to lock it.
Press the rear end of the switch to stop the tool.
Warning! Do not switch the tool on or off while
under load conditions.
Proper Hand Position (Fig. 6)
Warning! To reduce the risk of serious personal
injury, ALWAYS use proper hand position as
shown.
Warning! To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
(figure 1), with the other hand on the body of the tool, as
shown in figure 6.
Switches
Caution: Hold the body of the tool firmly to
maintain control of the tool at start up and during
use and until the wheel or accessory stops
rotating. Make sure the wheel has come to a complete stop
be fore laying the tool down.
Note: To reduce unexpected tool movement, do not switch
the tool on or off while under load conditions. Allow the
grinder to run up to full speed before touching the work
surface. Lift the tool from the surface before turning the tool
off. Allow the tool to stop rotating before putting it down.
Slider switch (fig. 1)
Warning! Before connecting the tool to a power
supply, be sure the slider switch is in the off
10
ENGLISH
position by pressing the rear part of the switch and
releasing. Ensure the slider switch is in the off position as
described above after any interruption in power supply to
the tool, such as the activation of a ground fault interrupter,
throwing of a circuit breaker, accidental unplugging, or
power failure. If the slider switch is locked on when the
power is connected, the tool will start unexpectedly.
To start the tool, slide the slider switch (a) toward the front of
the tool. To stop the tool, release the slider switch.For
continuous operation, slide the switch toward the front of the
tool and press the forward part of the switch inward. To stop
the tool while operating in continuous mode, press the rear
part of the slider switch and release.
Spindle lock (Fig. 1)
The spindle lock (b) prevents the output shaft from rotating
when attaching or removing the grinding wheel. Only use
the spindle lock when the tool is switched off, power is
unplugged, and wheel stops completely.
Note: To minimize tool damages, don't use the
spindle lock when the tool is operating.
Otherwise, it may damage the tool. The
attached accessories may come off and cause injury.
If using the spindle lock, press the spindle lock button and
rotate the output shaft until it stops.
Application on Metals
When applying the tool on metals, make sure that a
residual-current device (RCD) is inserted to prevent danger
from metal chips.
If the RCD causes power disconnection, have the tool sent
to an authorized Black & Decker dealer for repair.
Warning! Under extreme working conditions,
conductive dust and grit may accumulate on the
housing interior when handling metal
workpieces. This could create an electric shock hazard as it
weakens the protective insulation in the grinder.
To avoid accumulation of metal chips in the interior of the
grinder, we recommend cleaning the ventilation ducts daily.
Refer to Maintenance.
Using Grinding Wheels
Warning! Metal powder accumulates.
Excessive use of the grinding wheel on metals
may increase the risk of electric shock. To
reduce the risk, insert the RCD before use and clean the
ventilation ducts daily. Follow the maintenance instructions
below to blow dry compressed air into the ventilation ducts.
Maintenance
Black & Decker power tools have been designed to operate
over a long period of time with minimal maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling the
tool, press and release the trigger switch to make sure the
tool is already switched off.
Lubrication
This power tool does not require separate lubrication.
Cleaning
Warning! Once visible dust accumulates on the
ventilation ducts and the surrounding,
immediately use dry air to blow away dust and
grit out of the interior of the housing. You need to wear
approved eye and facial protective gear when performing
this process.
Warning! Never use solvents or harsh
chemicals to clean non-metal parts of the tool.
These chemicals may weaken the material of
the parts. Use only mild soap and damp cloth to clean the
tool. Never let any liquid get inside the tool; never immerse
any part of the tool into liquid.
11
ENGLISH
Accessories
Warning! Excluding accessories provided by Black &
Decker, all other accessories have not been tested for
product compatibility. Using such accessories together with
this tool may cause safety hazards. To minimize the risk of
personal injury, we recommend you to use only Black &
Decker accessories with this product.
Please inquire at your dealer for more information regarding
suitable accessories.
Technical Data
BPGS8100 BPGS8115
Input power W 850 850
No-load speed/rated speed
/min 11,000 11,000
Wheel diameter mm 100 115
Grindig wheels thickness mm 6 6
Type of wheel 27 27
Spindle diameter M10 M14
Weight kg 2.2 2.2
12
ENGLISH
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker
product needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and used
again. Reuse of recycled materials helps prevent
environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
Remarks
• Black & Decker's policy is one of continuous
improvement to our products and as such, we reserve
the right to modify product specifications without prior
notice.
• Standard equipment and accessories may vary by
country.
• Product specifications may differ by country.
• Complete product range may not be available in all
countries. Contact your local Black & Decker dealers for
range availability.
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 12
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
make sure of the minimum inconvenience to the customer
unless:
• The product has been used for trade, professional or hire
purposes.
• The product has been subjected to misuse or neglect.
• The product has sustained damage through foreign
objects, substances or accidents.
• Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our aftersales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
products is available at www.blackanddecker.co.uk.
Loading...