Black & Decker Bpgl2009, Bpgl2007 Instruction Manual [ar]

BPGL2009

www.blackanddecker.ae

BPGL2007

ENGLISH

5 7

A B

C D

15 14 12

ENGLISH

Intended use

Your Black & Decker angle grinder has been designed for grinding and cutting metal and masonry using the

appropriate type of cutting or grinding disc. When ﬁtted with

the appropriate guard, this tool is intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all instructions. Failure to follow all instructions

may result in electric shock, ﬁre and/or serious

injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets will reduce risk of

electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

ENGLISH

f. If operating a power tool in a damp location is

unavoidable, use a Residual Current Device (RCD) protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not use a power tool while you are tired or under the

inﬂuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your ﬁnger on the

switch or energising power tools that have the switch on

invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for grinding,

sanding, wire brushing, polishing or abrasive

cutting-off operations

• This power tool is intended to function as a grinder,

sander, wire brush, polisher or cut-off tool. Read all safety warnings, instructions, illustrations and

speciﬁcations provided with this power tool. Failure

to follow all instructions listed below may result in electric shock, ﬁre and/or serious injury.

ENGLISH

• Operations for which the power tool was not

designed may create a hazard and cause personal injury.

• Do not use accessories which are not speciﬁcally

designed and recommended by the tool manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

• The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed

can break and ﬂy apart.

• The outside diameter and the thickness of your

accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

• The arbour size of wheels, ﬂanges, backing pads or any other accessory must properly ﬁt the spindle of

the power tool. Accessories with arbour holes that do not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart

during this test time.

• Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping ﬂying debris

generated by various operations. The dust mask or

respirator must be capable of ﬁltering particles generated

by your operation. Prolonged exposure to high intensity noise may cause hearing loss.

• Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may ﬂy away and

cause injury beyond immediate area of operation.

• Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

shock the operator.

• Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

• Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.

• Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

• Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool's air vents. The

motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause

electrical hazards.

• Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

Note:

The above warning does not apply for power tools

speciﬁcally designed for use with a liquid system.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory's rotation at the point of the binding.

ENGLISH

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel's movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

• Maintain a ﬁrm grip on the power tool and position

your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

• Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

• Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel's movement at

the point of snagging.

• Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

• The guard must be securely attached to the power

tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator.

The guard helps to protect operator from broken wheel fragments and accidental contact with wheel.

• Wheels must be used only for recommended

applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to these

wheels may cause them to shatter.

• Always use undamaged wheel ﬂanges that are of

correct size and shape for your selected wheel.

Proper wheel ﬂanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel ﬂanges.

• Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not

suitable for the higher speed of a smaller tool and may burst.

Additional safety warnings speciﬁc for abrasive

cutting-off operations

• Do not "jam" the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth of cut. Over stressing the wheel increases the loading

and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

• Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power

tool directly at you.

• Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

Safety warnings speciﬁc for grinding and abrasive

cutting-off operations

• Use only wheel types that are recommended for your power tool and the speciﬁc guard designed for

the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and

are unsafe.

• When wheel is binding or when interrupting a cut for

any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheel binding.

• Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

ENGLISH

• Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.

• Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

Safety warnings speciﬁc for sanding operations

• Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

Safety warnings speciﬁc for polishing operations

• Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and

spinning attachment strings can entangle your ﬁngers or

snag on the workpiece.

Safety warnings speciﬁc for wire brushing operations

• Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush.

The wire bristles can easily penetrate light clothing and/or skin.

• If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush

may expand in diameter due to work load and centrifugal forces.

Safety of others

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:

• Injuries caused by touching any rotating/moving parts.

• Injuries caused when changing any parts, blades or accessories.

• Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks.

• Impairment of hearing.

• Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF.)

Voltage drops

Inrush currents cause short-time voltage drops. Under unfavourable power supply conditions, other equipment may be affected. If the system impedance of the power supply is

lower than 0.247 Ω, disturbances are unlikely to occur.

Labels on tool

The following pictograms are shown on the tool:

Warning!

read the instruction manual.

Wear safety glasses or goggles when operating this tool.

Wear ear protection when operating this tool.

To reduce the risk of injury, the user must

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating plate.

• If the supply cord is damaged, it must be replaced by

the manufacturer or an authorised Black & Decker

Service Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Lock-off button

3. Side handle

5. Spindle lock

5. Guard

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

• Press the guard down and insert the screws (9) into the

holes.

• Tighten the screws.

Removing

• Remove the screws (9).

• Remove the guard from the tool.

Warning! Never use the tool without the guard.

Adjusting the guard (ﬁg. B)

The guard can be rotated 180°.

• Slacken the screws (9) and the nut (10).

• Rotate the guard as required.

• Re-tighten the screws and the nut.

Fitting the side handle

• Screw the side handle (3) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing the guard (ﬁg. A)

The tool is supplied with a guard intended for grinding

purposes only. If the unit is intended to perform cutting off

operations, a guard speciﬁc for this operation must be ﬁtted.

A suitable guard for cutting off operations part number

1004484- 03 is available and can be obtained from Black &

Decker service centres.

Fitting

• Place the tool on a table, with the spindle (6) facing up.

• Hold the guard (5) over the tool as shown.

• Align the holes in the adjusting plate (7) with the screw

holes (8).

Fitting and removing grinding or cutting discs (ﬁg. C - F)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size

(see technical data). The maximum thickness for grinding

discs is 6 mm, for cutting discs 3.5 mm.

Fitting

• Fit the guard as described above.

• Place the inner ﬂange (11) onto the spindle (6) as shown (ﬁg. C). Make sure that the ﬂange is correctly located on the ﬂat sides of the spindle.

• Place the disc (12) onto the spindle (6) as shown (ﬁg. D).

If the disc has a raised centre (13), make sure that the

raised centre faces the inner ﬂange.

ENGLISH

• Make sure that the disc locates correctly on the inner ﬂange.

• Place the outer ﬂange (14) onto the spindle. When ﬁtting a grinding disc, the raised centre on the outer ﬂange must face towards the disc (A in ﬁg. E). When ﬁtting a cutting disc, the raised centre on the outer ﬂange must face away from the disc (B in ﬁg. E).

• Keep the spindle lock (4) depressed and tighten the outer ﬂange using the two-pin spanner (15) (ﬁg. F).

Removing

• Keep the spindle lock (4) depressed and loosen the outer ﬂange (14) using the two-pin spanner (15) (ﬁg. F).

• Remove the outer ﬂange (14) and the disc (12).

Use

Warning! Let the tool work at its own pace. Do not overload.

• Carefully guide the cable in order to avoid accidentally

cutting it.

• Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

• Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting disc.

Switching on and off

• To switch the tool on, press the lock-off button (2) and

subsequently press the on/off switch (1).

• To switch the tool off, release the on/off switch (1).

Warning! Do not switch the tool off while under load.

Hints for optimum use

• Firmly hold the tool with one hand around the side

handle and the other hand around the main handle.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/ cordless power tools:

• Switch off and unplug the appliance/tool.

• Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

• Or run the battery down completely if it is integral and

then switch off.

• Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

• Regularly clean the ventilation slots in your

appliance/tool/ charger using a soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

• Regularly open the chuck and tap it to remove any dust from the interior (when ﬁtted).

Accessories

The performance of your tool depends on the accessory used. Black & Decker accessories are engineered to high quality standards and designed to enhance the performance of your tool. By using these accessories you will get the very best from your tool.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be ﬁtted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the new

plug.

• Connect the blue lead to the neutral terminal.

• When grinding, always maintain an angle of approx. 15°

between the disc and the workpiece surface.

Warning! No connection is to be made to the earth terminal.

Follow the ﬁtting instructions supplied with good quality plugs. Recommended fuse: 13 A.

ENGLISH

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.

Should you ﬁnd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again.

Reuse of recycled materials helps prevent environmental

pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofﬁce at the

address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.

Technical data

BPGL2009 BPGL2007

Input voltage Vac 220-240 220-240

Power input W 2,000 2,000

Rated speed /min 6,500 8,400

Disc Diameter mm 230 180

Max disc thickness

grinding discs mm 6 6

cutting discs mm 3.5 3.5

Spindle size M14 M14

Weight kg 7 7

Guarantee

Black & Decker is conﬁdent of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 12 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to make sure of the minimum inconvenience to the customer unless:

The product has been used for trade, professional or hire

purposes.

The product has been subjected to misuse or neglect.

The product has sustained damage through foreign

objects, substances or accidents.

Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

ENGLISH

To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker ofﬁce at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk.

+ 23 hidden pages