Page 1
8 1
Distributed by: Directed Electronics
Address: 44 Translink Drive, Keilor Park Victoria Australia 3042
PH: + 61 03 8331 4800 Email: service@directed.com.au
Baccus Worldwide LLC
Weena 290, 3012 NJ Rotterdam or
Postbus 819, 3000 AV Rotterdam
+31(0)10 282 16 11
Cat. # BDPC400AU September 2016
RD091216 Printed in China
500 WATT POWER INVERTER
WITH USB CHARGING PORT
INSTRUCTION MANUAL
BDPC400AU_Manual_091216.indd 8-1 9/12/2016 11:55:45 AM
Page 2
32
INSTRUCTION MANUAL
INTENDED USE
Your Black & Decker power inverter is designed to
convert direct current (dc) to alternating current
(AC). It allows the 12V dc current in an automobile to
supply ac power to operate equipment that is normally
supplied from a mains power source. This product is
intended for household, consumer use only.
SAFETY INSTRUCTIONS
Warning!
When using battery-powered appliances,
basic safety precautions, including the following,
should always be followed to reduce the risk of fire,
leaking batteries, personal injury and material damage.
•Read all of this manual carefully before using the
appliance.
•The intended use is described in this manual.
The use of any accessory or attachment or the
performance of any operation with this appliance
other than those recommended in this instruction
manual may present a risk of personal injury.
•Retain this manual for future reference.
Using your inverter
Always take care when using the inverter.
•For indoor or in-car use only.
•This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
•Children should be supervised to ensure that they do
not play with the appliance.
•Use in a dry location only. Do not allow the appliance
to become wet. Do not immerse the appliance in water.
•Do not open body casing. There are no user-
serviceable parts inside.
•Do not operate the appliance in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.
•To reduce the risk of damage to plugs and cords
never pull the cable to remove the plug from a
socket.
After use
•When not in use, the appliance should be stored in a
dry, well ventilated place out of the reach of children.
•Children should not have access to stored appliances.
•When the appliance is stored or transported in a
vehicle it should be placed in the boot or restrained
to prevent movement following sudden changes in
speed or direction.
•The appliance should be protected from direct
sunlight, heat and moisture.
Inspection and repairs
•Before use, check the appliance for damaged or
defective parts. Check for breakage of parts, damage
to switches and any other conditions that may affect
its operation.
•Do not use the appliance if any part is damaged or
defective.
•Have any damaged or defective parts repaired or
replaced by manufacturer.
•Never attempt to remove or replace any parts other
than those specified in this manual.
Specific safety instructions for power
inverters
Warning!
This appliance converts power from a 12V
dc battery to mains supply voltage. Take precautions,
including the following, to avoid the risk of electric
shock.
•Only connect a plug fitted to the supply cord of an
appliance to the inverter.
•Never connect an appliance by modifying the plug or
by using an adapter unless otherwise instructed by
this instruction manual.
•The length of an appliance power cord to the inverter
must not exceed two metres unless otherwise
instructed by this instruction manual.
•Never connect an appliance that is damaged or
incomplete.
•Never connect the inverter to the mains supply or to
the output of another inverter.
– The inverter cannot convert the mains supply
to dc voltage.
– The inverter cannot be used to supplement
the mains supply.
•Disconnect the 12V dc accessory plug from the
power source and remove the appliance plug from
the inverter before performing any maintenance or
before cleaning the appliance.
•Do not cover the inverter. Only use in well ventilated
areas.
•Do not open the inverter, there are no serviceable
parts inside. Do not probe the inverter.
•Check that connections to the dc supply are clean
and secure. Loose connectors may cause overheated
wires and melted insulation.
•Check to make sure you have not reversed the polarity.
•Do not install in engine compartments.
•Do not use the inverter to supply any medical devices.
Warning!
A reverse polarity connection will result in a
blown fuse and may cause permanent damage to the
power inverter. Damage due to reversed polarity is not
covered by the warranty.
Warning!
Do not use with positive ground electrical
systems, (i.e. older vehicles).
2
4
7
6
3
1
9
5
8
BDPC400AU_Manual_091216.indd 2-3 9/12/2016 11:55:46 AM
Page 3
4 5
The power inverter output waveform
The ac output waveform of this inverter is known
as a “modified sine wave.” This type of waveform
is suitable for most ac loads, including linear
and switching power supplies used in electronic
equipment, transformers, and small motors.
Warning! Rechargeable devices:
Some
rechargeable devices do not operate well from a
modified sine wave inverter. They only operate
correctly from a standard household outlet
which provides a pure sine wave. Therefore, the
manufacturer recommends that you operate these
types of devices from a standard household outlet
only, not from the inverter.
This problem does not occur with the majority of
battery-operated equipment. Most of these devices
use a separate charger or transformer that is plugged
into an mains socket. The inverter is easily capable of
running most chargers and transformers.
Caution! Incompatible products:
Certain products
contain power supplies or circuits that are not
compatible with an inverter using a modified sine wave
output (such as this inverter) and may be damaged by
using this inverter.
Some products must be powered from a pure sine
wave power source, such as standard household
power, or a “pure sine wave” inverter in order to
function properly. If your product requires pure
sine wave ac input power to function properly, the
instruction manual for your product could state
this. If in doubt, you should contact your product
manufacturer PRIOR TO USE.
Your product could be damaged by this inverter if it
contains:
•Microwave ovens
•Transformerless battery chargers
•Capacitive coupled power supplies
If an incompatible product is used with this inverter:
•The product might not operate at all, with no
indication of failure. The product fuse might open as
a result of trying to use it with the inverter.
•The product might exhibit unusual operation (such
as, intermittent operation, buzzing, and the like.)
Warning!
This appliance will not operate high wattage
appliances or equipment that produce heat, such as
coffee makers, hair dryers, microwave ovens, and
toasters.
Note:
Some laptop computers may not operate with
this inverter.
Rated versus actual power
requirements of equipment
Most electrical tools, appliances and audio/video
equipment have labels that indicate the power
consumption in amps or watts. Be sure that the power
consumption of the item you wish to operate is rated
at 500 watts or less.
The power inverter is fitted with overload protection
and will shutdown if a load in excess of 500W is
applied. Resistive loads (i.e incandescent lights) are
the easiest for the power inverter to run.
Specific safety instructions for the
USB power port
•Do not insert foreign objects into the USB power
port.
•Do not attach USB hubs or more than one personal
electronic device to the USB power port.
•Some USB-powered household electronics may not
operate with this USB power port. Check the manual
of the corresponding electronic device to confirm
that it can be used with this type of USB power port.
FEATURES
1. Power/fault LED
2. On/off switch
3. Mounting brackets (4 in total: 2 in front,
2 in back)
4. Battery clamps
5. USB power port
6. Mains socket
7. Terminals (back of unit)
8. Ventilation slots
9. 12V dc accessory plug
POWER SOURCE REQUIREMENTS
The power source must provide 12V dc and must be
able to supply the necessary current to operate the
load.
Warning!
The power inverter must be connected only
to batteries with a nominal output voltage of 12 volts.
The appliance will not operate from a 6 volt battery
and will sustain permanent damage if connected to a
24 volt battery.
Connecting to a power source
The power inverter comes equipped with a 12V dc
accessory plug and battery clamps for connection to a
dc power source.
Note:
For optimal performance make sure that the engine
is running while operating the inverter. However,
the power inverter may not operate while the
engine is starting because battery voltage can drop
substantially during cranking.
OPERATING INSTRUCTIONS
Connecting to a power source using
the 12V dc accessory plug
UP TO 100W ONLY
The 12V dc accessory plug is suitable for operating
the power inverter at power outputs up to 100 Watts
only. The tip of the plug is positive (+) and the side
contact is negative (–).
Warning!
Make sure that the On/Off button is turned
off (0) and that no flammable fumes are present in the
installation area before connecting the accessory plug
to the accessory outlet.
Warning!
Connect the ring terminals to the terminals
of the power inverter before connecting the accessory
plug to the accessory outlet
•Connect the ring terminal of the red cable to the
red terminal marked (+) on the back of the power
inverter.
•Connect the ring terminal of the black cable to the
black terminal marked (–) on the back of the power
inverter.
•Connect the power inverter to the power source
by inserting the 12V dc accessory plug firmly into
the accessory outlet of a vehicle or other dc power
source.
•The Power/Fault Indicator lights steadily when the
inverter is properly connected to a functioning dc
power source and On/Off switch is in the on (I)
position. This indicates that the mains and USB
power ports are ready to use.
Note:
If the inverter does not work, make sure the
ignition/accessory switch is actually powering the
vehicle accessory socket. Some vehicles require
the ignition switch to be turned on.
Important:
If the Power/Fault Indicator flashes, a
fault has occurred. Refer to the Protective Features
Section and the Troubleshooting Section of this
Instruction Manual.
Connecting to a power source using
the cables
UP TO 500W
Use the cables and connect the appliance directly to
the 12 Volt power source as follows:
•Make sure that the On/Off button is turned off (0)
and that no flammable fumes are present in the
installation area.
•Connect the red cable to the red terminal marked (+)
on the back of the power inverter.
•Connect the black cable to the black terminal marked
(–) on the back of the power inverter.
•Connect the red battery clamp to the positive
terminal of the battery.
•Connect the black battery clamp to the negative
terminal of the battery.
•Make sure that all connections between the battery
clamps and the terminals are secure.
•The Power/Fault Indicator lights steadily when the
inverter is properly connected to a functioning dc
power source and On/Off switch is in the on (I)
position. This indicates that the mains and USB
power ports are ready to use.
Important:
If the Power/Fault Indicator flashes, a
fault has occurred. Refer to the Protective Features
Section and the Troubleshooting Section of this
Instruction Manual.
Warning!
Loose connectors may cause overheated
wires and melted insulation.
Operation of the mains socket and
USB power port
1. Connect the inverter to a functioning 12V dc
power source as described in this instruction
manual. Make sure there is adequate space for
proper ventilation around the inverter.
2. Press the on/off button to turn the unit on.
3. The power/fault Indicator lights steadily, indicating
a proper connection.
4. The standard mains and USB power ports allow
simultaneous operation of multiple devices.
Simply plug the ac appliance into the inverter’s
mains socket and/or plug the USB powered device
into the inverter’s USB power port and operate
normally.
Important:
If the power/fault Indicator flashes, a
fault has occurred. Refer to the Protective features
section and the Troubleshooting section of this
instruction manual.
Notes:
Ensure that the wattage of all equipment
simultaneously plugged into the inverter does not
exceed 500 watts continuous.
This inverter’s USB power port does not support
data communication. It only provides 5 volts/500mA
dc power to an external USB-powered device.
5. To turn the inverter off, switch off the on/off
button and disconnect it from the 12 volt dc
power source.
Important:
Remember to disconnect the inverter from
any power source when it is not in use.
Connection to load
The power inverter is equipped with a standard mains
socket. Plug the cord from the equipment you wish
to operate into the mains socket. Make sure that
the load requirement of your equipment does not
exceed 100 or 500 watts (depending on the type of dc
connection).
The appliance is engineered to be connected directly
to standard electrical and electronic equipment in
the manner described above. Do not connect the
inverter to household mains wiring. Do not connect
the inverter to any ac load circuit in which the neutral
BDPC400AU_Manual_091216.indd 4-5 9/12/2016 11:55:46 AM
Page 4
6 7
conductor is connected to ground (earth) or to the
negative of the dc (battery) source.
Warning!
Do not connect to ac wiring.
PROTECTIVE FEATURES OF
THE POWER INVERTER
Your appliance monitors the following potentially
hazardous conditions:
Low battery voltage.
This condition is not harmful to
the appliance but could damage the power source. The
appliance automatically shuts down when input voltage
drops to 10,5 +/– 0,5 volts. When the condition is
corrected, turn the appliance off and then on.
Over voltage.
The power inverter will automatically
shutdown when the input voltage exceeds 15,5 +/–
0,5V dc.
Short circuit.
A reverse polarity or short circuit
condition may cause external or internal fuses to open
and may cause irreversible damage to the appliance.
Take extra care to insure a correct polarity connection.
Overload.
The power inverter will automatically shut
down when the continuous load exceeds 500 watts.
When the overload is removed, reset the appliance by
turning it off and then on again.
Over temperature.
If the temperature inside the
appliance is too high, the appliance will automatically
shut down. Allow the appliance to cool for at least
15 minutes before restarting after a heat-related
shutdown. Unplug the appliance while cooling.
HINTS FOR OPTIMUM USE
For best operating results, the inverter should be
placed on a flat and/or solid surface. The inverter
should only be used in locations that meet the
following criteria:
DRY:
Do not allow water or other liquids to come into
contact with the inverter.
COOL:
The surrounding air temperature should be
between 5°C and 40°C. Keep the inverter away from
direct sunlight, when possible.
WELL VENTILATED:
Keep the area surrounding the
inverter clear to ensure free air circulation. Do not
place items on or over the inverter during operation.
The inverter will shut down if the internal temperature
gets too hot. Refer to the Protective features section of
this instruction manual for more information.
SAFE:
Do not use the inverter near flammable
materials or in any location that may accumulate
flammable fumes or gases. This is an electrical
appliance that can briefly spark when electrical
connections are made or broken.
TROUBLESHOOTING
Common Audio/Visual Problems
Buzzing Sound In
Audio Systems
Some inexpensive stereo
systems make a buzzing
sound when operated from
an inverter because the power
supply in the electronic device
does not properly filter the
modified sine wave. The only
solution to this problem is to
use a sound system that has
a higher quality power supply.
Television
Interference
The inverter is shielded to
minimize interference with
television signals. However, in
some instances, interference
may still occur, particularly
where television signals
are weak. Try the following
corrective measures:
•Place the inverter as far as
possible from the television,
the aerial or cables. Use
an extension cable, if
necessary.
•Readjust the orientation of
the inverter, the aerial or
cables and the television
power cord to minimize
interference.
•Make sure the aerial or
cable feeding the television
provides an adequate
(“snow free”) signal and that
high quality, shielded aerial
or cable is used.
•Do not use the inverter
to operate high-power
appliances or tools at the
same time you are using it
to operate the television.
Common Power Output Problems
If the inverter on/
off switch has been
pressed to turn the
unit on, but there
is no mains or
USB power output
and the power/fault
LED is not lit:
•Press the on/off switch to
turn the unit off.
•Check the dc connections.
Tighten if necessary.
•Check the fuse in the dc
vehicle power cord plug.
Change if necessary.
•Press the on/off switch again
to turn the unit back on.
Common Power Output Problems
If the inverter on/
off switch has been
pressed to turn the
unit on, but there
is no mains or
USB power output
and the power/
fault LED flashes,
then one of
the following
conditions has
occurred:
•Low battery voltage.
•Over voltage.
•Short circuit.
•Overload.
•Over temperature.
Press the on/off switch to
turn the inverter off, correct
the fault and then press the
on/off switch again to turn
the inverter back on.
MAINTENANCE
From time to time wipe the outside casing of the
inverter with a damp cloth. Do not use any abrasive
or solvent-based cleaner. Do not immerse the inverter
in water.
Warning!
Before performing any maintenance or
cleaning on the inverter, disconnect it from any power
source.
Replacing the fuse in the dc power
cord plug
•Remove the grooved cap by turning it counter
clockwise.
•Remove the rubber washer, centre pin and the
spring.
•Remove the fuse.
•Fit a new fuse of the same type and size (12A/250V).
•Install the centre pin, spring and rubber washer.
•Install the grooved cap by turning it clockwise onto
the plug.
PROTECTING THE ENVIRONMENT
Correct disposal of this product
This marking indicates that this product
should not be disposed with other
household waste throughout the EU. To
prevent possible harm to the environment
or human health from uncontrolled
waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return
your used device, please use the return and collection
systems or contact the retailer where the product
was purchased. They can take this product for
environmentally safe recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
TECHNICAL DATA
Input voltage: 12,5V dc, 48A
Output voltage: 230-240V ac, 50 Hz
Power output: 500W continuous
USB: 5V dc, 500mA
Output waveform: Modified sine wave
Dc plug fuse: 12A/250V
WARRANTY
Our goods come with guarantees that cannot be
excluded under the Australian & New Zealand
Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation
for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of
acceptable quality and the failure does not
amount to a major failure.
Baccus Worldwide LLC is confident of the quality of
its products and offers an outstanding warranty. This
warranty statement is in addition to and in no way
prejudices your statutory rights under the Australian &
New Zealand Consumer Law.
If a Baccus Worldwide LLC product becomes
defective due to faulty materials, workmanship or
lack of conformity, within 24 months from the date
of purchase, Baccus Worldwide LLC guarantees to
replace defective parts, repair products subjected to
fair wear and tear or replace such products to make
sure of the minimum inconvenience to the customer
unless:
•The product has been used for trade, professional or
hire purposes;
•The product has been subjected to misuse or
neglect;
•The product has sustained damage through foreign
objects, substances or accidents;
•Repairs have been attempted by persons other than
Baccus Worldwide LLC service staff.
To claim on this warranty, you will need to submit
proof of purchase and return the allegedly defective
product to Baccus Worldwide LLC’s local market
distributor, at your expense.
Please visit our website www.baccusworldwide.com
to register your new Baccus Worldwide LLC product
and to be kept up to date on new products and special
offers. Further information on the Baccus Worldwide
LLC brand and our range of products is available at
www.baccusworldwide.com.
BDPC400AU_Manual_091216.indd 6-7 9/12/2016 11:55:46 AM
Loading...